DIY STEERING WHEEL New EMC FIRMWARE

[@poptartheroes]

This firmware finally got my encoder working right! Thank you so much!

[@krishnakarma6166]

But did you got pro version?

[@CanArall]

did you find how to buy it? @@krishnakarma6166

[@cnoart4698]

Wow, increíble, muy buen trabajo!

[@thegrigs]

I have an old Microsoft Sidewinder FFB Wheel. Could this firmware work to make the setup of this wheel? Microsoft ha no uptaded config software for it.

[@-christian-2533]

Hey man, nice firmware! By following your steps I have that the motor response is absolutely violent even at minimum settings and driving is nearly impossible whatever the game :D

[@AgaYuditraStudio]

Mantap om... 👍👍👍

[@ebolzzable]

thanks om udah di promosiin wkwk

[@agungwibowo24]

Kl pake arduino mega bisa ga mas bos

[@lonewolfgaming584]

Great work!! I am simply amazed. Could you give a tutorial on how to programm it by yourself? I always wanted to learn this type of programming?!

[@jlae2]

Consulta, muchas gracias primero q nada, pero tengo problemas para poner las levas con un switch, donde podría ponerlas?

[@DavidsWorkshop]

Hello! I'm interested in buying the software but I don't have a FB account. Is there any other option to reach you?

[@canaldovacao12]

Congratulations EbolzMagy YOUR PROGRAM IS PERFECT. WE BRAZILIANS WE THANK YOU

[@ebolzzable]

for the lite version, it is not perfect ... spring effect is incorrect, sine effect is rough, inertial effect is mis directed ...

[@punkklan]

E aí vacão, está com a versão pro?

[@canaldovacao12]

@@punkklan, ainda não. Nem sei se ja saiu! Já?

[@canaldovacao12]

@@ebolzzable I'll buy the pro

[@punkklan]

@@canaldovacao12 basta fazer uma doação via PayPal. Recomendo muito a versão pro.

hi there! Is EMC software needs tunning every shut down of computer? or just tune on first run and plug and play?

[@botticelli2280]

Gran trabajo...espero ver mas trabajos. Gracias

[@eren4412]

Thank you so much. Last project my chinese encoder didn't work but with this program it's works.

[@trahka]

Which chinese encoder are you using? a 100ppr enconder?

[@eren4412]

@@trahka no, 400 or 600

[@trahka]

@@eren4412 You got it from a printer?

[@justsheeeps134]

Add 4.7k ohm resistor to a and b phase with 5v power input

[@adrianszczecinski6110]

@@justsheeeps134 but what resistor power?

[@ФедорДругов-ь1т]

Hey! please help me!!! Connected according to the scheme from the video as a result, the encoder reacts FFB does not work (((

[@kanaca]

Ini yg di tunggu2 siiiplah...

[@rivaldoluiz1164]

OLA COM POSSO BAIXAR A VERSÃO NOVA

[@motoanaliser]

hi. why use resistor? me work for no resistor

[@ignacywojtulewicz8005]

Hi, the EMC program that i downloaded from your google disk ins't working properly - firmware version is unknown. How can I fix that ?

[@alexanderschindler6999]

Great Work!

[@jason_tood4386]

Does this firmware support the CWZ1X omron encoder ?? please some help me.

[@kaciuu6744]

why upload is failed? i selected correct COM and i connect my arduino to usb...

[@khaleel96]

Wow! Thanks buddy for this firmware i was struggling with my ffb motor problems I install this followed your video & boom!!! everything works fine first time thanks man

[@ebolzzable]

Ok man...glad to hear that..

[@AdeAhmad]

Karya bapak bangsa... Mantabz mhank

[@ImTiui]

Hey, great work! I bought the encoder but the power supply is 8-24v, not 5v. Can i make the 12v from the switching power supply?

[@joaovictorschultz2970]

You say in the video description that there is support for 20 buttons (5x4) but in the Readme file and in practice only 16 (4x4) works. I look forward to work, for now I liked the result. It is responding very well, and the communication between the card and the pc is very fast and accurate. Congratulations.

