DIY Powerful Ultra Bass Amplifier Z44N MosFet, No IC, Simple circuit

[@technicaldiy]

*DIY Powerful Ultra Bass Amplifier SSD Computer , No IC , Simple Circuit* kzbin.info/www/bejne/hoexY5ynjdtoocksi=jPtXuJCVo-xog2hT

[@JoseGonzalez-m8j9w]

Oye y si kiero k levanté unas 4 bocinas d esas omas grandes Sele ponen más integrados d audio

[@shahdevice3086]

ooooOOOOO SSSSuuuummm dude !!!!! Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not .. But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ... But people told that kid , that his idea was not implementable ...

[@edgararturogarciaportillo3799]

Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛

[@misterioznicoveculjak6461]

hahhahahahhhhaa 4,5? 1w max

[@FederacionFunk]

Hola, y como se calcula la ganancia de este circuito?

[@kumarsizhayat-r7y]

Hesap çok iyi

[@qddk9545]

I am sure that it is at least 10,000 watts 🙂

[@luispirela1128]

Edgar y como se hace si quiero colocarle otro speaker ? gracias

[@alexanderkuhn2298]

Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”

[@cyberhiper]

This is a Class A amplifier, output is approx. 2.5w with 12v power supply.

[@yourethebest7345]

That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that

[@westelaudio943]

There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.

[@gordonwelcher9598]

He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?

[@Uraim]

@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.

[@Uraim]

@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.

[@oorkruiser]

This is more like art than electronic achievement

[@finochachalaco7688]

No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊

[@shahdevice3086]

Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing

[@awalelectronicsburewala]

kzbin.info/www/bejne/fnjXgJmvn7eWf80 watch video about Ak amp

[@Uraim]

no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.

[@alexanderkuhn2298]

If you are interesting in electrical engineering do yourself a favor and dont watch these videos, there are much more credible sources elsewhere

[@mypopcorn8858]

Galing na man salamat sa pag share ng talent mo bro

[@subutayozselanikli]

Try to use F-CK69 Gaetanium transistor, it will give 10.000W or how much you want. Don't forget to use Shitanium filter caps for output.

[@nodriveasusephotos8019]

what are the filter caps for?

[@Matrix...777]

🤣😂🤣😂🤣

[@jesusrios7977]

Jajajajaja

[@esmeraldaguadalupeperezher403]

Excelente,pero vieras metido la bocina en una base o una cubeta de agua para ver que tal el sonido encerrado.saludos desde Campeche,Mexico

[@davpro1792]

That's like 1 watts at maximum, 1300w would blow that speaker it would be bottoming out really hard smoke and blow, lol

[@cucusupriatna3928]

Rangkaiannya Keren Banget.. hanya saja kalau kita mau Menambah Potensio sebagai Penambah pengaturannya bagaimana Merakitnya..? ok Terimakasih atas Konten nya, Keren Banget jadi Menambah ILMU.. ☺👌👍

[@gilbertovilchis7686]

GRANDE GRANDE GRANDE, MARAVILLOSA APORTACION PARA EL MUNDO,GRACIAS.

[@InventableESPT]

Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda

[@JoseRamirez-xc9dg]

Una pregunta.... la caja azul es una batería y de que capacidad

[@locuragamersclub6942]

@@JoseRamirez-xc9dg es 12 v es la batería que usan las alarma

[@tamirathailu8101]

Excellent!!! your are making an advertising for Microsoft surface too!

[@ИгорьШеремьев]

Я в детстве тоже усилители собирал,только маркер тогда ещё не был в ссср,а так бы я нарисовал ,что у меня динамик10гигаватт

[@sumner407]

What ever happened to good old schematics and parts lists? It would nice to include a shot of the circuit for us old school guys. Nice video though!

[@joorsoerowirjo7700]

I like these simple designs....very easy to build for beginners. But 1300watts with a single fet from a 12v battery.....that's impossible.

