DIY Powerful Ultra Bass Audio Amplifier Using 2SC5200 and 2SA1943 / Output Capacitors

Hi everyone, this video how to make an amplifier stereo using transistors 2SC 5200 and 2SA1943, the power supply is 12V/1.5A to 3A and this circuit uses capacitors at the output so it is very safe for the speakers. Thank you all for watching the video and don't forget to support me by subscribing to the channel so that you don't miss the latest videos. Good luck
Subscribers my channel: / @sharetechcreative
Amplifier using:
🔹2SC5200 Transistors x 1
🔹2SA1943 Transistors x 1
🔹100K resistors x 1
🔹10 Ohm/10W or 20W resistors x 1
🔹220uf/16v capacitors x 1
🔹4700uf/10v capacitors x 1
🔹50k potentiometer x 1
🔹Power Jack DC x 1
🔹12v / 1A to 3A DC adapter x 1
🔹Aluminum heat sink x 1
🔹Insulation pads silicone mica x 2
🔹3.5mm phone jack
-----------------------------------------------------------------------
➤ Copyright © by Share Tech Creative
➤ Thanks for watching my video
➤ Follow me:
www.youtube.co...
➤ Follow Facebook:
bit.ly/3eEHjNb
---------------------------------------------------------------------
****Video you may not have watched****
*DIY Class A Amplifier Using C5200 Transistor Extremely Powerful:
• DIY Class A Amplifier ...
*Diy Simple Three Transistor Class-AB Audio Amplifier:
• Diy Simple Three Trans...
*How to Make Simple Amplifier With Transistor PNP, Dual Speakers Connect:
• How to Make Simple Amp...
*Diy Amplifier Extreme Powerful Bass With Quad Transistors 2SA1943:
• Diy Amplifier Extreme ...
*Diy Amplifier Circuit Using Transistors 13007 From The Old Computer Power Supply:
• Diy Amplifier Quad 130...
*DIY Class A Amplifier 2SC5200 Transistor Extremely Powerful Using Output Capacitors:
• DIY Powerful Ultra Bas...
*DIY Amplifier simple 2SA1943 and 2SC5200 Transistor Extremely Powerful Using Output Capacitors:
• DIY Amplifier simple 2...
*How to Build 30W Mono Amplifier With IC NE5532:
• DIY 50W Mono Amplifier...
*DIY Amplifier Class A Stereo Extremely Powerful Using Output Capacitors: • DIY Amplifier Class A ...
*Diy Amplifier Stereo Class A Extremely Powerful Using Transistor H1061 Output Capacitors:
• Diy Amplifier Stereo C...
*DIY Amplifier Darlington 2N3055 Transistor Extremely powerful Using Output Capacitors:
• DIY Amplifier Darlingt...
-----------------------------------------------------------------------
Diagram circuit: photos.app.goo...
#diy​
#amplifier​
#ultrabass
#sharetechcreative

[@ShareTechCreative]

The video Heavy Bass Amplifier STEREO With C5200 and A1943 Transistor, the output capacitor kzbin.info/www/bejne/jYbUhZeNZ61_fdE

[@refaq3432]

sound quality isnt very good.. did i connect something wrong or my speakers cant do this job hahah

[@wahyunusantoroaji3448]

DIY Powerful Ultra Bass Audio Amplifier Using 2SC5200 and 2SA1943 _ Output Capacitors Hoax saya bikin sama persis ngk jadi

[@ShareTechCreative]

@@wahyunusantoroaji3448 Maaf! Aku tak tahu apa yang kau bicarakan?

