Let's Try EMC On DIY Gaming Steering Wheel

[@d5tscript797]

5:49 I had same problem the solution is minimize the game and open the emc software turn the wheel upto 0 degree and we can add maximum 4 button in liye version so we can use paddle shifter or sequel shifter

[@d5tscript797]

We can use handbreak and clutch at same time there is an option for that

[@d5tscript797]

And one more before Manuel turning to centre turn off motor power supply😅

[@zudumalli]

Thanks, bro. I got it. I can see that his diagram connects the buttons to the GND - digital pins. so that's why I am saying we cannot use buttons through the lite version. but after you said that I would short the digital pins one by one then I found three useful buttons.

[@d5tscript797]

@@zudumalli you can use the 4 buttons are 2-5 and I cannot tell the connection because I am beginner in ardunio😶‍🌫 but there is video about it and the button never shows in lite software . It shown only in windows joystick control section. Your videos inspired me to create something thanks for your Tutorial ❤‍🔥

[@zudumalli]

Yes, I see. Thank you too

[@starkovigor27]

5:50 Let's allow a turn of the steering wheel of 900 degrees. This is due to the fact that the torque of the motor is not strong enough to stop the steering wheel in softlock (-450 ... +450 degrees). Because of this, it goes beyond the maximum degree of rotation of the steering wheel in one direction of degrees and then tries to return it to the extreme the value is 450, but again, due to the weight of the steering wheel itself, it begins to twist it already in the other direction and repeats itself.

[@zudumalli]

I don't think the torque is enough. But another thing happened, this truck turns off the engine and when using the wheel config, the wheel feels tight (realistically) but nothing happened in the EMC and after turning it about 50 degrees, it started spinning like in this video. This also happened with Assetto Corsa

[@starkovigor27]

@@zudumalli whats truck I don't get it

[@TechBabu801]

​@@zudumalli Same thing is happening with me

[@kristof3031]

@@starkovigor27 the truck in the game

[@jzayden]

Finally 🎉 I think can use more button in matrix, but can't use xy shifter.

[@anuhaskalpa]

Nice ❤️🔥

[@jscreations1040]

Supiri❤❤❤

[@adityaplayz03]

Hi if u connect all the wires from potentiometer ro controller then which wires are connected to pcb board in controller method please help

[@zudumalli]

Bro that video description has all the diagrams check it

[@adityaplayz03]

@@zudumalli it is not proper

[@adityaplayz03]

Which wires did u add in the pcb board and from where did u add

[@AbdülkerimYilmayan]

What is wrong with you man what do you mean by not proper? İts literally the easiest diagram to read you Need Basic electrical understanding man there Are far complexe Diagrams than this 😂

[@adityaplayz03]

@DarkRange-vw2pn then explain me bro which wires are connected to pcb board and from where

[@yagamingx2002]

Bro which is best wheel config or EMC ?? And what games does emc support?

[@yagamingx2002]

Hello bro how defferent wheel config or emc pro version

[@prakashprajapati1031]

Can i use 1k potentiometer instead of 10k??

[@RealRenko]

what is your editing software and voice over and i did have that problem it happen whenn the wheek goes over bumps so it ocelates so the sofware gets confused and tries to 0 it but it keeps failing so it spins the only way i found to fix it is to lower road viberation this happend in forza for me too when going over some rocks

[@zudumalli]

I use Premiere Pro and Google Cloud text-to-speech. yes, I also try different games. The same happened in assetto Corsa. but not every time.

[@coolbosplayz5318]

U can use the buttons there are 16 available

[@tibrewa6879]

can i use load cell instead of pots for pedals with this software?

[@zudumalli]

I think it is possible with the emc pro version

[@Nilanthiamarasingha-l5s]

❤❤❤❤❤❤❤

[@priyangaediriweera5807]

❤❤❤

[@ninjafrozr8809]

Does EMC Lite or Pro have support for analog joysticks ? I want to have joysticks on my wheel.