[@awalelectronicsburewala]

Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai kzbin.info/www/bejne/fnjXgJmvn7eWf80

[@jinkazuyatvlogs9332]

Just try and you can tell💪

[@gordonwelcher9598]

He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?

[@fortinomedinamartinez228]

GRACIOSO,,, sale la polilla por abajo del discipador justo cuando arranca el riser or filter de la música del video 🤣

[@LuiguiGamer1]

En la caja de descripción pude observar por lo menos 2 mentiras: 1300W y Hi-RES. Haces buen trabajo creando pero por otro lado no mientas.

[@jorgecontreras7631]

Si si es verdad, lo le dije son 1300 Watts de consumo, va ni eso, 1300 Watts RMS jamás puede ser 😀👍

[@Noalaagenda2030Marioneta-jf1jw]

Excelente saludos desde Metán Salta Argentina

[@syariefhelmi9709]

what voltage and watts do you use as a power supply?

[@completeselular3501]

Batrainya berapa volt

[@suhermancogreg8343]

Mantaaap bang.bisa buat jual di pasaran ni..di toko toko udh ada blm bang hasil karya nya

[@engineerkohat]

Great work. So much views. 1300W is not a joke.

[@kennmossman8701]

use Ohms Law it is IMPOSSIBLE here to get 13000W

[@CristianoVakisswinnerBarros]

Done is more than the perfection!

[@tonywalman]

With this single ended drive, the max power output can be easily predicted by the supply voltage and speaker impedance....

[@tronetrickard7130]

Can i use this circuits for boost dc volt?

[@westelaudio943]

There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.

[@Juniorfinger999]

Kembali lagi sperti biasa, ini ter kongkrit bagus jleger bom.. wow amazing

[@milenbuinov384]

this small speaker is 50w and this amplifier is 20w max

[@あなたはここで何を見たいですか]

Не 50,а 5-10 от силы но чуйка возможно не плохая😅

[@milenbuinov384]

@@あなたはここで何を見たいですか 10w speaker is printed. on magnet

[@paolbackman651]

You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)

[@あなたはここで何を見たいですか]

Мужики,вы меня дурите😄

[@johnangel1512]

@@paolbackman651 anyone can write 500W on a speaker, more likely a 10w speaker, freeze video where he's waving the speaker about 6min.50s

[@fairuzparman9888]

I’m glad if u can fix the speaker on box. So everyone can hear the bass far better

[@ricardojuarez291]

And not just that if the title of the video is in English at least and English song as well..

[@fairuzparman9888]

@@ricardojuarez291 yup. More enjoyable the diy project.

[@olinos4461]

Hahahahah Don't be fooled guys. that thing he claims to be a battery has a bluetooth player inside. The audio is actually coming from the media player inside the fake battery. Look at his connections, the red terminal in connected directly to one side of the speaker and the other terminal to the mosfet which I suspect has a short circuit ot the resistor connected to the mosfet case has a short or a wire was put through it to complete the circuit via the heat sink.. Also check when he puts the fake battery down you can see that it is light weight. I would have expected a battery of that side must have some weight . All his videos are fake.

[@demigi01]

that's true ! wires are directly to speaker, we all can see at 8:00 thank's for hint !

[@ash0787]

nice lol, I thought it was legit until he wires the audio out to both sides of the power resistor, couldn't see how that would achieve anything.

[@luisdamianduran2744]

Tengo todo el material pero en verdad funciona?no quiero perder el tiempo

[@Uraim]

@@ash0787 lolw, mine is under construction :)))) i use 5kg transformer :)) at 20volts :)))

[@dreadwings3]

I can test this arrangement with some caveat. So that there was audio output I had to connect the drain from the mosfet to the gate through the 10K resistor. Instead of connecting gate to source. The result was not 1300 W. I think it was much less than the speaker used 8 ohm for 60 W. The mosfet gets very hot.

[@arnaldooliveira7627]

É pelo menos neste esquema eu estou vendo a fonte de alimentação, porque teve um outro vídeo com tipo 122 e 127 , mais um triponte que não mostrava entrada da alimentação. Vc esta de parabéns.

