DIY Simple Short Wave Transmitter With XTAL Oscillator Steady Frequency

How To Make A Simple Short Wave Transmitter
If you have any question about this Short Wave Transmitter, please feel free to leave a comment, please like ,share & subscribe ! thank you !
Here is the circuit diagram:
drive.google.c...
P.S. The circuit diagram was designed by Stefan0719 , channel : / stefan0719
Music provided by spoti.fi/NCS
Music by Tobu
/ tobuofficial

[@kenf8563]

This short wave transmitter works well, just beware that if you follow the video step to step that the very first ceramic capacitor that is installed as per video is wrong. He notes that he’s installing the 104 ceramic capacitor when actually it’s the 332 ceramic capacitor that is installed first just after the first transistor you install. I notice this mistake as per schematic and everything else is correct. I installed an IC socket in place of the crystal so I could plug in various crystals frequencies. I used a 6 pin IC socket, cut it in half and then cut off the middle pin. I also used a stripped 20 gauge solid copper wire for the antenna. I’m using this for checking vintage restored broadcast/short wave receptions as per alignment instructions. Poor reception where I live so this solved my problem with checking the short wave band and I already had a AM and FM transmitter

[@dare-er7sw]

I've one AM Transmitter schematic. Wanna build it?

[@serginx]

Thanks a lot

[@panda315]

This sounds like amazing advice! I’m just beginning to learn this topic

[@Evilslayer73]

Hi where i connect the battery on the schematic?

[@kenf8563]

Positive from battery connector to positive of the 100uF capacitor. Negative from battery connector to the #332 ceramic capacitor which is also connected to the emitter of the transistor.@@Evilslayer73

[@ujandjajand8731]

I have made it like your circuit. I use a 3.7 v power and it works like a charm with clear sound quality. Thanks for your sharing.

[@jtfc67]

Works perfectly! Just be aware if you're assembling and watching the video. The first capacitor shown in the video is 3.3nF, not 100nF.

[@victorwando8950]

have you tried it ?

[@strongradio90.3fmkusganbac5]

Nice project DIY Shortwave Transmitter it works also to follow your schematic diagram i have use 12.00Mhz exactly transmitted i dont know what is the range in a few parts!

[@alfihry]

Simple & Great project .. thank you so much مشروع بسيط و جيد شكرا لك...

[@eletronicacaseira8843]

Ótimo projeto amigo, parabéns pela sua criatividade.

[@yitiksevda82]

Hi Stefan.What material do you use for sound output in a shortwave transmitter? Did you plug it into the microphone output of the computer? As far as I can see you are playing the youtube video. How do you establish the connection between the shortwave transmitter and the computer? What other material can be used for sound output in the shortwave transmitter circuit? I will be glad if you answer.

[@tomte2283]

Pretty late, but hes putting it in the earphone output, the one where you plug earphones or boxes in

[@ishtiaqkhan7101]

HE IS USING AN AUDIO OUTPUT JACK (RED AND WHITE PAIR WIRES), BUT IF YOU NEED TO USE THE MICROPHONE DIRECT TO THE CIRCUIT (TRANSMITTER)YOU NEED 1 ADDITIONAL TRANSISTOR-BASED PRE-AMPLIFIER, WHERE THE BASE OF THE TRANSISTOR WILL BE ATTACHED TO THE MIC WITH A 100K OHM RESTOR +V AND THE COLLECTOR WILL ATTACHED TO THE BASE OF THE 1ST TRANSISTOR .

[@macasusineiljohnc.1976]

​@@ishtiaqkhan7101 do u have a circuit diagram for that one? I'm working on a project exactly like that

[@Rtechs2255]

Can we use 12v adapter for vcc ?

[@Evilslayer73]

Very cool project!!

[@Evilslayer73]

Hi where i connect the battery on the schematics its not clear and the audio input ? :)can you tell me to which component they are connected? if i understand well the audio input goes to c4 and c3? im not an expert :)😅😉

[@MrErickpe]

Excelente! Fiz um com 27mhz.

[@victorwando8950]

can u share your circuit diagram please Did you use the same components in the video??

[@MrErickpe]

@@victorwando8950 Hello! I didn't use this video. It was another scheme, but this one in the video is better. I will do it and present it.

[@serginx]

Vou fazer um teste

[@arkhilious]

Totally bummed out cuz I don't have any capacitors under .22μF, meaning I don't have that last component. Hopefully I can scavenge one from something, cuz I am not yet old enough to buy things online.

[@ludwig8891]

Eine gute Sache

[@robotgillercom]

hello from microphone input to this transmitter. Can it be sent by superimposing a square wave or a sawtooth wave?

[@Killexexe]

Are we use bc 547

[@diyshow888]

Hi Killex , No, we use 2N3904 😊 , Regards

[@AABB-en4ps]

Hi，How powerful is it?

[@awaismushtaq5719]

At best 30 yards

[@ZephodBeeblebrox]

How would you adapt this to send CW (Morse)?

[@NetGeniusYT]

Sir network jammer pe video lawo kaise frequency ko kaam ya jayda karke network jamme kare .. Plz reply kijiye gaa

[@Arkliobybis]

Anyone tried it with 27mhz crystal?

[@mr.0x373]

i'd prefer higher fq's because you will need smaller antenna

[@TheSpinninHead]

Can we use the same crystal oscillator to generate variable frequency pulses?

