DIY Truck Camper Build - Part 3 (Aluminum, Windows, Access Doors)

  Рет қаралды 319,399

homesteadonomics

homesteadonomics

Күн бұрын

Пікірлер: 383
@HAXMAN
@HAXMAN 7 ай бұрын
This whole series has been fantastic. I’ve been thinking about building a camper for years. This is very inspiring. Awesome job brother! 👊
@gregmize01
@gregmize01 7 ай бұрын
you need to worry about sasquatch, plenty on your plate!
@HAXMAN
@HAXMAN 7 ай бұрын
@@gregmize01 😄
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much😊🙏. I’d love to see what you come up with too. If you get one going I’ll be excited to check it out as well!
@jwiereng
@jwiereng 7 ай бұрын
6:32 Seems like the VHB system is dependent on having a well bonded paint. Seems like you're essentially sticking the panels to the paint.
@ThoneJones
@ThoneJones 7 ай бұрын
That’s a really good point.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Yes that is a good point. The paint I used for this is Seymour MRO enamel which is a very good quality of paint. It forms a lifetime bond on surfaces well prepared with primer. But ultimately it’s all a matter of surface area. And like anything it’s, about weight to surface ratio. So if you factor in the amount of weight being held by each square inch of tape, it’s very small ratio. And if you consider that just two 5” strips of this tape would easily hold my 235lbs doing pull ups. And that I’ve got probably a couple hundred yards on this to hold the aluminum on…. It’s not going anywhere🤪 But again, it’s a very good consideration. And if you painted non primed metal that was still wasn’t properly degreased, you might have a lot of stuff falling apart rather soon. But even if that did start ti happen. I could still go back and add rivets or sheet metal screws to secure the panels in the future.
@artsteadman2230
@artsteadman2230 7 ай бұрын
@jwiereng typically commercially bonded vehicle/trailer/camper panels are powder coated - not painted per se. Powder coating is a process that incorporates a positive & negative charge - one for the powder; the other for the surface it's being applied to. Once coated it's subjected to oven curing at 325-350F for 35-40 minutes. The powder virtually becomes one with the metal. As for homebuilt campers etc - a process recommended by 3M but not employed in this vid - it's imperative that the metal surface be wiped down with iso alcohol & allowed to disappate before applying the tape is applied AND pressure applied to the tape to ensure a proper bond
@stevewilliams6354
@stevewilliams6354 6 ай бұрын
I have been a sheet metal worker all my life but let me say this man is very talented Also have never seen a bending brake like that I am very impressed Nice job
@arda1kalas130
@arda1kalas130 7 ай бұрын
Being wise means that do the best whatever you do. So, I can state that this man is a very wise man.
@JonathanBaileyn2u
@JonathanBaileyn2u 7 ай бұрын
Sir.. you definitely have a gift. I hope you see this too. Well done.
@MannyFontes1968
@MannyFontes1968 7 ай бұрын
Joe, you never disappoint with your builds and everything you touch turns into gold...👍
@the_katman2181
@the_katman2181 7 ай бұрын
I love this build. So neat, and you make it look so simple and logical. Which I'm sure isn't always the case as you're doing it.
@kelvinmctavish6369
@kelvinmctavish6369 7 ай бұрын
Very well done thank you for inspiring all of us to save money instead of buying the ridiculous priced campers from the camper rv centers.
@NDA_Fab
@NDA_Fab 7 ай бұрын
Bad Ass Brother! Your getting there! I don't do outgoing SM, but appreciate peoples efforts who do. Great channel, and it goes without saying that you do meticulous work my man!! I am building something very similar and not far behind in progress! I have a full stand up camper with a queen over cab bed all framed up out of 1x1 and 2x1 16ga tubing. Framing in the windows and other misc support today. I'm putting a hatch in the back wall of camper as a modular hole that I can pop a mini 500sqft AC in, stove pipe pass through insert, or just blank hatch cover. Bring what the weather calls for! Otherwise, yeah going with thin aluminum tread below the bed line, and thinking that I am going to go with ACM panels above, all VHB taped.. still deciding on the roof, as I have a hatch and would like it to be walkable in the rear. I love the fact that you're fleshing out the process here. I was thinking of masking the VHB locations and painting the rest of the frame (it will be stored in a garage bay), but the abrasion/primer thing has my curiosity piqued! A number of things really! I hope that your channel is as fruitful to you as it is the viewers, lots of good quality examples of gitten-er-done here! I like your logo too. Reminds me of a friend of mine's thoughts on sports/tv viewership.. "there are enough spectators in the world". Good work, keep it up!