[@زكيزكي-ر7ل]

God work. ..and easily to make. .thankfully

[@bongpenafiel1386]

Ang galing mo talaga idol gawa mo ako nyan

[@thomaswomack3888]

while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!

[@gordonwelcher9598]

He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?

[@juliusortaleza1486]

1300PMPO possible 😅 lol

[@mihaipaun836]

Cred că depinde mult și tensiunea de intrare ( semnal )

[@oberst_krass]

​@@juliusortaleza1486in PMPO everything is possible.🤷🏻👍🏼

[@abahaly8214]

1300w PMPO

[@imanudin6653]

Mantab terimakasih atas ilmunya semoga sehat selalu aamiin. Bang

[@prprojetos9726]

Congratulations blessed ball show stays with God hugs

[@Suavache]

Mạch công suất âm thanh bé mà khỏe phết của nhà nhỉ

[@chathucreations5176]

How much is the output watt ? How much power and Ampier should I give?

[@starmakercoversongs5186]

1000000v or fack

[@pujiononono7559]

wah praktis ,menggelegar basnya 👍

[@rsehaber]

1.300w? Or 13w?

[@sltrickshow3048]

13 w 😁😁😁😂😂

[@waik0182]

This amplifier delivers only 8w

[@irawardmusic]

Has anyone tried this? I would imagine that the battery is 12v and probably 10Ah. I would like to see him runs a voltage test on the battery to show us that there is no amp inside it. I will try this in the near future and get back to you.

[@ГеннадийМ-ь9ш]

Hello, I wanted to ask you, have you assembled a circuit, does it work, how many amps does it consume?

[@irawardmusic]

@@ГеннадийМ-ь9ш Hi, thanks for reaching out. No I haven't had the time but I will let you know how it goes. Thanks!

[@ГеннадийМ-ь9ш]

@@irawardmusic thank you, I will wait for an answer from you!

[@wlsnpndrvs8593]

Wtf? My Peavey Max amplifier had 24, 150 w Darlington power transistors in it, and it was 400 Watts per channel RMS.

[@alexyamazaqui5451]

Bro excelente video y q bien. Explicado gracias pero tengo una duda si aguanta trabajar la bocina con ese circuito bastante tiempo o solo es x un tiempo determinado

[@huracantornado1779]

SON CIRCUITOS EXPERIMENTALES NO AGUANTAN PARA LARGOS PERIODOS DE AUDIO.YO SOY ARMADOR DE AMPLIFICADORES DE SONIDO.

[@ibnurulyanto1218]

Can use potensio for increas or dicreas?

[@umyrizieq6272]

Biayanya berat di batrai dan sepekernya bang, sudah mendekati harga barang jadi. Sekarang salon bloetoet harga 300 ribu sudah bisa karaoke.

[@joelmathew373]

Can you make a video for making amp for using guitars pls

[@melvinvillafuerte1784]

Its all make possible in terms of materials circuit, but who knows were at long last it is, it depend on .

[@amitdhasmana1988]

How would you remove humming sound while conducting to transformer Ac-to-Dc ?

[@CreativeTechos]

Simple tested solution Connect 1uf poly cap between audio input + and ground.

[@joaoalves2281]

Legal gostei joaoalves

[@alexejditz2553]

Ребят когда он показывает динамик посмотрите там 10 ватт 8 ом😂

[@xolaniwiseman619]

I LIKE THIS AMPLIFIER MOST CAN I MAKE IT AT HOME

[@natalinoviana]

Será que pode usar uma fonte de 12volts ao invés da bateria?

[@ramos3246]

Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta. Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante. Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.

[@smartchoiceassistenciatecn4721]

@@ramos3246 será que vira testar em um carro?

[@micasaveiro]

essa bateria é de 12volt 12 amperes

[@วิเชียรวงคํามี-ศ6จ]

ขอบคุณครับ. หาของเจ๋งๆมาให้เล่น เบสสุดยอด

[@richardndikumana2970]

Est ce que cet amplie na pas de parasites!????