[@ebolzzable]

Thanks...new update use multiple hbridge conections,so i need to reduce matrix pins

[@foxxyytofficial]

The 0.93 version in the video supports 20 buttons (5x4), the 0.932 supports only 16 (4x4) because EbolzMagy created more support to other H-bridges than only the BTS7960, and that needed one of the pins used by the button matrix

[@ebolzzable]

In latest version (ver 1.00) i added I2c conection for buttons...so we can create 64buttons...

[@joaovictorschultz2970]

@@ebolzzable good work, but ver 0.932. not work whith Game Stock Car extreme. I don't know if is a problem on game or EMC software... I need pro version, RFR is bugged where. I'm waiting for the next version. (Excuse me for english)

[@modellerdesign]

@@joaovictorschultz2970 try rotate the wheel 90 deg both derections, while loading the game, or a ride.

[@okb00mer80]

Do this firmware support inkjet rotary encoder?

[@jureknez4816]

EMC works fine but it's looks like arduino leonardo don't output PWM power. Please for help

[@kevinwang8874]

at 2:09, what is an xy shifter?

[@modellerdesign]

Superb!!!

[@pch_mechanika]

Guys can any one tell me how do the ECM wheels compare to off the shelf ones in regards to force feedback fidelity ?

[@immax78]

Hi I have a problem. Games don't see the steering wheel! Everything is fine on the computer, the ems utility is working correctly, but when I enter the game, I cannot configure the controls. What could be the problem? Thank you in advance

[@cedricsawit2759]

are the 4x4 buttons are individual input buttons? i'm planing to use it as h shifter.

[@CVIDAL256]

Hi, congrats! BTW, what music is that one playing ?

[@suhendardiki5214]

Semoga sukses Bolz.. Team P1

[@ebolzzable]

Nya del...nuhun 👍

[@suhendardiki5214]

Nyieun video na sing rajin atuh

[@dekri7746]

Mantap jiwa om ebolz mah

[@movementexe8699]

so first i have instal xloader then dowloand EMC hex and instal this on arduino. And when i instal on arduino im oppen firmware and its work ?

[@0utj]

its cool, but how connect to driver L298N ?

[@MongooseTNM]

The wiring diagram doesn't work for 3 phase encoders. Could you update it to support 3 phase encoders?

[@zex_nos]

There its a way to use load cell for brake pedal? or only works with potentiometers?

[@ebolzzable]

U can use hall effect sensor...for load cell u need INA125P amplifier..

[@Vooseel]

I got 2 phase encoder from printer. At Ai-wave it's working like charm, but at EMC software doesnt detect any movement when spinning. All the wiring is like in the tutorial above. Do i have to get this omron encoder to make it work?

[@ebolzzable]

all photoelectric encoder has same work priciple so i think omron is overkill....for range below 10$ u can use chinese encoder,encoder printer,smart wheel encoder or diy encoder..

[@paraoalie2215]

How i use a micro switch for a handbrake?

[@Jibbsie-ru2iz]

this looks really good, what games dose it work with

[@yiimbob7805]

Is it really possible to use pins 0 and 1 for the encoder since they`re serial pins (RX and TX) ? And what`s the purpose of the two resistors between 5V and the encoder pins?

[@ebolzzable]

For omron or some chinese encoder the resistor function is only pull the signal,without resistor the arduino cant detect encoder movement,

[@yiimbob7805]

@@ebolzzable OK thank you . I used an optical encoder from a printer and it worked flawlessly without the resistors even on 3.3V :)

[@yiimbob7805]

@@ebolzzable do you recommend using some capacitors across the DC motor terminals (inductive voltage spikes) or is it save to operate one without this kind of protection (i am using the bts7960)

[@ebolzzable]

@@yiimbob7805 im using hitachi Do6 motor without capacitor,and only use ferrite magnet

[@JUANCHO-1114]

hola, cuando publicaras nuevo material? espero tus videos, gracias por compartir informacion, saludos

[@jcgesilva]

Good afternoon, I followed the wiring scheme of the buttons, but it did not work test pins 4 and 5 that would be a button did not work. Is something missing?