[@ignaciovaladez2192]

De cuantos watts y cuantos 0hm. Es exactamente amigo

[@ignaciovaladez2192]

Y que bosinas le puedo conectar ay xfa gracias

[@luisdanielvlogs0108]

NAPAKA GALING MO SHARE TECH CREATIVE MARAMING SALAMAT SA PAG SHARE NG IYONG AMPLIFIER ALAM KO KAYA MO NILAGAYAN RESISTOR NA 10ohms 10 watts at Capacitor ay para MAPADAAN ANG AC SIGNAL AT ANG DC AY MAI BLOCK KASI KUNG CAPACITOR LANG ANG ILALAGAY MO DIYAN HINDI YAN GAGANA DAHIL SA ELECTROLYTIC CAPACITOR SANA TOTOO ANG IYONG GINAWANG AMPLIFIER GAGAWA DIN AKO NG GANYAN. SALAMAT!

[@ObserveNotify]

Ok that's right, I've already approved the bass it delivers. Great. Thanks.

[@ShareTechCreative]

Great!

[@Dago02]

No no funciona

[@TheTwinsDay]

First here and Always give Full View to others, you're so talented... so proud of you,thank you for sharing this awesome tutorial and tips, Have a great day

[@ShareTechCreative]

The Twins Day Thank you very much

[@TheTwinsDay]

I shared your channel with my friends! Thank you for sharing with us

[@severinonazario1570]

Muito bom obrigado Eu gostei de mais da quele esquema valeu boa noite Amigo

[@severinonazario1570]

@@TheTwinsDay beleza parabéns

[@misnadicn7738]

Terima kasih banget sdh berbagi ilmu. Selama di amalkan pahala tetap mengalir.. sukses selalu bro smg + rejeki

[@ΜΑΡΚΟΣΠΑΠΑΤΣΙΚΟΥΡΑΣ]

Excellent tutorial works great, i used it at my car with 12v relay for a small woofer and im happy with the result.

[@solucionestecnicastotal1142]

I hope to do for my car too. It's work ok with your batery, any problem??

[@thekillerdog5228]

Works as it should! Very low volume on phone compare to using on the pc, so my thoery is to build a pre amp first then apply this circuit ?

[@hobbysangjagat8547]

DIY POWERFULL ULTRA BASS audio sound system Elektronik lovers...💝 Good job brother 👌👌👌❤️❤️❤️ New friend here,,, Sty connneccteddd....

[@edgarcaldera5339]

Muy bueno

[@casel-ocanaldasucataeletronica]

I am Brazilian! And I don't know how to speak English. And with this I am in contact with you, through the google translator. You can answer me in English even if I see it here.

[@adrianberrio8605]

Hello friend good tutorial my question is.. the amplifier serves for the increase and decrease of volume ?

[@bambang747]

Ok juga.... tapi menurut pendapat ku mendingan untuk tegangan plus ditaruh menuju speaker,sebab kalau kedua tegangan(plus minus) ditaruh di kaki transistor maka transistor akan panas sekali,apalagi tanpa elco dan resistor sebelum tegangan masuk ke transistor.Kalau sy pakai elco dan resistor sebelum arus masuk ke plus dan minusnya...transistor jadi lebih adem...kalau seperti itu maka transistor tidak bekerja secara bersamaan(merata satu dan lainnya)apalagi bila pakai paralel lebih dari satu set.Sekedar sharing"aja dan berbagi pengalaman.mksh

[@utnhuttv2665]

Very good my friend helo good morning

[@ernestorangel7479]

Son muy buenos los vídeos, pero no entiendo porque la mayoría de canales de electrónica no suben sus contenidos más completos, por ejemplo, decir cuántos parlantes o bocinas se les pueden incluir a los amplificadores que hacen, o los parlantes de cuántos ohmios se le puede agregar al amplificador, siempre hacen un amplificador, y lo prueban con un solo parlante, o con una sola bocina. Si la idea es que uno, que no tiene conocimiento alguno de electrónica, pues uno así se animaría a hacer un amplificador con solo ver lo que hacen, lo digo porque tengo dos parlante de 8 ohmios, y cada parlante tiene su Twitter y subbufer, los quiero aprovechar ya que están en buen estado, gracias por tus vídeos, repito son muy buenos, saludos desde Colombia,

[@jaimerodriguezp502]

Ese sonido sonido se escucha tal cual siempre y cuando la bocina o parlante este instalado en cajon o caja para su respectiva acustica .....hay bafle oculto??

