DIY Painting Without a Paint Booth!

No Fancy Tools needed for this Garage Paintjob! In the episode we will show you how to properly use spray cans to paint your project and HOW TO get the best possible outcome when it comes to doing a small paint job in your garage. Click that play button to get your project started!
🟢CHECK OUT OUR ONLINE STORE🟢
www.amazon.com...
🔺Get the OFFICIAL Paint Society Paint Suite Here🔺
amzn.to/3Eq3pSf
🔺Get the OFFICIAL Paint Society Pump Sprayer Here🔺
amzn.to/49kZbsY
*To Recieve 10% off #Eastwoodco Products use coupon code BRIAN10 at eastwood.com
Products in this Video:
Degreaser: amzn.to/3T0I8a3
Tear Away Microfiber Towels: amzn.to/4bKNSw6
Heat Gun: amzn.to/3UL2cyh
Palm Sander: amzn.to/3I7msmp
5 Inch Interface Pad: amzn.to/49wlA6E
Sandpaper Assortment Needed: amzn.to/3wmtOjd
UV Putty: amzn.to/49E5xU7
UV Curing Flashlight: amzn.to/3SGPb6p
Bondo Spreaders: amzn.to/3OMCuWq
Sanding Block: amzn.to/49GIici
Recommended 2k Eastwood Primer: amzn.to/49jkgnP
Primer Used in Video: amzn.to/3uFTJlC
Guide Coat: amzn.to/3UFDgIE
Eastwood Clearcoat: amzn.to/4bBpOvv
K800 Sandpaper: amzn.to/3QghmaK
Tack rags: amzn.to/3kM2YIg
Sprayway Glass Cleaner: amzn.to/3vPNxVF
Respirator: amzn.to/3vPNxVF
OEM Colors in a Can: Paintscratch.com

[@tp5337]

I've said it before and I'll say it again, Brian, you are an excellent teacher. Thank You TP

[@donford4403]

Man I’m from the uk and never stop watching your shows loving this, you’re a clever guy with fantastic calm and excellent explanations. Keep up the good work. 🔥🤙

[@matthewobrien1188]

Hi Brian. Love your channel, I’ve been a builder for 40 years in Australia but I now think that I chose the wrong profession. So drawn to your painting. Never too late to change careers, you make it so interesting and informative. Well done mate!!!

[@fish9651]

When Spring arrives I need to do quite a bit on my EK. Thanks for the "How to..." and the inspiration.

[@judih.8754]

Brian you're a natural teacher!! I just bought a few items off your list to touch up my car. Thanks for an informative video!

[@TheMrDubstepic]

That respirator for the 2k is the key in all this! That stuff is brutal.

[@PaintGuy_]

“The curb just got us” lol. Perfect teaching though!

[@AlexRH1991]

Nice job I started painting my own cars a bit ago and you are 100% correct that clear coat brand from the can is the only way the paint will shine. Any other kind of clear does not look good no matter how hard you try

[@LenWhalenX]

Man, this is a great video! There's a couple of young guys that were asking me about stuff like this last week. I'm definitely sending this video their way!

[@michaelcannon6462]

" The curb just got us" lol, I think you got the curb.

[@alirazmjou2149]

Thank you so much for this video متشکرم از شما آقای محترم

[@andyb7754]

Very nice garage repair. Thank you.

[@royosborn7869]

Thanks Brian - nice job

[@aros007z]

Awesomeness

[@cliveharris4555]

As always Brian very very informative clear and precise makes me want to rush into my garage and get my spray gun out right away even though it’s freezing 🥶 wet and windy here in the UK ! Perhaps I will leave it for a couple of months, keep up the great work Brian absolutely brilliant as always 👍🏻😉

[@lawncuttingplusdelta]

Great little complete demo !!

