DIY Powerful Ultra Bass Amplifier BTL C5200 , Transformer , Simple Circuit

[@technicaldiy]

*New idea:* kzbin.info/www/bejne/jmivYo2VhqZ-b68si=CiVIgMm3IGbQHzq5

[@levieux1137]

It would be better if you didn't claim absurd numbers. 3800W out of 12V is 316 amps. Not only your thin red&black wire would instantly bust into fumes, but even the transistors wouldn't stand it. The 2SC5200 is max 15A, i.e.max 180W with your schematic. Also you wired the jack in reverse polarity, and your two resistors are connected in parallel. And based on the wire size it looks like what you connected the transistors to was in fact the 220V primary, and the speaker is connected to the 12V secondary. This is a UPS transformer designed to work as a full bridge. There's not necessarily anything wrong with the final assembly as long as it does the job for you (i.e. make lots of noise), but you wrote a lot of errors and are inducing your readers into making errors.

[@annycell7500]

Jika terjadi short pada transistor, akan menyebabkan HP anda mati. Karena input audio tanpa melewati kapasitor kopling . Respect untuk kreatifitas anda,

[@Happikitty1.11]

Mksdnya hp mati hp nya bakal rusak?

[@technicaldiy]

it will damage the type C headset wire first and the phone will not be damaged

[@cibikoi6824]

Inputnya ganti blutut bang,, JD aman 🙊🙊🤪🤪

[@royrogers7644]

The circuit does not work. You cannot make the speaker swing in both directions with two pairs of NPN 2SC5200 output transistors without a phaseinverter. The real amplifier is inside the batterybox. The only point with these videos is to get clicks and earn money.

[@villageviewsofficial99]

Hi Brother @All Digital Craft

[@jawadranjha6083]

Are you sure that there's a real amplifier exists?? 🤣🤣

[@royrogers7644]

@@jawadranjha6083 yes :)

[@1lt3r]

You right Man 👍💯

[@Midnight_Philosopher009]

And fun fact is can see the output and input terminals of that transformer?!!! why 220V wires need to that thicker and 12 0 12v wires is literally way more slimmer as equal to nothing.

[@gafurjabborov9524]

🎉Оддий усулда моно усилитель 🎉🎉 ажойиб видео учун катта рахмат Гафур бобо 🎉🎉🎉🎉🎉🎉

[@Tatitzaldie-bm1po]

Walang siraan..kapwa kayo pilipino..Ang ibang lahi bumati pa Ng congratulation..Pinoy talaga kahit saan mapanira sa kapwa Pinoy..

[@electronicshelpcare]

2sc5200 is the best transistor

[@guinaldo29]

Aparentemente tem ligações erradas e/ou valores fakes tanto no falante como no transformador. mas existe essa possibilidade de usar transformadores nas saídas dos AMPs. mas não com essa ligação. mas tem que testar para ver se funciona. Valeu por compartilhar.

[@wackenroader]

Ele basicamente fez um amplificador tipo booster, nos anos 90 esse tipo de amplificador era o padrão no mercado de baixo custo, tinha tojo ab200, stetsom cl500, aquarius by faitron (hoje banda)

[@gafurjabborov9524]

Одну канале усилитель 24 вольт 25. Ват Моно большое спасибо за хорошие видео понравился

[@technicaldiy]

thank u

[@rairen-c7h]

yes I gave one thumb up, very creative

[@Richard-m3o]

cool greetings from Brazil

[@Organda]

Thank you master this is amazing and awesome projeck👍👍👍

[@madanraj9275]

Veri naic your teknic you geat brother I'm madan raj Indian

[@Panaev-Skabichevsky]

Трансформаторная развязка 🙂 лучшая защита от пробоя транзисторов. Прекрасный ролик, лайк однозначно.

[@колек-т6б]

интересно будет такой усилитель работать модулятором для кв передатчика на транзисторах ?