[@unmundotv]

Amigo ya estoy terminando el cable naranja al conectarle el voltaje es negativo cierto??

[@judsonbaker4628]

How many watts does it actually produce 5 to 10

[@ShareTechCreative]

More than 10 watts

Ultra Bass sound good👍good job

[@sonygare]

Como lograron que suene bien? Yo conecte dos bocinas LG DE 6 homs y no se escucha el ultra Bass algo que me recomiende hacer o modificar?

[@outdoorlifethailand]

👍L 👍 I 👍 K 👍 E 👌 for you my friend

[@ShareTechCreative]

ไต๋แขก โชคกิตติพงษ์ Thanks my friend

[@vojtab.6014]

Finally somebody who understands it a little bit because when I see those from indie plugging the loudspeaker into a short circuit and I always get upset, but your video is good, just kind of like it, try push pull connection it's class AB amplifier, try to find channel [DIY elektronika] i'm Czech but it does not matter you can look there do amplifier 2x 15w and you can look at the diagram what I use, but for your video I give you like because you understand electronics 😉

[@AndresBonifacio470]

I have plan to make this but i want to use 19V 1.58A so that it can give more power. What do i need to change in the circuit?

[@tarnicasper4632]

As the circuit only gives 8.784watts rms into unknown speaker ohmage at most likely 4 ohm at 12.2v at 19v it'll only give around 12watts and you'll need to use 25v capacitors.Amps are not applied they are drawn, at 19v the amperage will be around 1 amp

[@marcinwitkowski2981]

Great U learn probobly hard way. after burning speaker od DC :_) good wideo but unfortunetly power depends on big Resistor. Have u heard about push pull ?

[@ShareTechCreative]

Thanks for the tips!

[@nomer63078]

Can I substitute B100k potentiometer just incase if B50K potentiometer is not available. What is the output power of your project?

[@ShareTechCreative]

Yes, can

[@nomer63078]

@@ShareTechCreative thank you

[@praveenkumar-bw6km]

Aapki iss video me aapne kis brand ka smart phone use kiya he batao plese👆

[@casel-ocanaldasucataeletronica]

Good night my friend!! Good. Let me ask you a question. How much WRMS is integrated by this system there ?? Ie. What is the output power of this amplifier.

[@ShareTechCreative]

Amplifier class A, the RMS power is very low. Thank you for your visit and support

[@casel-ocanaldasucataeletronica]

@@ShareTechCreative ok

[@tigeratboarder4928]

Please mention How much output sound will come ( Sound watts ) . How much cost will go for this board without 12v Transformer and speakers.

[@penghiburpratama5765]

Mantap bos.rapih👍👍

[@ShareTechCreative]

Thanks

[@mohdirwan5114]

i have successfully it.it's amazing.thank you very big sir.😘👍🏻

[@ShareTechCreative]

Great job 😊

[@unmundotv]

Gracias me funciono a la perfección, una pregunta si le agrego mas voltaje aunque sea 20v sonaría mas, y no se quemaría los transistor??? espero tu respuesta

[@davidalvarez7967]

Amigo con cuanto lo alimentaste ? , he visto que le menten fuentes de 18v sin problemas ya rectificado sube como a 22

[@Lolo-nn4cl]

this is what i looking for. nice job with good speaker

[@aiysahchannel1113]

Wah bagus skali power amplifier 5200, dan bassnya mantap bang, salam siratuh rahim dari saya.

[@hungngo2182]

cảm ơn bạn , quá đơn giản mà hay .

[@sarai_yt7964]

La excelencia es hacer lo apropiado oportunamente bien hecho gracias mil Rafael Díaz rep dom

[@isurumadushanka9060]

can i use it for car battery power supply

[@ShareTechCreative]

Can't be used for cars because it consumes a lot of power

[@esdraspereira.s7486]

Muito bom seu amplificador. Vou fazer um desse. Parabéns pelo seu trabalho

[@hafizulizham8692]

Hello sir...if I make two set like this..can I combine both make one set stereo sir?