[@novabig]

Another great video. Thanks Brian! 👏👏👏

[@zeyadqaddoori2065]

Thank you from the heart! You taught me a lot and i keep learning from you sir! Thanks again Brian

[@peglegtoo]

Great video. Nice to know about the uv putty, really helps move the project along.

[@lawrenceveinotte]

Nice work, the crane on the crane truck at work hit the back of the cab, not sure if I did it but I had borrowed it so I'm going to fix it, small ding and scratched some paint, uv putty looks nice, etch primer, Eastwood clear, should turn out fine, thanks

[@StephenBrewer89]

Just sprayed a fever in my Benz with this method. Blended to the back of the fender flawlessly. Then cleared the entire panel. Thanks Brian!

[@jagovanbeek]

I think you just solved a problem I was having. Thanks Brian!

[@hundredlives3910]

what filter do you use in your respirator? online results are pretty mixed for 2k clear

[@JoseVelez-uj1mz]

More of this DIY... please, great work 👍

[@fsl4346]

Always delivers!! Coach T doing great work.💪🏽😎

[@IOERROR622]

After watching your channel for a while now I feel confident I can paint my car. I've done the Plasti-dip with a sprayer years ago when I was younger and it turned out nice (for Plasti-dip). I am now working on a resto-mod C4 Corvette that needs a full paint job. One quick question, I live in the northeast USA. When is the best time to paint, spring, summer or fall? I'll be using a inflatible outdoor paint booth that I can either place in a shady area or directly in the sun. Finally thanks for the awesome videos.

[@BeeLineFab]

Body work is Supreme! If I ever switch career it would be doing this

[@leosun1387]

That looks beautiful 😍

[@timwest9300]

I love it Brian you are great I appreciate your time and efforts to help us be better technicians and dys thank you sir God bless we love you

[@JP-vs1ys]

Brian always makes it look easy.

[@indyrock8148]

I must say i am impressed with how many product placements you achieved for a small bumper rash

[@PaintSociety]

I’m impressed that this is your best comment.

[@rmg8729]

Hi Brian, why didnt you use adhesion promoter on the bare plastic? Genuine question as I’m no expert

[@PaintSociety]

You can but it was sanded with 320. If I had some I would have used it

[@rmg8729]

@@PaintSociety thanks !

[@conorkar2492]

very well done Brian, the paint turned out great, but now i feel like the rest of the car would love a polish to match the shiny bumper XD. Thank you for all the information and keep up the great work.

[@RishMedia]

Great to see this. Prepping to repaint my Tsx engine bay but I’ve been on the fence. Cant decide on a compressor setup and ideal for my spacing. And definitely not confident using the 6 Gal pancake I have. So deciding to use cans from the paint Store. Probably more costly this way to but I’d feel more confident. Someone mentioned the 2k Pro max clear won’t hold up with heat the bays/Florida produces.

[@pingpoon8394]

Hi Brian: I always want to know when you back sanding with 600, are you just sanding the surrounding area but not the repair area? If the answer is yes, than why don't you just sand the whole thing with 600 since the primer is able to grip on 600 scratch anyway? Thank you

[@pingpoon8394]

Hi Brain, question come up again, yes, i am a slow learner. but is important to not to skip. On 16:05 you said using 800 final scuff for base coat, but why is you are doing 600 on DA showing on the video? Do you mean first using 600 on DA, and use 800 scuff on the hard to reach areas? Thanks again

[@PaintSociety]

Yes

[@pingpoon8394]

@@PaintSociety , thanks Brain for your reply

[@mikefourby6011]

When I use a cheap sander that doesn't have a speed adjustment I use a reastat I got from harbor freight to slow down the speed of the sander the slower the speed the better the sand and the longer the sandpaper last keep up the good work 👍

[@ceesklumper]

Brian elated with his own work. Deserved.

[@speedokoterefinishnetwork4937]

Bryan in a HONDA... WOOOOTT!!! LOL nice ride man and super nice repair!!!!!

[@PaintSociety]

You know it!