[@_Smoke_V_Okno_]

why can't my arduino Leonardo see the potentiometers on any of your firmware? What could be the problem?

[@zudumalli]

try resetting the calibration on game controller panel or check wiring

[@yagamingx2002]

will support h sifter?

[@justadamss1459]

Pro version does

[@RajWarudkar]

Hey there is a game called snowrunner can you explain how can we play snow runner with this steering wheel

[@aaditmartin2318]

Bro can you make a video on how to set wheel up using EMC pro

[@zudumalli]

Yes I will

[@robertogarciamtz8006]

Can you make a wheel with stm32 board?

[@user-vx8lo4sg8q]

My problem is that when I test with the wheels config program, my steering wheel keeps turning in one direction. Can you help analyze the cause?

[@21_luthfanakbar33]

mas saya pake encoder printer epson ip2770. tanpa ffb berjalan normal. tapi ketika saya nyalakan powersupply tidak terjadi apa apa (wiring 100% sama sdh bolak balik di check, motor pakai 775, psu 12v 20A) apakah ada saran atau solusi? terima kasih

[@DetrasDeLosVideos]

How can i configure My Sterling wheel EMC Lite with forza horizon 5 & show runner

[@zudumalli]

I haven't tried it yet, I will post a video about it

[@s4mimawon]

help me, I have followed the tutorial why in the wheel check application I tested the steering wheel doesn't move itself (in the game there is no vibration).

[@zudumalli]

check your wiring and resistors

[@s4mimawon]

@@zudumalli I've tried it and another problem arises, sometimes the steering wheel moves by itself and can't be controlled. please help thank you.

[@aaditmartin2318]

Bro to which pin on arduino board should I connect handbrake potentiometer

[@zudumalli]

A3

[@joseitod0553]

Hello bro, I made the connection as is from the BTS7960 to the motor driver, but the force feedback does not work for me

[@zudumalli]

did you check your motor driver and Arduino wiring (Arduino 10, 9, 8, pins)

[@joseitod0553]

@@zudumalli It was a bad encoder connection, it had pins A and B inverted, which is why the feedback did not activate.

[@umangikisanjali6171]

bro you can use gimx adapter

[@umangikisanjali6171]

GIMX BRO

[@zudumalli]

will see bro

[@makhilpranav6949]

Bro if i press brake pedal the accelerator also fluctuates in the software how to fix it pls?

[@zudumalli]

check your potentiometer wiring

[@mojokumzukatube7461]

my potentiometers fluctuates rapidly if i use smps but does not if i use laptop charger ...any ideas what could be the problem??

[@zudumalli]

Does your SMPS power supply have an earth wire? Check it is properly connected.

[@ertugrulbt]

I want to ask because you have been using it for a long time. Was the rs 775 motor enough for you? Were you able to solve the heating problem completely with the fan? Would you consider buying a larger dc motor?

[@rexycontemplates]

I would use 2x 550 motor instead

[@jzayden]

Use 895 motor for more torque , increase torque and decrease rpm with either gear or belt.

[@zudumalli]

honestly enough for me. but it depends on the power supply and weight of the steering wheel and its width. I use a 12v 20A power supply and a 300g Steering wheel. wheel width 10.5 Inch

[@mdwafiulalam3483]

i download emc but the xloader is not working and i use arduino uno

[@zudumalli]

this is not supported to uno devices

[@AIBYHANZZ]

Bro what is the error at end the same thing happen to me

[@zudumalli]

I didn't get it either

[@LuizChicareli]

Good afternoon! I built a similar sim wheel, but on the EMC utility lite software the steering is inverted. I tried inverting the encoder wires, it worked but the ffb went crazy. Do you know what can I do? I'm researching in the internet but i haven't found anything useful yet.

[@zudumalli]

try inverting the motor driver wire (10,9 pin)

[@Sam-kh1eo]

Do you have someone tutorial for loadcell and arduino ? some tips and tricks ? :D

[@zudumalli]

No, I haven't thought of that yet

[@TechBabu801]

Bro u can use paddle shifters and some button of 4x4 of layout it shows in the game controllers properties

[@zudumalli]

Thanks Bro I got it

[@makhilpranav6949]

what games the MMos wheel config(that u used previously) supports ?