[@ShareTechCreative]

Yes, absolutely

[@hafizulizham8692]

TQ sir...you are good man👍🏽

[@Marianoliva1984]

Es muy bueno el video lo voy a probar, se puede hacer con mas potencia con 2 o 3 pares de transistores?, saludos

[@ShareTechCreative]

¡No mi amigo! hace mucho calor

[@lethaoconhac2377]

Gioi quá .hay tuyet voi luon nè

[@clecioricardo3129]

Gostei Amigo Eu Tenho um Que eu Fiz mais Depois Eu vou Fazer um Desse Parabéns Pelo o Projeto Ficou Muito Bom

[@YantoKriwilMiri]

Good job bos ☺👍👍

[@ShareTechCreative]

Thanks 👍

[@sugatu7uhtujuh44]

Can use 24V or more ???

[@ShareTechCreative]

Can not

[@sterlingmmattiaputty1035]

Itu berapa volt om bisa pake batre gk?

[@ShareTechCreative]

This circuit uses 12 volts, you can use Battery, but be careful as it drains a lot of power.

[@puriwatw.1323]

I have issue with humming noise when turn on the amplifier. What should I do to reduce it?

[@ShareTechCreative]

There are many types of noise, I do not know what kind of encounter you have if the hum frequency 50hz-60hz is due to the supply of electricity is not clean. If the noise when you touch your hand, it becomes even louder than it is due to the input signal wire or the wrong ground (GND) ... and there are many causes of noise, please check and learn more. Thank you

[@tarnicasper4632]

To all you asking what wattage lets use ohms law to calculate shall we? before onset of clipping/distortion amperage read 0.72amp x 12.2v =8.784watts rms...not really enough?

[@elWieslaw]

Great philosophy.... Try to calculate such an amplifier and build it from individual discrete components. And this is not a cascading amplifier, but a real one, for example - push pull.... Connect two ready integrated circuits with several resistors and capacitors - every donkey can

[@Elelectricoandante]

me ha gustado mucho el proyecto

[@ricardorabelo3717]

Hello, what is the power in RMS of this amplifier? I have a JBL 265F-1 500w and 15 "woofer and would like an amplifier for him with 12v. I wanted the amplifier to be mono to use as a subwoofer in a system with two 50w satellites

[@severinonazario1570]

Muito bom gostei parabéns

[@severinonazario1570]

Eu gosto tambem anprificador com o saida de audio 2N 3055 ou tip 41a42 tá valeu

[@ShareTechCreative]

Thanks for the info!

[@jesusbuenomedina7784]

@@severinonazario1570 amigo tengo un Powel me suena ronco pero tiene buena potencia por ke será

[@bouzidoussama7546]

hello i need your help pls i tryed a lot of times making an amplifier with different transistor but its not working with mje 13009a and s30d4oc

[@ShareTechCreative]

How can I help you?

[@bouzidoussama7546]

@@ShareTechCreative thx you i need to know how can i calculate the resistor needed placed btw the base and the collector and i allso need to know how much needed in capacitor i dedja knowhow much voltage but in the uf its hard

[@bouzidoussama7546]

@@ShareTechCreative and what is the fonction of resistor in the transistor

[@daluz93]

hola, me sirve con transistores FP FN 1016 ????

[@ShareTechCreative]

Yes can

[@daluz93]

@@ShareTechCreative NO FUNCIONO XD

[@daluz93]

hola, muy bueno, ahora mi pregunta es si se puede hacer lo mismo con trancictores FN/FP1016

[@oscarsodano9931]

Yo estaba pensando lo mismo que tu ! ...tengo 2 pares de esos transistores dos negativos y dos positivos

[@mrinnovatorin]

What speakers can we connect to this amplifier?(in terms of watts and ohms)

[@ShareTechCreative]

Speakers 4 ohms to 8 ohms, 5 watts to 20 watts.