[@speedokoterefinishnetwork4937]

@@PaintSociety and you have it fitted up perfect which looks to be a factory hfp kit??!!!!

[@harmonyisblessing2482]

You can learn more on youtube now days than you can in school 😮😮

[@prm5798]

Hi Brian, could you make a video on the best way to paint scrapes on lower edge of doors? Like when a door is opened over a high sidewalk. Here in the rust belt, rust quickly starts in this area if not repaired properly. Thanks

[@jimdrechsel3611]

Great stuff! I have an engine compartment to redo with a couple bare spots from rust to prepare for sanding. How do you decide whether or not to primer and entire area/panel or just spot areas with primer like the bare metal areas? Would you primer the bare metal with epoxy and then seal the whole area or would you spot prime and then do what you did in this video sanding the existing painted surface to be refinished? Love the channel. Will you do a video or do you have a video showing how to spray a car in a homemade booth or an outside situation? Your garage? Not everyone has access to a spray booth. Thank you

[@BlacksRuinEverything]

So the saving grace for those who don't want to go through all of this is the Eastwood 2K clearcoat or Spraymax 368 0061. It can make childrens finger paint look like a show car finish.

[@daffiecars]

Lol no you still need all the prepwork or it wil still look like shit

[@kyrosavcic7382]

Also u need a booth for 2k if ya don't the fumes r dangerous and also u will still get dust nibs

[@dennyross5602]

This is a really cool channel Brian. I like especially how you use your Honda. Awesome stuff tbh tho really.

[@Funtimes670]

Thank you!

[@uses0ap]

What is your opinion of "ready-to-spray" quarts/pints of oem color products (i.e. paintscratch / automotive touchup / etc)

[@PaintSociety]

Good for small stuff like this or one panel

[@41maddriver]

Question: what causes the putty to bleed through the finish coat on a light color? Thank you.

[@BUY_YOUTUB_VIEWS_841]

Perfect timing for this content

[@Alan_27ATH]

Excellent video, clearly detailed and everything explained. Do you have a video on repainting a used plastic bumper? Clear coat is coming off mine so wanting to repaint it. Does all the paint got to come off? Does plastic primer need to be used or only on areas where the is no paint? etc. etc.

[@adrianstone7151]

Hello Brian. Great videos! So PPG Envirobase, what's your take on it? I'm a Jeeper and would really like to see you paint a Wrangler. With all the exposed hinges, nuts and bolts.

[@jobsearch5871]

do you think the UV Putty will work to fill in rock chips ? Then apply the touch up paint over that ? I go and look if you have any videos of taking care of rock chips

[@TK42138]

Great result.

[@johnochicago8457]

In the older days when I worked in body shops we didn't have UV we used bondo. We would also prime and sand after the bondo until it was smooth and even. Then if we didn't need to paint the entire panel, we would spot blending. Can spot blending be used or does the entire panel require painting?? Thank you!!!!

[@johnochicago8457]

Thank you so much. I will look at 3HP compressor and a 50L tank and three good spray guns. It's been years since I did this and oh how things have changed. I remember using 42lps pressure with acrylics, using thick primer for the fill coat after bondo and sand and prime then use a think coat of primer by adding thinner and knocking the top off. Then use prepsol and a thin first coat of paint first and at least two more color then top coat blender which requires 70lbs pressure and running back and forth to paint the side of a car. It ran notoriously if you didn't move fast.

[@wjthehomebuilder]

I've never seen that UV filler. Nice!!

[@kevinberlyn8060]

Gday Brian. always enjoy your videos. very informative and take the "Scare" out of painting at home.. question if I may. I am about to paint a classic mini. I won't be using 2K paint for 2 reasons.. 1. old cars don't look right with modern paints and 2 I can't spray 2K at home. I am using the old school paint called cellulose. have you ever sprayed with it ? if so do you have a video online I can watch ?