[@ebolzzable]

bit.ly/2T4q8xr on wiring folder

[@A.P.A.V]

can i use my vnh2sp30 h-bridge with thist firmware? how can i wire it? THANKS YOU

[@AM44]

in which pin of arduino to connect the Z axis of the encoder, in the new firmware?

[@ebolzzable]

This firmware didnt use z index because size of program will not fit..

[@mandziuc]

not working on rf2, need to do some configuration?

Hello how can i buy pro version?

[@boistenia5364]

With emc utility pro, can i change pwm frequency?

[@gauravumbarkar9141]

will forcefeedback work with vnh2sp30 motor driver ?

[@wally19]

I have the same issue with two boards. Im connecting only pedals, wheel and FFB. Sometimes works and sometimes not. Its like some other inputs needs info and makes others pins to fail. Is the sketch available? or what should i do? Thank guys! amazing job doing this.

[@tresh8568]

Good afternoon, and you can connect the 8 buttons, something I can not figure out?

[@ebolzzable]

You can see on wiring folder on gdrive,thanks

[@amarbabu7891]

How can i buy the pro version??? I tried to contact the guy but no response....

[@AM44]

02:09 which resistor?

[@ebolzzable]

220Ohm

[@sumitbarua8241]

Hi if i use EMC ,how will i connect a 3 phase encoder to the arduino board.please help with the wiring process

[@ebolzzable]

Emc only use 2 channel encoder,just connect Channel A and B only,thanks

[@simonegaido4541]

Hi, it could be possible to use EMC with a 130 st-10010 (20 nm motor)? I'm currently using it attached to a STM32F4 with MMOS but I'm searching for a more modern tool. Thanks a lot and congrats for yor great work!

[@billyjoel8673]

Thanks for your great job , are you going to add more effects : Ramp, SawtoothUp and SawtoothDown?

[@ebolzzable]

Flight controller??

[@billyjoel8673]

no a racing wheel , but i use arcade ffb plugin from Boomslang and with your firmware i have no reaction with this effects , but with RFR firmware there's

[@Zraner]

Where can i find the wiring set for the pedals? or where i can put the potenciometer for the pedals in arduino?

[@foxxyytofficial]

The pedas are really simple: the middle pin on the potentiometer can be connected in the pins A0, A1, A2 and A3 in the Arduino, the left pin GND and the right on 5V

[@pro5p3c7or1]

what is the difference between the pro and lite version?

[@febbyatigagaming]

Panutankoeh hahaha😎👍

[@Gonza46178]

hola gracias por compartir el proyecto, anda muy bien pero en assetto corsa en practica el force feedback no me funciona pero en race si, alguna idea. saludos desde argentina.

[@oscardiaz4701]

Working with Arduino Pro micro?

[@hahmetsurucu7127]

Hi mate! Why do you used resistors, and what happens if i dont use?

[@fregisz]

i I guess encoder signal need voltage pull up. If not, will be "no signal" from encoder. you can google "pull up resistor"

[@muharremsuz]

i use no resistors. ffb is soo strong impossible to control. but is it causes for resistors i dont know

[@sebsonexrexflex]

@EbolzMagy why you use resistor ? can you tell me?

[@ebolzzable]

just for pull the encoder signal,for omron and some chinese encoder the arduino cant detect the signal pulses

[@matej7627]

I have soft lock effect in Dirt rally 2.0 but no force feed back whats the problem?

[@ebolzzable]

You need add pid and vid in devices_devines.xml,you can see for guide in my gdrive

[@DundarPEKINER]

How do I get the EMC pro version?

[@afullmx]

you connected encoder and motor driver to the same 5v output on arduino. Isn't it a problem?

[@afullmx]

wasn't a problem 👍🏼

[@Juanchow8]

hi, i would like to get the pro version in a future, how could i do it?

[@vmgambiarra5511]

Mudar para português I connected the encoder and force feedback as in the EMC video and I connected the hshifter to the other ports but none recognize the buttons. what can it be?