@bdubz5150
@bdubz5150 6 ай бұрын
Excellent build! You installed your compartment doors similar to how we do it in the aerospace industry. Very clean structure, and exterior sheathing joints, etc. I built several campers up here in Mesa, Az. In the past I think we’ve even communicated, and you gave me great directions to a sweet camp spot (Thanks again) My wife and I ended up selling our house in Mesa/Gilbert Az, and buying a big fifth wheel rig and traveling the country the last two years. She worked at a large Metro area hospital in the Phoenix area during Covid and she was ready to leave post “Covid carnival ride”. I sold my last scratch built camper to a nice guy in Scottsdale, and I installed 1000 watts of renogy solar panels on my current fifth wheel with a 800Ah lithium battery bank via a 100amp charge controller through a 10k watt sine wave converter. It can run our 15000 btu dual head split unit Ac/heat pump easily, simultaneously running a large 55” TV and all the lights. I feel like I should’ve built a scratch built Super C RV instead of buying one, as the modern fifth wheels are made in a less than ideal way. We have been settled in Southern Florida for a while bouncing around the Keys, Naples and the Treasure Island area. I miss fabricating my own stuff and my shop I had in Arizona, etc, but we now have plans to build a homestead In Florida, and will utilize a few of your tips from past vids. We also want to build self reliant home on our 5 acres near Gold Canyon Az. To bounce back and forth to as we get closer to actual retirement age. The wife and I love your YT content, and I relate very well to your projects. Keep up the great work, and we hope to be seeing more of your great vids in the future.
@biologistjim4905
@biologistjim4905 7 ай бұрын
To the Rembrandt of DYI……..another outstanding work‼️
@homesteadonomics
@homesteadonomics 7 ай бұрын
Wow! I don’t know if I’m that level….but I’ll take it nonetheless😂🙏
@MrGeroth
@MrGeroth 7 ай бұрын
You are an exceptional craftsman with metal.
@williamolliges2622
@williamolliges2622 6 ай бұрын
That trick with the painters tape and silicone for the access doors was pure genius.
@santacruzman
@santacruzman 6 ай бұрын
Yes. I can imagine Einstein scratching his head trying to solve the messy caulk issue.
@JackBean-rd4uo
@JackBean-rd4uo 7 ай бұрын
This looks like a true underweight camper for my shortbed single cab 4x4 Express Ram. What a nicejob. I love DIY projects.
@garystephens498
@garystephens498 7 ай бұрын
i have to agree with all the others. No matter what project you do, you do it well. You have mad skills and seem to be knowledgeable about so many different areas: plumbing, electrical, metal work, etc..... Thanks for the journey.
@homesteadonomics
@homesteadonomics 7 ай бұрын
I appreciate that…. But I’m still learning and these projects are just the way that I do that. With each one I learn a bit more…. And often times I learn what not to do as well 🤪. Thanks for watching 😊🙏
@RoyDees-t2k
@RoyDees-t2k 7 ай бұрын
Your attention to detail is fantastic!
@TheGentilcores
@TheGentilcores 7 ай бұрын
So many little nuggets… like the trimming of the Blue tape before putting the access panel door on. Made for a very clean install. Consistentl high quality workmanship!