[@giulianoseguro5071]

Love the videos man, thank you so much! I'm about to do the same on my car. Question, why not use a clear coat blender like UPOL #9 on the edge to blend it in? my repair area is the same size as yours but it's in the trunk so I wanted to avoid having to clear the hole trunk and just blend it in with something like UPOL. Would that work?

[@PaintSociety]

Clear the whole thing. Its much better

[@TiggaVimsta1982]

Hello from Croatia,nice job

[@robertolago7406]

Really nice and always helpful. Big fan! Keep it up!

[@PaintSociety]

Thank you!!

[@dazzamac70]

Great video with very easy steps to follow, well done!!! One question, what Masking (Plastic) Film do you normally use/recommend? Thanks 👍

[@peglegtoo]

also, brand serial number yellow tape

[@gregoryjowers3629]

Looks great Brian

[@zandrick1373]

@Paint Society, I would like to know how you would deal with metal flake that you add into the clear, what steps it would take to make it heavy flaked, and smooth in the end. I did a paint job that turned out ok but I'm not finding a lot of info on these types of things. Not sure if you have an email that I could just send you a better explanation there or pictures of the truck and finish

[@Andre-tc1wj]

Great video. I purchased a cargo van that has several dents on the outside the van. Any way or video or suggestions to smooth it back out. I have no paint booth or garage any suggestions painting outside to keep paint free of dirty.

[@kevinberlyn8060]

gday. First of all, thank you for your KZbin channel. I find your content is certainly helpful and makes me feel more comfortable in attempting to paint my car in my garage. as you say, it's only paint . I am currently in the process of sanding down a classic mini and will be painting it in cellulose lacquer. I know terminologies of words can change across the pond from the UK to the USA. I haven't found any videos on painting a car in cellulose lacquer paint. Can you tell me if cellulose is the same as nitro cellulose. any and all advice on using cellulose would be greatly appreciated. thanks again for the great videos kevin

[@ynottteris]

Quick question, is there a best temperature for spraying? Cheers Tony.

[@silvercommander]

Excellent tutorial

[@PaintSociety]

Glad you think so!

[@stephenherrick6847]

Where is the best place to buy a uv light for uv primer?

[@brucemorris6319]

Well I did learn something today after all 👍

[@Le50179]

Hello Brain, I’m painting a 1968 Pontiac firebird. It’s for my son. I’m at the last stage of painting. The clear coat. I’m using automotive art 4:1 clear. The problem I got in to is pin dots. On the roof and hood. The base is black excel auto body product # 701001. I did all the flash time between coats. Need feedback on what I can do or fix this problem. I laid down two coats of clear and then wet sanded the imperfections. The next step is clear. Any help will be appreciated.

[@gmvibess2297]

Please do a video about paint chipping 😭🙌🏽

[@socalstangman4655]

Brian I have a question. I want to paint the roof of my car black. The paint is perfect in every way, even ceramic coated. What would be the best way to prep this for paint?

[@uses0ap]

Will any etching primer work as a sealer or specifically the brand you've shown?

[@PaintSociety]

I have had great specific luck with this brand. Just make sure if you try don’t use a high build sell etch

[@DubWerks]

Looks great! Have any of your reps come by with the Car-Rep 2K stuff? It's pretty interesting, no bladder of hardener, but it is a 2K.

[@mblake0420]

It's build into the can, it is punctured at the bottom if you watch

[@PaintSociety]

I have some I have to check out. Seems interesting

[@DubWerks]

@@PaintSociety it is! We used some of the clearcoat and it worked very well.

[@fvresonanator]

What filter are you using for 2K? Online says there is no mask filter that can safely trap Isocyanates. Only an air fed mask should be used

[@davidruiz4126]

Hi Brian! Quick question, Im looking to purchase the 3m Xtract electric sander, I notice you own one in one of your videos, have you had any issues with it and how long do you own it for? I saw some bad reviews about overheating and not being reliable? I been using the 3m air Sanders for around 6 years and they are still going strong but I would rather switch to electric to save power and not overuse my compressor that long, plus I can use it anywhere where there is an outlet, let me know and thank you for your help!