[@ebolzzable]

for the lite version it doesn't support xyshifter, only 20button(matrix) .. for the wiring button you can see it on my gdrive

[@ale1898-ac]

Hello, one question, I would like to acquire the pro version of your software. And consult you if it is possible to use a load cell of 50kg + HX711 in arduino leonardo and using its tutorial and its software.

[@Javier-yd5qf]

Hola! Una consulta, donde se puede comprar la versión pro? Gracias

[@ale1898-ac]

@@Javier-yd5qf Consultales por facebook que ahi seguro te van a decir.

[@adamzdunio8190]

how can i have an access to emc utility pro?

[@plamemonolit5289]

I’m sorry, give me please full version of EMC, because I can not work in a lite version. Thank you so much my friend! :)

[@plamemonolit5289]

And I don’t know how to connect my h-shifter, because in wheel config I set the value of the micro switch, in EMC I don’t know how to connect my H-shifter. If you help me, I be very grateful.

[@ebolzzable]

@@plamemonolit5289 if the lite version is not work..then the full version will not work too...before go to full version you must make lite version works first...and im really sorry full version isnt free..thanks

[@plamemonolit5289]

No, problems give me say how much is full version, and how to connect my paddle switch? Because I rely don’t now how to connect 8 switch in EMC Thank you very much!

[@ebolzzable]

@@plamemonolit5289 same as lite use button matrix..contact me at [e-mail]

[@MrAndrjuha]

Give some link for this software please?

[@rivaldoluiz1164]

ola sou rivaldo como fasso para adidigueri a nova versão manda um cotado

[@josh_miller___]

my force feedback isnt working plz help

[@Giwrgos.S]

Nice job my friend keep on....i am trying to finish my diy wheel and i will take the pro version for sure ...but i have an issue... everything is good...i use my6812 100w 12v motor the bts and Arduino... when i go in wheel check the wheel runs very well but when i use other mods or if i go in assetto corsa the psu shut down after a second....i thought that is overload protection but i used an Amper meter and the psu shut down randomly in very low amperes....is that a psu issue or something in wiring? I hope that you have something in your mind Thank you for your time bro !

[@ebolzzable]

shut down if wheel have loaded?or when the wheel in spin?

[@Giwrgos.S]

Its ok now...it wasnt when the wheel was loaded.....it was when wheel changes the load fast ...from 6amp to zero and again ....the problem was the pc psu ...i think that it was a protection because the psu is ok in a pc....i bought a 180w psu and now is ok...i am trying to silver some issues and i will be ready.....

[@GreekSIMRACING]

@@Giwrgos.S Το έχεις ολοκληρώσει;Άρχισα ν το κάνω και εγω.

[@Giwrgos.S]

@@GreekSIMRACING ναι φίλε την τελείωσα αλλά πάλι στην άκρη είναι γτ κόπηκε ο ιμάντας περιμένω τώρα αλλο....γενικά όλα καλά αλλά πολύ μεγάλο θέμα η μετάδοση....κ το πρόβλημα είναι ότι για να πάρεις σωστή μετάδοση πρέπει να σώσεις κάνα 50ευρω...αλλά βαράει τελωνείο γτ Ελλάδα δεν θα βρεις τπτ....

[@GreekSIMRACING]

@@Giwrgos.S εδώ έχω κόλληση και εγώ πεταμένα λεφτά για μετάδοση άξονες κτλ.To προφίλ μου facebook.com/giannis.papapostolou1 στείλε μου PM να ανταλλάξουμε ιδέες και λύσεις

[@yigitdincel7148]

Can i use button matrix with emc lite or i have to use pro version?

[@ebolzzable]

lite use matrix mode,full version now use stm32 board

[@puresim316nosimracingnolif3]

Hi will your software work for a simucube mige wheel?

[@josebatista8981]

Bi bro! Can i use a closed loop stepper motor with this firmware?

[@gavinli4936]

Is there a way to connect this to a servo motor drive to make a direct drive wheel?

[@krigga9317]

so how we get the pro version I can't find any source to it, also does this work on arduino uno, or is it only those mentioned?