[@mrinnovatorin]

@@ShareTechCreative thanks 🙂

[@mrinnovatorin]

@@ShareTechCreative sir what would happen if we connect speakers with greater than 50W ? Will this circuit burn?

[@hijodelaltisimo777]

Excelente pero tienes el. Plano para fijarme?

[@jonasm.k.3502]

does it fit on speakers of either 4 ohms or 8 ohms? if you connect two of these cards in series to increase the power would work well ??

[@ShareTechCreative]

Can use 4 or 8 ohm

[@CHANNEL_HIBURAN-3]

Bang saya sdh rakit sesuai tutorial, dan suara bagus. Tp TR sangat panas meski sdh dipasang heatshink

[@ShareTechCreative]

Anda harus memisahkan heatsink untuk resistor. Terima kasih

[@CHANNEL_HIBURAN-3]

Bang power ini sy tambah tone control koq suara gk keras ya. Klw tanpa tc suara keras

[@victorhugogallegogalvez5210]

buenas es la misma coneccion para 2 trasistores 2sc5200 gracias

[@miguelguadamo]

Buenas, excelente videos amigo, una pregunta le puedo colocar un adaptador de corriente de 19v de una laptop que es el que tengo y que tendría que cambiar en el circuito?.

[@ShareTechCreative]

If the 19v dc power supply I recommend using this circuit, the sound is very good and the circuit is also simple: kzbin.info/www/bejne/eZ-lo6V6fNOqoqM

[@MayraHernandez-kl6ct]

Si puedes amigo únicamente tendrías que cambiar el capacitor por uno de almenos 25 vols

[@franciscojavierpinedamunoz2186]

Excelente video entendible por favor ayudame con esto como manejar el tema de los ohmios esn cado de querer un ampli estereo

[@sonmythobonsai904]

thích xem bạn làm điện tử

[@khairulanam6580]

Maaf ini bisa buat di tape mobil rumahan kah. Atau ada video lain buat di tape mobile rumahan. Tq

[@kinhnong1875]

Bác có nhận làm r bán lại ko. Chứ ra tiệm mua trở r tụ r các kiểu ít quá họ ko bán

[@cuocsong7ngay55]

I can use power 24v ?

[@ShareTechCreative]

No, only 12V

[@cuocsong7ngay55]

@@ShareTechCreative sc5200 max volt is 200v datasheet

[@creatifotodidak603]

Amazing,,,

[@ShareTechCreative]

Thank you! Cheers!

[@severinonazario8596]

Muito legal parabéns

[@ShareTechCreative]

Thanks

[@Sonidokayro]

good video, cuanta potencia rms da???

[@Nirmal83Singh]

why the 10w transistor is over heat. tell me what reason

[@ShareTechCreative]

You should use a separate heat sink for 10 Watt resistor

[@agozz783]

how many watts of speakers sir??

[@antonsupada]

Good job dear friend. Thank you very much for sharing your video.Have a nice weekend.

[@hrtech1284]

can i run vibe 900 watt peak power 300 watt rms sub woofer ?

[@silasfelipe854]

Gostei vou faser um tenho tenho todas as peca obrigado pela dica

[@GunkDeManaH]

bang, kira2 ini bbisa diaplikasikan ke mobil gak ya bang?

[@ShareTechCreative]

Itu menghabiskan banyak daya

[@hairolnizam1119]

Can i khow what power supply model and name u use

[@kvs8598]

Bro,How many watts does this amplifier get? Please reply

[@tarnicasper4632]

8.784watts rms

[@casel-ocanaldasucataeletronica]

Tá ai que gostei deste vidéo vc esta de nota mil !! Desculpas mas vou fazer o meu amplificador

[@joeyscott4299]

Excellent Work my friend ! I am gathering my parts to build this today ! Very nice design !!