[@oorkruiser]

Impressive for such a simple circuit

[@oorkruiser]

Glad you found an amp to go with your 500W speaker

[@danyvillanueva3446]

muy buen video bien esplicado me gusta la electronica y me gustaria aprender

[@kilo_alfa]

Beau travail, merci pour le partage. Félicitations du Maroc 🇲🇦🇲🇦🇲🇦

[@marcoscapote587]

cara gostei muito, só que a ligação do falante está invertida né? batendo pra dentro , o certo é para fora

[@rogeriojesus7544]

Esse alto falante ai 500w😏

[@karantechnicalproject6473]

Nice video sir 👍🏻👍🏻👌👌👌👌👍🏻👍🏻

[@wilsonbell3516]

4.36 из под радиатора выбегает таракан аудиофил))))

[@juancarlosperezmagallanes6358]

😂

[@mugiyantofti7065]

Mantap, tp g dijelaskan pasang mosfet ke heatsink perlu isolator apa g, & besaran voltase ACCUNE jg g dijelaskan

[@rhs106]

Cara!meus cinseros parabéns pela excelente qualidade do seu vídeo. Parabéns!!!!

[@maryjaneevadiamond6359]

max power on that part is 110 watts, so fudging just a tad on the claims, but that's still a good build. Also keep in mind that your wattage shrinks as you are not using it at it's optimum voltage, it's rated to be used up to 55v and 49amps so your wattage is still extremely shy of the 110 max watts.

[@westelaudio943]

Max. dissipation of the FET does not equal output power. The latter would be more along the lines of

[@LakhwinderSingh-gx7jk]

Sir, please make this circuit in the supply of three faces please

[@pierpa_76pierpaolo]

@ Technical DIY How can you say 1300 W? But are we sure? What calculation did you apply?

[@miguelluizgiacomelli3250]

Bom mas esse padrão Rabo Quente na saída, acaba por distorcer os médios. Tenho vários projetos assim e se não for instalado um bom filtro, distorce mesmo.

[@josuealves-pregoeirodecristo]

Como fazer o filtro com potenciômetro?

[@roderickmuaka9583]

C'est impossible, mais possible pour vous, je vous aime et je vous remercie 🙏🙏

[@williammelo880]

Mas, valeu o vídeo, me lembrando aqui qdo trabalhava na ind.eletronica, eu fabricava as placas de circuitos impresso.

[@amanpandey9562]

What u have used in the end ..that something similar like iron plate

[@Yoyo-me]

Hmmm... Really very powerful... Had that thing measured 5watts? Unbelievable... Even the laws of Ohm and power formulas are not what they have been 😳😳😳😂😂😂

[@gordonwelcher9598]

He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?

[@mikephillips5551]

Your preview thumbnail was a click bait Showing a tower speaker with your DIY amp!! Thought we was going to hear how it really sounds!!

[@edmilsonrodrigues7734]

Gostei 👏 parabéns ficou show de bola 👏 obrigado.

[@clarelight8292]

It can obviously lift a large speaker because it uses a 12v 12ohm electric bike dry battery and of all the components it shows the size except the battery.

Excelente, buena calidad de sonido. Muy económica y eficiente.

[@manu-06]

neeee este video es muy falso

[@juliopena2336]

@@manu-06 porque???

[@manu-06]

@@juliopena2336 no existe un amplificador clase a con 1300 watts ._. Este proyecto a lo mucho 12w

[@juliopena2336]

@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada. Es de lógico que ese circuito no puede dar tan alta potencia. Gracias

[@warjitowarjito949]

Dah nyoba gak bisa keluar suaranya

[@aripsupriatna1574]

👍👍👍 saya punya amplifier merk sunbuck suaranya normal tapi ada gak yang suaranya ada kresek2 itu apa nya ya Om 🙏

[@kleyfram8792]

Parece ser tão simples de fazer

[@music_and_legend]

Achei a música que o @mw informática usa kakkakakak parabéns pelo vídeo

[@ОлегАнтонов-ь2р]

От 12 вольт как то попахивает вранье

[@МаркПьянков-в3п]

Да неа, вполне рабочий вариант. Только качества звука желает лучшего

[@ЕленаВаракина-в3ц]

При 12 вольтах? 1300 ? КПД-1000%-прорыв в физике,понятно,что у них другой "ГОСТ".

