DIY Solid state relay 12V

[@vk7hch]

I was always under the impression a relay (like you show at the beginning) used a small current to switch a large current. Your schematic shows a flasher unit, not a relay.

[@Sekhar_Home]

But it canot runs on led indicators

[@ShopperPlug]

Can this be used to switch AC loads?

[@chibuzoeze4225]

Is the mosfet drain connected to the right place? If yes, what about the connection of the load?

[@khurramshahzad2899]

Plse make the 2 way solid relay please.means normal close and normal open working use.

[@leviahamefula3994]

Are you sure you know what you are doing? Flashing circuit or relay?

[@anas2004]

Could it work as frequency base in an inverter circuit, ?? No problem if higher than 50hz ???

[@FabiusKadett]

It seems that the fuse and the lamp symbols are swapped. In this configuracion the N-Mosfet is being used as a HIGH END.

[@krlojaelarambula7646]

Buenas tardes, hola disculpa sabrás cómo puedo reemplazar un transistor para amplificador MN15N

[@MCsCreations]

Fantastic work, dude! Awesome! 😊

[@PaulJosephdeWerk]

How about a DIY mains voltage solid state relay?

[@johnfew5145]

Will this circuit work with an LED ?

[@TheJavaSync]

Can it always ON / OFF setting ?

[@agsolarpower5975]

Please make video on dead time in three phase half bridge

[@dismayer666]

Well, actually it's not a relay. It is a flasher circuit. You can't just swap this with a car flash relay. In a car a MCU usually pulls down the relay (+12V is always connected, MCU gives the negative) which turns the relay on. To create such SSR you need a P-channel MOSFET and some additional circuitry.

[@ShopperPlug]

This is a real SSR but depends on the context you are referring to. If you mean an AC load SSR... requires additional components and circuitry.

[@nirodper]

Is there a minimum lamp power consumption to make it stable? Would it switch ok with a low power led?

[@bobbelman6666]

Nicolás Rodriguez 4:49

[@LeonArdoDoV]

4:48

[@PhG1961]

Awesome ! I really enjoy watching your videos.

[@antonioinochi9170]

Could someone make a simulation with qucs of this circuit...I tried but without result

[@techs5564]

i will do it now. but tell me can i hook a 12v buzzer with the lamp in parallel? Will it burn the Mosfet?

[@sasodoma]

Tech Seeker You need to know the maximum current of your mosfet and the draw of the lamp + buzzer

[@techs5564]

Sašo Domadenik, yes you are right.

[@kpomalproductions5254]

Please please can you make a FM transmitter.

[@Wuety06]

pll

[@alexdelgado2192]

how can I make an on of relay

[@techs5564]

replace the R3 with a 50k preset, i hope that might work. Middle pin of the preset will goto the capacitor C2, last pin ground.

[@biplobpaul9906]

please making a video for subwoofer active LPF circuit use op amp

[@kougaz]

what is it for?

[@shaneclark5022]

very good as always. love this channel

[@kennmossman8701]

it is a Flasher, not a relay

[@maxxsmaxx1901]

Very useful circuit .Thank you

[@electronic7979]

Excellent

[@masterd1ffrence213]

Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan for mosfets used in circuit

[@MedSou]

Good Job👍👍👍

[@bassome3000ify]

Thank for clearly explaining

[@8elimA]

the great channel i love it :o

[@aryanxhan2248]

Superb dear,,

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan for mosfets used in circuit

[@eng_mustafa8717]

How adjastable speed Flash litght . please next video. This self circuit, .

[@techs5564]

yeah just change that capacitor value.

[@eng_mustafa8717]

Sorry I want to use these two that I can change time speed flash of the lamp using variable resistance control the time of the cut. ...... Thank you.

[@vladimirdudas9397]

Mustafa theking if you want changing blinking speed, than best option is use 555 timer. I can you draw complete schematic for this

[@AJRestoration]

Epic!

[@amirabdurraman6286]

Good proyec

[@DilnuwanAmaraweera]

Thanks this is nice

[@fidelinaaquino5270]

Con dimer to multimeter

[@electromagic3111]

Nice

[@MaxTim995747]

молодец!

[@masterd1ffrence213]

This video is greate !!!

[@james_robertson]

.

[@arpitjain4025]

Do u even know what is really and how it works??? u r calling this circuit as RELAY....seriously ???

[@cyrustakem7993]

Cool, but this isn't a solid state relay

[@PaulJosephdeWerk]

Agreed, it's a solid state flasher.

[@samraatshah4593]

why you always promote jlcPCB in your video😐 we are not bound to buy anything from there, always

[@arpitjain4025]

all these people got sold them selves to china

[@masterd1ffrence213]

Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan for mosfets used in circuit

[@kabandajamir9844]

So nice thanks

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan

[@masterd1ffrence213]

This video is greate !!! And Can u pl upload a diy of a 12v pwm circuit upto 30amp capabilty with a fuse and a fan