[@joeyscott4299]

Thank you for sharing .

[@fatehsoda634]

زمن الفيديو طويل اشكرك

[@pietro19610]

Hello....e volndo usare o stesso circuito per altoparlanti largabanda quale sarebbe la modifica da fare al circuito???Aspetto fiduciosi tue notizie....Ciaooooooo

[@ShareTechCreative]

Probabilmente non è necessario cambiare il circuito

[@clintmurphy5436]

Very cool..

[@ShareTechCreative]

Clint Murphy Thanks, bro

[@alvarorudas6020]

Como se llama el reproductor que estas usabdo

[@ruddytaufik4973]

Resistor to power over heat why?

[@HECTOR60189]

Can I use It a mini subwoofer od 300W with that Amplifier???, good video my friend!!!

[@sonmytho9683]

bạn làm điện tử hay thật

[@youngvarenc6696]

kabel putih yg dispeaker min apa plus

[@mariobenavidez3868]

Amigo buenas tardes.que exelente trabajo la calidad del sonido es fuerte y nitido lo felizito. E visto muchos tutoriales es mas los e elaborado o los e ensamblado pero no e tenido exito.ahora e visto su exelente tutorial y lo hare y espero me quede con esa calidad de sonido.¿de cuantos whatt y ohms es el parlate de prueba que usted utilizo? Le agradecere su respuesta. Soy mario benavides. De nicaragua.gracias.

[@ardyferiyanto3946]

Mas mau tanya yg SC 5200 ditaruh knan ap d kiri itu mas

[@mauriliosilva2263]

Tem como bota um desses em uma dessas caixinhas via bluetooth

[@mdrazu6568]

100%working?

[@ShareTechCreative]

Yes

[@muradhusain7472]

i made today my 16v 4700uf/10v capacitor over heat and blown.why

[@ShareTechCreative]

Thank you for your info

[@marquinostequila_detector8905]

Disculpe amigo esta super su circuito, como se llama la canción de ssu ampli

[@smsonido]

Se llama Arpy - Dan Hening

[@yonaemanuel]

Why Transistors C5200 and A1943, must work together, and why A1943 itself cant make Amplifier on its own?

[@ShareTechCreative]

yona emanuel You're want to use one the transistor A1943 as an amplifier? Thanks for comments

[@yonaemanuel]

@@ShareTechCreative yes. I wanted to know why mostly they are used together c5200 and a1943. I thought one is for left channel and other for right chanel but at the end the amplifier is Mono

[@ElPrecursorAmargado]

Que potencia da este amplificador?

[@sugatu7uhtujuh44]

Klo transistor nya di ganti sanken bisa tidak?

[@ricardoarana5747]

Buen día Y a cuantos Watts de da por salida

[@lafaietesilveira6988]

O alto falante é De quantos ohms?

[@ShareTechCreative]

8 ohms

[@lafaietesilveira6988]

@@ShareTechCreative Ok, irei montar amanhã. Grato.

[@albertoalexanderuribevelaz7841]

cuantos watts, inpedancia de la bocina y el diagrama porfa

[@ShareTechCreative]

Please check Description

[@albertoalexanderuribevelaz7841]

@@ShareTechCreative ok, Í got it ty

[@nomer63078]

What is the power output of your project?

[@josegeovannytorresalava8914]

Cuantos was de salida tiene ?

[@DISCOTEQUEVANELY]

Estoy replicando ese ampli ahorita. Pero al subirle desde mi cel se escucha muy saturado y no se xq

[@westerntv8631]

Big like💪👍

[@ShareTechCreative]

Big thanks

[@NFOCraft]

출력 커패시터를 사용하는 DIY 강력한 울트라베이스 오디오 앰프 2SC5200 및 2SA1943+88

[@BustRadioMyths]

Would this be class A/B or class A?

[@awjk2051]

Muito bom aguenta até quantos volts ?

[@DJLAWOLF]

Check the description because I just said I think it's 12 volts