[@zudumalli]

You can play many games. I have played Assetto Corsa, Forza Horizon, ETS2, F1 2020, CarX

[@makhilpranav6949]

thanks for ur reply :)

[@aaditmartin2318]

Bro how did you connect the powersupply

[@zudumalli]

What did you mean?

[@aaditmartin2318]

@@zudumallii meant how did you connect power supply to current and to the motor driver

[@coolproduct5848]

My steering is continuously spinning please help me!

[@zudumalli]

Check FFB direction

[@coolproduct5848]

@zudumalli Everything is working fine but as soon as it reaches 450 degrees, the motor starts rotating continuously.

[@ДімкаІсаєв]

Hello. What engine is it now? Doesn't burn out?

[@zudumalli]

775 motor. it didn't happen.

[@scuffedmanmakesmusic]

i dont see the option for adding buttons

[@zudumalli]

you can use three buttons in this for paddle shifter or sequential shifter. check the description diagram link.

[@manivijeee4130]

Ps5 working a?

[@DriftFusionTN]

what is z toggle for

[@zudumalli]

It is used for wheel calibration, but now it is unnecessary for the new EMC version.

[@DriftFusionTN]

@@zudumalli alright but there is also calibration for the yk

[@DriftFusionTN]

@@zudumalli also not the new version the lite version so i still need it?

[@crashtestdummy82]

how to use buttons with this?

[@zudumalli]

you can use three buttons in this for paddle shifter or sequential shifter. check the description diagram link.

[@crashtestdummy82]

@@zudumalli where is the option to add them in the utility software?

[@zudumalli]

There is no option for that. just connect the button wires to the Arduino.

[@crashtestdummy82]

@@zudumalli and how does the button get registered in game?

[@AbdülkerimYilmayan]

Your Voice Changed😅

[@zudumalli]

I changed my assistant😁

[@rickyabdurohman1330]

Saya sudah lama menggunakan EMC lite, tidak pernah ada kendala, mungkin karna punya saya non ffb 😂 Tapi ada beberapa kemungkinan anda mengalami masalah seperti itu, belt longgar, pulley tidak mencengkram dengan baik pada as roda kemudi, kualitas encoder buruk. Agar lebih awet dan tenaganya kuat anda bisa menggunakan motor dinamo sekuter listrik misalnya my6812, dan ganti as roda yang lebih besar agar lebih baik menahan putaran dan pulley tidak bergeser. Itulah info yang saya dapat dari komunitas😅 Saya tunggu update selanjutnya 👏🏽💪🏻

[@tomassmusicgang]

very usefull info

[@alfawings1958]

Maaf saya instal EMC lite di paling bawah tulisannya firmware ver : unknown. Dan gak bisa di apa apakan .kenapa ya

[@DadanS-g9p]

​@@alfawings1958coba reUpload frimwarenya bang, atau check perkabelan biasanya masalah disitu

[@s4mimawon]

Punya saya FFB menggunakan Encoder 600 PPR, stir di putar 90° error (muter kenceng tidak bisa dikendalikan) sudah di utak Atik belum ketemu solusinya.

[@s4mimawon]

​@@alfawings1958framware Emc nya belum di load ke Arduino.

[@asanuosolo5067]

How many rs is donated for the link

[@zudumalli]

Minimum 10 dollars

[@rexycontemplates]

Where is the wiring to the encoder? 4.7K encoder or the 1K one is enough?

[@zudumalli]

I use a 1k resistor and it wasn't a problem

[@rexycontemplates]

@@zudumalli Alright thanks!

[@athermulla4491]

mine starts spinning continuously after it hit -450 or 450 degreed *cries*

[@zudumalli]

change your ffb direction

[@kavindushehan4380]

@@zudumalli how to change it....