The TRD gauges look AWESOME 👍👍 and the new climate controls should be really nice
@tinle875711 ай бұрын
The crucial part of the removing the gauge needles is not to break the metal needles down below and if you happen to break them you dont have to buy the entire oem gauge cluster. Instead, you just go to a junkyard and get ones from the old GS300 cluster. Haven’t seen anyone except me doing that on my Supra. Problem solved :))
@PureFunction10 ай бұрын
Great information man!
@DutchmanSeb11 ай бұрын
Mike Seegers makes great quality gauges and the HVAc unit will be awesome too!
@fromragstowrenches11 ай бұрын
I may have two pieces of input I'll give a go myself. 1-Speedo. If you've got a lift or jackstands (That you trust) put it in the air and hold it where you need it? No road conditions to worry about. 2. Needle tape application. Do you think cutting strips slightly oversize, laying them adhesive exposed face up, pressing the needles down on them and cutting with a brand new exacto knife would work?
@theslowpra545711 ай бұрын
My gauges look like garbage. I’m going to order these. Are those the facelift TRD ones? I’m trying to decide between the two
@turbogears90011 ай бұрын
Nice look.miss these video's
@ej443911 ай бұрын
No series 2 :( bummer looks like a nice kit
@BuiltToPerfectionLLC11 ай бұрын
Great video bud
@G9RGE10 ай бұрын
Another good video Ryan 👍. What steering wheel is it you have fitted? It looks nice and chunky
@lancetitus981611 ай бұрын
New drinking game idea... take a shot everytime Ryan says "cognitive"
@PureFunction11 ай бұрын
Yes 😂
@PureFunction11 ай бұрын
When I was editing this I even said “why the hell did I say cognitive over and over”
@EvoIXGSR11 ай бұрын
Bought my supra with the TRD gauges 😅
@BadBoyK_1_M6 ай бұрын
Do you know the diameter of the 3 holes for the gauges in the dash cluster?
@shahrozalijafri881611 ай бұрын
What happens when you push the needles in at 0 rpms? With ignition on
@-JX-11 ай бұрын
Your needles will show wrong value, the spring preload is not correct.
@PureFunction11 ай бұрын
What the gentlemen above said, it will not have the correct spring preload and read incorrectly.
@shahrozalijafri881611 ай бұрын
How much would it be off by? Like 100-200 rpms or a lot? And also can’t you just rev the car at like 2000-3000 rpms at a standstill and then push the rpm needle in? And last question 😅 do all cars have to go through the same process?
@PureFunction11 ай бұрын
@@shahrozalijafri8816 just let the car idle, that’s easiest way. Also, it will be wayyyyy off if not done as stated in the video
@shahrozalijafri881611 ай бұрын
@@PureFunction do all cars require the same process?
@justinm25219 ай бұрын
I need a trd rhd temp and fuel in australia to go with my 320km and 10k tachometer, someone help me out?
@relentlessmotorsportstx39711 ай бұрын
Now you see why I charge what I charge to do this style of work.
@Classified711 ай бұрын
good kit but not great i advice u to get a kit from this company (CBS Racing Shop) they have all the tools u need with all the calibration tools also the face they use is like factory not like plasticy looking