[@PaintSociety]

I don’t use mine too much but every time I use it I’m reminded about what a great investment it was.

[@jerryhovet2991]

1:21 - that tire…looks like the curb got your alignment too! 😮

[@PaintSociety]

The tires were flipped

[@jerryhovet2991]

@@PaintSocietyI’m just messin with ya….thank you for all the content, I’ve been watching and planning my first paint job based on your videos. Please keep up the awesome work!

[@lmSteveo]

What kind of vacuum hose reel is that? Do you have a garage tour video?

[@StingrayOfficial]

Great video!

[@Supanova70]

On a classic car all the brackets hinges ect should i epoxy or just rattle can rustoleum? or both?

[@wyattoneable]

Outstanding.

[@jimfeaster4837]

😊good video

[@robertgrlic6505]

Great job!

[@wadee170]

I want to paint the wheel moldings and the bumper the same color as the vehicle. What is the best way to proceed? It's a Ford Explorer.

[@augustinpadilla5755]

Love this guy

[@toycoma98]

I noticed your tire wear. Check your tire pressures, wear on the outer thread means low pressure. Check tierods, and balljoints, may need alignment. Now go through the drive through to celebrate!

[@JackdeDuCoeur]

Nice work

[@terrencecoughlan5704]

Haahhaaaa the curb got it 😂

[@joelaguirre1318]

Brian I'm new to the channel Question what is a good air compressor I could use as a beginner to get good air pressure and that's less expensive?

[@tcorley7477]

Have you ever used the spray max brand primers and any opinions on the brand? I believe it's made by usc

[@DoubbleAgent]

Great video/advice 🫡

[@CybekCusal]

I'm really struggling blending the repaired area into the undamaged area. I get a weird overspray mess. How far away are you when you spray? I can't tell from the video.

[@PopsiccDesigns]

Hey Brian, have you ever light sanded metallic base to smooth the coat before clear? I've heard from some people to never sand metallic base but I've seen some people do it in videos so I'm a little confused.

[@PaintSociety]

You can sand it but you Must always recoat. I chatted about this briefly in this video

[@brucekramer3213]

For a Stuefloten-quality finish, … no short cutting now. I’ll find the patina-finish clip for your ‘33 Plym sometime later. 🥴

[@oldbiker9739]

looking good .

[@dvljet]

Brian you forgot to mention that the 2k clear coat cant be saved once mixed so for that small a repair and the amount used its almost like wasting a $40 can of clear coat . unless your doing a door panel or a semi large area your going to end up throwing out maybe half a can of clear coat because after i think its 24 to 48 hours the left over clear is useless and hard and 2k is available at napa auto parts also brian is best to find a company like roberts paintcare who will mix you the exact paint colour if you give them the year the make the model they then show you all the colours and codes for the car or the other way is look for the paint code . i know online you can find a drawing of a car and it lists every car maker and where each place their paint codes .

[@born2wrench]

Etching primer is it good on rusted \sanded to bare metal panels????

[@a666n]

Great job but it would be helpful to know what temperature and humidity you're working in to get good results.

[@PaintSociety]

80 f

[@emanollucas2553]

I wanna know what size air compressor do I need to begin painting? I have a 2000 civic and wanna paint it but don’t know what size compressor to get

[@steve_hall]

Fabulous video, thanks for this. I have an 2011 Acura with clear coat failing on the roof... have any videos on this? Can I scratch it up and 2k clear over it to patch it up for a few more years or does it need to come all the way down to paint, primer, or even bare metal?

[@PaintSociety]

Check out my video list. I have older Videos on this and how to make it look better with out crazy painting

[@andyhoran2661]

What polish are you using?

[@Haider_Malik]

Top job thank you 👌🏽