@rickcassell9613
@rickcassell9613 7 ай бұрын
What a great looking camper , it’s coming out great . You could always take on custom orders with your talent Joe ! Quality to detail 👍👍, Well done
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you kindly Rick! But I don’t think my wife would want me to take any orders as this thing has taken me a lot longer to get to this point than I originally thought🤪
@davidbundesen5867
@davidbundesen5867 6 ай бұрын
I have been watching a bunch of KZbin videos on campers and van conversions. It’s really refreshing to see somebody that actually knows what he’s doing and how to use tools. I especially enjoyed seeing you use a router with a flush trim bit for your openings; some thing I did for years when I was a carpenter building homes. Anyway, kudos to you. This is an extremely clean build. Well done sir
@stevektx
@stevektx 5 ай бұрын
I'm so impressed by this project I'm inspired to do my own. Then I woke up and came back to reality that I DO NOT have the skills nor the know how. You are a blessed and talented human being my friend! Please keep the videos coming - whatever you're doing! :)
@cedarfallsfarm9833
@cedarfallsfarm9833 7 ай бұрын
Love seeing the progress on this project, Joe. When I was a kid, I was absolutely amazed by the adults that could do so much, obviously I still am. I think it inspired me to be more self sufficient. Good luck with the 1st outing with the cap on the truck. Mark
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you Mark! I always appreciated the same when I was growing up…. Seeing older guys that were knowledgeable about a lot of different things. And like you it’s always made me want to be as capable as I can as well. And each new year we learn a bit more. Thanks for the well wishes on the first trip too. Literally making final details now to make sure she’s gonna be road worthy, if for nothing more than just storage of the little extras.
@andrerogers9961
@andrerogers9961 8 күн бұрын
Eternabond tape is amazing. Get it right the first time because it ain't coming off. You can get it in various lengths and widths. Beautiful space age looking camper.
@rickbrockthedog8017
@rickbrockthedog8017 7 ай бұрын
Your attention to detail and work quality are two of the things that have made this country great. What a super build. Very impressive. How do you plan on mounting it to the truck? My Four Wheel Camper uses a turn buckle system with eyebolts in the truck bed floor. Pretty easy to deal with. And I'm assuming standard truck camper jacks for getting it on/off the truck?
@mtbguides_Rich
@mtbguides_Rich 7 ай бұрын
Cutting and bending all the panels so accurately is so impressive, good job 👍
@OMGWTFLOLSMH
@OMGWTFLOLSMH 7 ай бұрын
It would be nice to have a shop with a sheet metal brake and a welding rig with welding skills.
@tlmelec
@tlmelec 7 ай бұрын
Nice quality build. One think I would suggest is making the front of the overcab rounded like you did on the leading top of your towable camper. Having an angle like that becomes a big wind deflector and will lead to a lot of drag and reduced mpg. I learned that the hard way myself.
@blackberryhideout5793
@blackberryhideout5793 7 ай бұрын
Fine! Fantastic! Fastidious! Fabulous! Functional! Faceted! Fancy!
@jlr3636
@jlr3636 3 ай бұрын
👍 Industrial Metal Supply, that place is the bomb. They got the stuff, friendly, easy to shop, the go to place for metal in San Diego.
@allanpelton684
@allanpelton684 7 ай бұрын
Beautiful work! Dads are always nice to have as helpers/advisors.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you! And yes they are!😊🙏
@2mustange
@2mustange 7 ай бұрын
This has been a fun series. Preventing water from getting into places is definitely a trial and error. Hope everything you did works but if not you will be able to learn from it and make improvements!
@istj777
@istj777 7 ай бұрын
What a great talent with all your skills and common sense...a super-hero for sure.
@cyclewerx1
@cyclewerx1 5 ай бұрын
Thanks!
@ianmoss5600
@ianmoss5600 7 ай бұрын
Pretty sure I saw you the other day on I-10 in Phx around 75th ave. possibly headed home from your up north trip? You had your camper on and pulling your trailer. Looks good!!
@homesteadonomics
@homesteadonomics 7 ай бұрын
Haha….you probably did! We did a long road trip through UT, ID, WY and CO and were on our final leg home. And the funny thing is that we had stopped a little north of Phoenix to pick up a new buckling goat for my daughter. So when you saw us we likely had a goat in the travel trailer 🤪😂
@branchandfoundry560
@branchandfoundry560 6 ай бұрын
Lots of valuable intel presented here, Joe! Thanks again for all you do to teach all of us.