[@terrokturok9873]

Да ты тролль ))) А ничего что обезьяна, даже не читала Datasheet? И пара транзюков, естественно комплементарная ))) Да они скорее всего, уже пробитые. Учитывая что выковыряла обезьяна их, из старого БП.

[@ИванычМо-к6й]

@@колек-т6б всё можно. если хочется. но работать не будет

[@ANUBIS-l6m]

У этих транзисторов третяя ножка эмиттер , а первая база . Это даже как мультивибратор работать не будет .

[@raracheldanazzam4863]

Seperti rangkaian radio2 jaman dulu yang masih menggunakan travo primer dan sekunder

[@jafrikancarbon1234]

Man that 2500w speaker is hilarious af 😂🤣😂😆

[@mauriciorogel3846]

saludos desde EL SALVADOR buen video.

[@shahulhameedn953]

Excellent bro 👌👌💞💞💞💞💞

[@technicaldiy]

Thank you

[@Zilongofficial5678]

It,s a output not 2500w buts a 200w 👍👍👍👍👍

[@technicaldiy]

i actually tried it with 2500 watts speaker and it works fine

[@Zilongofficial5678]

It,s watt a speaker 2500w 1ohm yes

[@broccolixxx]

2500 is the pmpo while 200 is the rms

[@NandakumarJNair32]

@@broccolixxx - Correct.

[@derekfreeman3562]

@@Zilongofficial5678 is it capable of the 1ohm load,it'll fry your amp if not...does it get hot to the touch,or dam that's hot,after long..just wondering

[@suryaelektronikrepairs]

Fery good,superbass amplifier from trafo ups👍

[@technicaldiy]

Yes, this transformer from APC UPS

[@ARLIYT]

Wahh keren pingin buat dechh. 😂😂😂

[@gordonwelcher9598]

I do not believe the speaker is connected to a 220 volt winding. If the transformer is as labeled, the secondary 12-0-12 would be thicker than the 220 primary. It is the opposite. The primary winding labeled 220 has excessively thick copper leads. The label on the transformer is not correct.

[@saouga53]

1 ohm at secondar is a short .

[@kartrok3072]

@@saouga53 This device works. And it's inventive. This is what it looks like

[@KneppaH]

The handwritten powerrating on the back of the speaker is also a lie. He does it on more videos.

[@АндрейА-ш1ъ]

He just welding details randomly on each video) slow down, it's not working, he is just a fat troll)

[@warungseger2056]

i don't believe usb charger plug has changed to a sound jack 😅😅

[@gegersopian3413]

Waw. Keren. Ultra. Baas. Ini. Suara. Nya. Nyaring. Mantul. Mantap❤❤❤

[@SunilKumar-me4cs]

Circuit shown will not work. Audio In is connected with ground( ie :- transistor base is grounded).. Also why 2 nos 10k resistors given parallel from same trace..?

[@technicaldiy]

resistors connected in parallel to double the power

[@amazinggrace1598]

Yah he soldered the input hot wore to the negative

[@ЬюЬ-л5ь]

1) Трансформатор не рассчитан на 3800W 2) 2SC5200 по документам выдерживает максимум 150W 3) Для получения большой мощности от 12В необходим преобразователь напряжения 4) Нет усилителя напряжения 5) Схема вообще не должна заработать. Это чистый развод! Если начертить схему этого "чуда", то вообще смешно становится. Например чтобы получить нормальных 25W с TDA2050 нужно запитать ее двухполяркой 20V.

[@alirahimi966]

Very nice and good. Good luck

[@technicaldiy]

thanks

[@mamatmamat9212]

Luar biasa kreen sangat jenius kreativitas tinggi ,,,

[@Genivaldopereiradossantos-c5q]

Cara, Voce é bom demais. Parabéns

[@KadipiroJogja-ct5us]

Mantap bagus .dari indonesia terima kasih vidionya.

[@OXYMSC]

Pernah coba??? Nyala???