[@OG_K9]

لا اعتقد ذلك لان المذبذب المتغير تختلف دائرته عن هذه الدائره

[@jadontechtv7711]

nice

[@eye1523]

distance kilometers broadcast area?

[@andressebassinga448]

Hi! Can you tell me how did you design your antenna? and what is the range of this transmitter?

[@manofmesopotamia7602]

how far this can transmit?

[@MrMinimum24]

best

[@diyshow888]

Thanks

[@Arkliobybis]

Did you use high voltage capacitors here?

[@diyshow888]

Hi GreenHat No high voltage capacitors used

[@varunmanchanda3972]

Can i use 16mhz crystal?

[@diyshow888]

Hi Varun Manchanda , yes , you can , the frequency will be 16000 KHz (16MHz)

[@aceswag3882]

@@diyshow888 thank you :)

[@firefox1136]

Thanks, this really helps!

[@user-uq2oe4dg3m]

Hello, how can we use a microphone instead of an audio jack? What changes should be made in the circuit, thank you

[@mouizeddinekisma4226]

check this video it covers that kzbin.info/www/bejne/nH6ph5ZqmJ2se5Y

[@andreabaldini7073]

hello how many milliwatts does the antenna circuit deliver? thank you

[@technodruid]

Calculate it

[@jsjsjjsud9556]

Around 1-10mW most likely.

[@TechInventorAman]

Hey i loved you content . Is it possible for you to make a receiver for the same ?

[@diyshow888]

Hi Tech Inventor Aman Maybe you can try TA7642 + LM386 😊

[@diyshow888]

theradioboard.com/rb/viewtopic.php?t=7136

[@diyshow888]

MK484

[@TechInventorAman]

@@diyshow888 But tell me something the transmitter you made works on frequency modulation right , even if its short wave its basically frequency modulated. But this receiver is meant to read AM . Then how will that work ? Also i loved your content buddy could you ping me at [e-mail] , i would be more than happy to chat with you

[@guillermomartinez942]

Por que no inscribe el diagrama ? O publica el diagrama porfavor

[@michelney2915]

How far can it transmit?

[@hixidom2274]

I can never get perf board to work but maybe I just have cheap perf board

[@Chems7308]

5:56 .the guy doesn't no idea that it work or not😂😂

[@aceswag3882]

Can I lower the crystal to 16khz so I can get a regular AM range? so its then AM not short wave? Cheers

[@diyshow888]

Hi ace swag LW, MW, SW are all AM ,you can give it a try :)

[@conghanhoang1222]

I wanna build this circuit but my input signal is Morse code, it is a digital signal. I don't know How to do it. Do you have some ideal?

[@elmjyl2907]

transfer morse code into beeps

[@victorwando8950]

can this work in a normal fm radio or its a must it be on showrt wave mode

[@diyshow888]

Hi @@victorwando8950 It's for short wave radio, if you want fm , please watch this video kzbin.info/www/bejne/fJLYd3acrpmdm68

[@geovaneomaior]

what is the transmission distance

[@analogmusicarchive6012]

What is the power output?

[@makroradio6836]

Sw radio am 2 wat 5 kilometer. kzbin.info/www/bejne/fHmseGVvlLeKn5o

[@technoartist4297]

Can we also make a receiver instead of using sw band

[@diyshow888]

I think the answer will be something like :"try to make a sw band radio " 😂

[@technoartist4297]

@@diyshow888 so then my question is how to make a sw band

[@sadboy3990]

How to make mobile segnal boostre?

[@videomusicalirariintv2412]

It's possible to buy one form you??????

[@diyshow888]

Hi Video Musicali Rari in Tv , Sorry , but you can simply build one if you have those components 😊

[@attilarivera]

Hi Q1 work as an audio pre-amplifier?

[@manofmesopotamia7602]

yes

[@JuarezWildner]

VER ESQUEMA DO PROGETO A ONDE

[@jemussi7842]

cct diagram?

[@refayamine7944]

Can you receive this crystal at a frequency 104 MHZ ?????????

[@xXTheoLinuxXx]

It doesn't have a filter, so yes every 8mhz has a weaker spot.

[@newcreation3411]

Can we use 2n2222 transistor and 1mf capacitors¿

[@diyshow888]

Hi New Creation , I didn't test 2n2222 , maybe you can give it a try 😊

[@newcreation3411]

@@diyshow888 thanks for your reply

[@newcreation3411]

@@diyshow888 can I ask you something? Are you on intagram I want to chat you on instagram

[@newcreation3411]

@@diyshow888 are you on intagrm I want to chat with you on it please😀😀 😀😀😀😀😀😀😀

[@diyshow888]

@@newcreation3411 Hi New Creation, sorry I have no instagram 😊

[@jsjsjjsud9556]

What is the power of this?

[@diyshow888]

It's 9V battery 😊

[@jsjsjjsud9556]

No I mean output power in mW.

[@beyondtheuniverse]

Don't this need a inductor ?

[@diyshow888]

Hi Byond Theunivers , As you can see , no inductor needed 😊

[@AndysRamblings]

Circuit diagram?

[@diyshow888]

Hi Andy , circuit diagram is in the description of the video.

[@AndysRamblings]

@@diyshow888 Thanks. I didn't click "Show More" before, but now I see it!

[@luisdavidsamanaherre5165]

Tengo un cristal de 4.000 funciona ? Help

[@Antenna101]

Yes

[@mohammedaneesx6833]

Use full content

[@ivan69420.]

Lol, but how ya know that freq.?

[@edyt4125]

The Quartz Oscillator was also 8MHz