@Shednanigans
@Shednanigans 7 ай бұрын
You do good work! Keep it up 👍 and we appreciate you sharing this with the world 🌍!
@GaryTrent-qi4ch
@GaryTrent-qi4ch 6 ай бұрын
Very impressive thank you for letting us follow your build.
@JB-mf1zc
@JB-mf1zc 7 ай бұрын
That's a big project Joe and you're doing a professional job can't wait till you get done!!! God Bless!!!
@SethDrew
@SethDrew 7 ай бұрын
Strong work as usual Joe. Can't wait to see the completed project. I might still some of these ideas for my planned military trailer slide in.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you so much Seth! Also, I heard about your Dad. I wanted to comment on one of yours or Steff’s posts but just hadn’t had the right words yet. But I know he was a good man and father to some incredible kids(grandkids) that are a testament to his legacy. And I know he is now at peace with his Heavenly Father!
@johnstewart6500
@johnstewart6500 7 ай бұрын
Amazing work Joe.
@santafefavs
@santafefavs 7 ай бұрын
Yes thank you. I did see your comments in the video. But I didn’t understand it then. Now I’ll have to try the grove technique you did. You really solved a very tough maneuver. I didn’t think of it. I ended up with a very distorted piece of angle.
@felixcat9318
@felixcat9318 4 ай бұрын
Your metal store is fantastic, I wish there was something similar I could access easily.
@tomtruesdale6901
@tomtruesdale6901 7 ай бұрын
That camper is turning out great. Can't wait to see the finished camper. You will have a heck of a rig now with the camper on your truck towing the camper trailer.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you! I’m hoping it’ll make a nice companion to the travel trailer but also for off site jobs and solo hunting/fishing trips. A lot more work to do for the roof, door and the interior and electrical. But the bulk of the major stuff is behind me now. 😊🙏
@baltescamilla853
@baltescamilla853 6 ай бұрын
Fantastic job, you make it look easy but I know that it’s not. Precision work/results with basic tools… AMAZING
@davegardner6592
@davegardner6592 7 ай бұрын
The 3 m product tape is great The Cardinal stadium sighting is installed with it. in Glendale Arizona
@ishtarlopez6203
@ishtarlopez6203 7 ай бұрын
Hey howdy y'all, what up peeps! Hope I'm not too late for the after party😅. Big shoutout to the Bend-O-Nomics! Woot woot! 🎉🎉 Well Joe this is super impressive! Idk which I'm more surprised by, this or the greenhouse. You've certainly outdone yourself! Kudos, kudos, kudos, good sir! Woot woot!🎉🎉 P.S. still waiting on that live, cough cough, wink wink ... 😉🤭☺️😁😅
@iwantosavemoney
@iwantosavemoney 7 ай бұрын
I really like this build it once build it for life
@803mastiff9
@803mastiff9 6 ай бұрын
Industrial Metal Supply is an amazing place.
@stuartkorte1642
@stuartkorte1642 7 ай бұрын
This is turning into an awesome project. I was wondering about how the VHT tape was holding up on the trailer and you answered. Thanks. Thanks for the leads on the other items also.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much Stuart! 😊🙏
@jaystewart9947
@jaystewart9947 7 ай бұрын
Looks great Joe. As always, very detailed and great attention to the details. Top notch Sir
@mertonallowicious
@mertonallowicious 7 ай бұрын
I have a roll of grey eternabond waiting for me to start my camper build… nice job you are using a lot of the construction and assembly techniques I’m looking to try, it’s great to see
@homesteadonomics
@homesteadonomics 7 ай бұрын
It’s really good stuff and keeping the water out, is probably the biggest ‘must’ when building any thing. So I’d say you’re off to a good start. Let me know if you have any questions on your build. Not that I’ll have the answers but maybe I can give you an idea of what worked for me😊🙏
@OIII-IOOO
@OIII-IOOO 7 ай бұрын
very slick and futuristic looking. nice job, Joe.