[@Kritsada_ST]

Wow..Music thai..Red Rose🎉🎉

[@andrzejdomalski4730]

Chyba raczej na głośniki się obniża napięcie, żeby uzyskać większe natężenie prądu. Przy zasilaniu 12 V, w tym podłączeniu transformatora, licząc straty, idzie na głośnik około 200.v. Nie będę tego próbował zrobić, ale wątpię czy to zagra.

[@morphinah100]

Tradus ai!!! entra 12v DC e sai a frequencia mais 12 AC que é normal para esses amplificadores antigos classe A. Dai so falta o pre-amplificador para filtragens, ampliar o som, definir a qualidade,limite de volume !!!

[@fiqfirdaus3180]

Greetings from Bosnia-Herzegovina 🙋‍♂️🤝...Don't worry, it won't burn unless you burn it, I tried it successfully, it was very satisfactory after I added a volume regulator and replaced the battery to adjustable 12v adapter👍🌟🌟🌟🌟⏯️...

[@muhammadramzanelectronics1956]

Very good 👍👍👍👍👍👍

[@solrac7986]

Very nice. But please install one Bluetooth on it, then it would be fantastic. But be careful, you are sending direct power to speaker, it will burn out, on hi volume.

[@technicaldiy]

yep, I will improve in the next videos

[@SherwinRamirez-g3s]

Ang galing naman more power po

[@chuongdo7098]

Trong như clip của anh thợ điện....nhận định từ bàn tay và móng cắt sát...

[@quiha567]

Thì là kênh của nó chứ ai

[@BrunoHenrique-rh1vk]

Tem que usa toda potência do Alto falante por ele pra pular até queimar kkkkkkkkk aí sim e brabo , mas fico toop brabo esse trabalho da hora

[@josevivanco7126]

Si funciona comprobado, la onda se amplia, a eso nos referimos a la frecuencia.

[@dariofamadulan5090]

Inside of the the battery is the main amp.. and the audio is connected with Bluetooth😂

[@donquijote2005]

Estas cerca, observa bien el video y verás una corneta bluetooh amplificada en un trípode colocada del lado izquierdo del video

[@HD-wh5de]

If you put some hot glue between transistors and radiator, you get up to 45Kw

[@joshuahboucher5628]

Now that's a cool class-A amp, can you make a high quality, 1,000 watt RMS Class-D mono-block, and a separate 2 channel, 2,000 watt RMS (1,000 watts each channel) Class-D amplifiers????

[@birumudajambi]

Untuk amplifier TOA masjid cocok banget itu..."

[@shaileshaluminiumsmvwork]

Very very nice . Bro

[@electronicshelpcare]

Thinks for this video

[@edivaldonache2312]

Aí sim valeu Agora Tem bastante potência 👍👍👍

[@RockRoseTribute]

Lo hice y funciona a la perfección! 😂

[@nenao1556]

You dont short circuit with the 2 way audio in, like show in your vídeo. Risk of damage to áudio equipament linked to your "amplifier"

[@pramokum6285]

Better to connect 240 volt directly to the sub woofer and trying to connect with your phone. Surely you will feel the dance bar with fog and louder music😋😋😋😋

[@nava-kit]

audio input wires left right connecting to negative wire ??

[@oswaldoayarroyo2082]

Tá tudo errado este capacitor não é de 2.5 micro......é de 2.2 micro o de 2.5 tá escrito nele 255..

[@desmondharney1185]

What did you record the final music with !. Thumping bass in the open air with no baffle

[@utjiesugiarto6070]

Sebenarnya. Banyak perangkat yang di buat China. Hampir semua kit. Ada. Sudah bagus murah dan mudah. Merakitnya. Hasil ok punya cuy.. Saya dulu sering buat. Sekarang sudah bosan. Banyak toko elektronik menyediakan. Kit. Yang cakep dan ok. Punya. Murah meriah dan jossss

[@angrybirds2472]

a power transformer for the output ? whats the ohms coming out of that load

[@Anusak09channel]

12/12 is AC or DC power thank you

[@gilbertoferreiradonascimen9482]

AC alternating -12 0 +12.