[@hugohernandez2289]

excellent video I see what you do congratulations hand up

[@ribeirotecnico7180]

Projeto muito bom gostei Nossa passou uma barata? Rs

[@Gans_G]

Siiii, también la ví

[@roninstrumen]

Mantap ide kreatifnya bang👍

[@АндрейЕмельянов-ж6с]

улыбнулся)))

[@Саша-л4ж7ч]

Бред какой то?

[@АндрейЕмельянов-ж6с]

@@Саша-л4ж7ч рофл!)))

[@chaihlaprumarma4471]

ওয়াও বিউটিফুল

[@carloszambrano3227]

Excelente amplificador, gracias..!

[@luisdamianduran2744]

Ati te funcionó??

[@carloszambrano3227]

@@luisdamianduran2744 Saludos, aun no lo he armado aunque tengo todos los componentes.

[@manu-06]

@@carloszambrano3227 noooo bro no te da 1300w A lo mucho 10

[@carloszambrano3227]

@@manu-06 eso es correcto, no más de 10w.

[@manu-06]

@@carloszambrano3227 ci y además un amplificador clase a no puede pasar los 30w

[@naseemahmad5832]

Amazing video

[@robertoloyola1639]

fala sério nunca daria essa potência toda..

[@kingedtz4522]

Kkk né isso kkk

[@adrianocordeiro8643]

Deve ser esses cara que fazem os mini-Sistem das casas brazoca hj em dia kkkkk. Consomem 10w e reproduz 1300w

[@kingedtz4522]

@@adrianocordeiro8643 kkkkk Nem classe D com 90% de aproveitamento kkk

[@kutingtingph]

Good job friend 😁👍👍

[@Juniorfinger999]

Spk nya 500watt brpa in bang ?

[@Learnelectronics738]

Great you video amplifier small

[@djmarosim]

RMS 5W? :-)

[@AllGearsk8]

Esta en avalancha toda la potencia se va al parlante pero de seguro se te quema facil necesitan mucha proteccion a no ser que tengas bocinas de sobra

[@mohammad.alinejad139]

سلام دوست خوبم ، بسیار عالی ، لطفا یک مدار سویچینگ در مورد تبدیل برق ۲۲۰ ولت به ۱۲ ولت با جریان ۱۰ امپر اموزش بدهید ، خیلی ساده با کمک ماسفت و چاپر

[@НиколайВасильченко-т7ц]

4:36 от девайса отделилась деталь и убежала . Если бы не убежала мощность была бы 13000W . 😄😄😄

[@Руслан-т7н8з]

китайских Chines 99999999 WATT

[@ВасяВасечкин-к4щ]

Какой-то лютый треш😂😂😂

[@RMCAZE]

Просто убираем нолики и тогда по честноку всё будет))

[@ЕленаВаракина-в3ц]

13 Ватт с КНИ-10%.

[@Андрей-э6э5г]

Это тараканы разбегаются

[@jshsshshhssuu6078]

Sir please add circuit diagram in your tutorial video, thank you

[@forropezadomaninhodostecla7014]

Vc tem o layout desse projetinho?????

[@lariontt]

Классный музон💥🔊🥁🎶

[@djedbrasil9019]

Congratulations... excelent!!!!!

[@BintangSenapan]

Mantap karya nya bg

[@filosofiabotequim]

Total RMS 15 watts

[@kennmossman8701]

much less than 6 Watts

[@akhemp2481]

Amazing kali

[@billimacompositorbl6574]

Muito massa...ganhou mais um inscrito 👏👏👏👏👏

[@rajneshkumarrajnesh9557]

Agar yah savan to dikha rahe hain aap vah bajega nahin to