[@poptartheroes]

It only works the leonardo. You have to buy the pro version from him.

[@luisravelsilvaoliveira5226]

how do I buy the emc pro?

[@ebolzzable]

Go to emc fb page,link in description

[@tientran-yz3zn]

I am using WheelConfig 0.21 and I want to switch to EMC Pro, where should I start? Thanks

[@ebolzzable]

to protect my work isn't free my friend...contact me at [e-mail]

[@matei_dragos850]

Why euro truck sim 2 crash when i set tha controler for steering?

[@ebolzzable]

Delete global control sii in my document..

[@matei_dragos850]

@@ebolzzable I do this and it still doesnt works...(i have not install all cables, maybe because of that ? )

[@ebolzzable]

@@matei_dragos850 no ...because u installed aiwave before,the name is same as arduino leonardo but the descriptor is differ from my firmware...try clean install your ets bro..and delete ets data on my document folder..

[@matei_dragos850]

@@ebolzzable it not works :((((

[@foxxyytofficial]

Still with problems?

[@speedboy911]

the motor doesnt turn only the encoder is working

[@mehmetselim880]

you awesome

[@matej7627]

Its works thanks . Firmware in the Installation folder. Where can i pay for the pro version?

[@CanArall]

did you find it?

[@joeypurschel5124]

how can i get the pro version i have pay \pal

[@ricardosouza5026]

hello good morning i would like to have the pro version of emc as i can u help me in advance thanks !!!

[@betaris100]

hello friend ,, I made the donation ,, thanks!

[@ebolzzable]

Check your email my friend....thanks

[@betaris100]

@@ebolzzable hello my friend redo the donation with the correct value of 10 dollars, thanks!

[@ArtPowerStudio]

Belo projeto! quando será liberado o EMC 0.94 Features ?

[@revotrucksimulator]

What's up buddy? Is there another way for me to purchase the PRO version of EMC Utility other than through Facebook? Because I don't like to use facebook, I only use email? Thanks.

[@lovrospoljaric3488]

hey can i get the download link for the pro version

[@AM44]

@EbolzMagy How to get the PRO version of the program?

[@ebolzzable]

contact me [e-mail]

[@broken_props]

how do I get the pro ver

[@JulianMgil]

HI, How i can get the full version? Only Lite version in the link. Thank you.

[@muharremsuz]

dm him on facebook pace

[@betaris100]

How do I fix the version of emc rpo that supports xy shifter?

[@lucaolbc]

Hello dear friend, I tried to use your software. The first time, the ffb worked but was much heavy then I try to lower the ffb out and in the game and the ffb stopped work. I try to reinstall the firmware, clear eprom..etc and my ffb don't works anymore. Do you know what can be the problem? Conflict with other old software? (I had the WheelConfig and the Vjoy before) or Maybe my bts board is not working but I don't know how can I test my bts isolated to find the problem. Can you help me? The BTS visually don't seems fried but I don't know if it is working. (obs: the power supply, motor and wiring is okay)

[@Giwrgos.S]

Hi... did you try to cycle your wheel go to play again?

[@foxxyytofficial]

AiWave(WheelConfig) conflicts with EMC you need to get rid of some regedit keys left by WheelConfig firmware Search for the "Canal do Vacão" comment here

[@betaris100]

the .hex firmware file is not in the EMCLite folder. Could you make the file available again?

[@ebolzzable]

the .hex file located on EMCLite installation folder..thanks

[@ebolzzable]

the .hex file located on EMCLite installation folder..thanks

[@betaris100]

@@ebolzzable the only ex file in the EMCUtilitylite folder and this BareMinimum.hex I can not find what turns into joystic ,,, help me and please !!!

[@ebolzzable]

@@betaris100 install EMClite program first,and check EMCLite installed folder,the .hex file will available there

[@Harperr11]

I greet everything works well but in the game the steering wheel will not find what it has to do to make it visible in the game thanks

[@ebolzzable]

not all games support generic wheels, such as forza horizon and wrc series