[@zaldyculaway8680]

yan ang gusto ko sa nag di diy di gaaya ng iba fake ang mga gawa.

[@andresgregoriocolancastill9644]

Exelente.... pero me confundí...es AC?????…gracias por su respuesta... Saludos.

[@technicaldiy]

AC

[@otakatik869]

Amplifier topology inverter

[@jefrikalisman]

very smart. look at pain hand. 👍

[@linusfran]

Pls describe what type of amp is this..looks like an attempt to turn 12 dc to 240vac stepup voltage booster into an audio amp which is ridiculous ,it simply doesn't have the current to push large 8ohm speaker well

[@ImamFaerozi]

Bisa di tiru brooo

[@jp3585]

🌹100 WATTS RMS💯💯👍👍👍

[@munir715]

love u dear

[@ahmadshareef7643]

رائع ممكن تستخدم محولات عدد 2 وسماعات عدد 2 لصنع الستريو

[@MrAlvarado62]

MUY INTEREZANTE ESTE PROYECTO Y MUY SENCILLO YO TENGO VARIOS MOSFET 38N30 Y QUISIERA FABRICAR UN AMPLIFICADOR CON ELLOS PERO NO EH PODIDO ENCONTRAR UN MODELO PARA YO REALIZARLO SI USTED ME PUEDE AYUDAR LE ESTARE MUY AGRADECIDO

[@DiegoEzequiel9]

El vídeo es falso la mayoría son falsos 8:46 ah se puede ver cómo tiene el Bluetooth activado el amplificador es la batería si quiere hacer un amplificador con mofets busque el diagrama por internet no crea en estos video gracias

[@Centar1964]

This would work better if the speaker was connected across the 2 12v windings instead of the 220v one...and just leave the 220v unconnected, connecting to the 220v side is loading the amp down way too much and you are losing power. Doing this and running into 1 ohm you could get up to 200 watts RMS with a 12 volt supply (assuming the transistors can take the current)

[@mariettadaogas7441]

Can you make a demo for it, really need it to enhance my TV audio tnx much.

[@v1los]

And assuming you have a Power Supply capable of supplying ~16 Amps! which lets face it, most wont!

[@Jao3677]

The thing is he made a booster amplifier instead a normal amplifier that's why he use transformer awesome..

[@Jefferson_Primera]

💯 Excellent 💥

[@lindarivera767]

Wow galing naman po

[@salvadorgarcia7224]

Thanks for sharing your ideas, I can try to do it.

[@ВалерийБеликов-щ1н]

The cool my friend.. Cool.

[@olxzender]

It's barely 11PM and KZbin already took me to the Twilight Zone Dude, this was nauseating to watch, but amusing nonetheless :D

[@channelamburadul]

Waow the best brow i like

[@wesley810]

Cara isso não é um alto falante de 2500 watts nunca, primeiro pelo tamanho do conjunto magnético, e segundo todos os vídeos que você faz, você nunca deixa o adesivo original do alto falante, sempre tira as informações do alto falante, e vem e escreve a mão a quantidade de watts que quiser no alto falante e quarto , podem reparar é sempre o mesmo alto falante velho e sujo, nunca é um bom alto falante cone seco ou borrachudo.

[@fiqiaprnsyah]

Min, can I use a 12 volt adapter to play?

[@technicaldiy]

Yes. You can use 12v from adapter

[@AuraIsmatu-fe4yg]

So good my brother

[@1MINTSHORTS]

Real amplifier circuit in the battery box🤣🤣

[@anybasssadanarchy8312]

😂😂😂😂😂😂😂😂😂😂😂

[@andercryptor3267]

Hey bro, this system doesn't burn the speaker?? Because from what I understand the transformer is playing 220v on the speaker, isn't that dangerous??

[@dieguimxloko4166]

Ok, onde tá o ultra Bass 3800w?. Nem se for 3800watt de pico, e se é ultra Bass pq tem tanta voz?. Te desafio à fazer um vídeo real!

[@wahyugandhung]

An AMAZING work 😊👍

[@SSGINFORTEC]

Super top demais parabéns 👏👏👏

[@patriciorenanvargasparedes3104]

Saludos de chile te quedó muy bueno felicidades

[@eddyirianto7953]

what's speaker impedancy 😀

[@technicaldiy]

1 ohm

[@vanlongnguyen2379]

Có lan can huyền thoại mới nhận ra anh thợ điện

[@technicaldiy]

haha anh thợ điện nhiều kênh lắm. có khi xem bác xem video của em nhiều rồi nhưng không biết là em làm đấy

[@royal.india.enggwork]

VERY GOOD THANKS FOR KNOWLEDGE SIR YOU ARE RIYALI GREAT THANKS AGAIN HARE KRISHNA HARI BOL

[@trioid6034]

is the transistor hot or not?

[@akku.azhicode6804]

Very interesting vedio thanyou somuch

[@somethingmore5621]

Thanks for sharing this video,your creations are good,but there's No volume control.♥️👍

[@technicaldiy]

yep, I will improve in the next videos

[@kuldipsinghjaswal1988]

Good

[@rommixvlog8879]

Booster sir lang yan

[@rafaelpatino8410]

POR FAVOR SRES DE BRICOLAJE TECNICO; YO HICE UN CIRCUITO IGUAL A ESTE DE 3800 W PERO LE PUSE EL AUDIO Y NO SUENA NO HAY SALIDA DE AUDIO: SI ME INFORMAN QUE PUEDO HACER PARA SACAR LA SALIDA DE AUDIO SE LOS AGRADECERÍA GRACIAS

[@averbisadverbera]

Los grigos ai artriba dicen q ese circuito es mentira, no funciona.

[@warungmiesetan7520]

Ok succes friend

[@suminto6733]

Mantep bos ngebas banget ya

[@bobbysese529]

good and simple amplifier circuit. but without any form of crossover or tone control, it will be fullrange, not a bass amp.

[@technicaldiy]

Just add a Bass equalizer and it becomes an ultra bass amplifier

[@davidhamm5626]

The input signal is where you choose that.

[@albinohilarioquispe4929]

Brigadier. J g vincule :-) URI yo Ojeda TFT y

[@ronaldyadao4145]

booster type amplifier

[@satishk8532]

He was controlling the volume through his mobile.

[@warungseger2056]

I can't believe the USB charger plug has changed to a sound jack

[@BeatriznsoniGomes]

Good. Gostei mas quero tambem 42 volt e de mais transitor.

[@roylabadan3303]

Its a booster not audio amplifier False theory

[@josemiguelabasolo5312]

Schematics?

[@karyostang3690]

Good luck friend Thank friend Please sharing diagram skema

[@YaninGonzález-s5l]

Bueno, bueno, en realidad no se nada de electrónica, me parece que lo hizo bien, por las vibraciones qué tenía la bocina creo que lo intentaré, si sale algo parecido lo aplaudire y si no , ni modo no lo veo más aaaa a los que opinaron qué estaba mal😂😂 hagan uno y así aprendemos todos fue un trabajo limpio y casi perfecto ( hay que ver si funciona) 😂😂😂

[@ddvan5947]

this is a brilliant idea

[@bars475]

Ang cute ng finger love mo ah

[@duylinhtruong7043]

Có chuyển bluotube đc ko và tăng giảm âm lượng chổ nào ko thấy giới thiệu ? Cổng kết nối USB chổ nào ? Cổng dùng điện thế 220V được ko ? Nhiều thắc mắc khác nửa .

[@helioalvespereirapereira2996]

Muitos aqui estão falando mal do projeto que vai queimar o celular que o amplificador esta dentro da caixa da bateria entao por que nao envia o esquema certo para o projeto funcinar direito este que estao falando mal nem sabe o que um diodo e fica falando msl do projeto dos outros em vez de sjudar.

[@joelfuertes8315]

Ayos ah.

[@hendribabuvaraprasad5532]

Super bro

[@puritygentallan7522]

Ok nabah🙋