@josephwest7227
@josephwest7227 Ай бұрын
Very interesting, thank you ,I'm in British Columbia, Canada.Thanks Again
@robh2515
@robh2515 7 ай бұрын
Hey Joe... With you being in a desert area, Is that a popcorn machine or pizza oven..Ha. Kidding... we're always impressed with your projects. We installed our aluminum side panels on our cabover with 3M tape today. Your video was a tremendous help. Thanks
@280zone
@280zone 7 ай бұрын
Always appreciate your meticulous attention to detail. Looking forward to why the roof might need to pop open:)
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you! As for the roof, it will need to pop up as the interior is just about 5’ and in 6’. So just for standing room. Of course it doesn’t look as low right now because that dolly gives it about 10” or so of height from ground level.
@antonioc9396
@antonioc9396 7 ай бұрын
the workmanship is superb! super awesome build!
@mandyleeson1
@mandyleeson1 7 ай бұрын
So well thought out. Brilliant build Joe, looking forward to the next update 👏🏼🙏🏼
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much Mandy! 😊🙏
@TurkiAlsubiee
@TurkiAlsubiee 7 ай бұрын
Great work, man. Maybe in the future you will make something like it, consisting of two pieces. Its sizes are flexible. You can adapt it to a truck of known sizes. Also, perhaps the roof can be raised while standing, and its sides are made of durable fabric. Thank you and I wish you success. Your follower is from Riyadh, Saudi Arabia.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you! As for the roof….it will be made to pop up so I can stand in it. But that’ll be in a future video. Also, great to hear from Saudi Arabia! 😊🙏
@TurkiAlsubiee
@TurkiAlsubiee 7 ай бұрын
In my country, Saudi Arabia, there are local institutions that manufacture something like this, but not with your mastery, and they only seek to make money, unfortunately. In addition, we do not have the capabilities available to buy ready-made windows and doors locally, and importing them from abroad costs a fortune. Thank you again.
@bryanlane31
@bryanlane31 7 ай бұрын
Just discovered you today…caught up on the first three videos for the camper, now I’m going to go look at the trailer build. Fantastic videos!
@randallthompson5769
@randallthompson5769 7 ай бұрын
Looks like a nice camper!! Doing a great job!! Thanks
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much Randall!
@cynthiabroaddrick7197
@cynthiabroaddrick7197 7 ай бұрын
It is amazing..you don't have a rivet or two in those panels? That is amazing tape!
@homesteadonomics
@homesteadonomics 7 ай бұрын
Nope. But the trim pieces on the corners and edges have sheet metal screws. So theoretically if all the tape failed then it’d still be held on by those pieces.
@artsteadman2230
@artsteadman2230 7 ай бұрын
@cynthiabroaddrick most all horse trailers, utility trailers, emergency vehicles & RVs have used VHB tapes for decades. Rivits are labor intensive whereas tape isn't. Plus tapes allow torsion movements created by normal travel allows for the units to flex & bend - rivits in the other hand are rigid. As for horse trailers rivits & the space in-between each Rivits allow air passage that creates a thunderous 'waffling' that spooks horses. Meaning you'll get the horse in the trailer just once. Likely not again
@asdasdsadasdasddsff
@asdasdsadasdasddsff 7 ай бұрын
she's a beaut, well done!
@paintingwithextremeaffect7821
@paintingwithextremeaffect7821 3 ай бұрын
I am just so jealous! Now I want to build one!
@lucsurmon2623
@lucsurmon2623 7 ай бұрын
As usual very interesting and amazing work 👍
@espnmk
@espnmk 7 ай бұрын
Quality job! Joe Thanks for Sharing your skills and how to...
@roseapple8786
@roseapple8786 7 ай бұрын
Mr. Joe looks great. You always do a fantastic job on all your projects. Now will this be for a working truck or for camping. Thank you for sharing and God Bless you and your family. 🥰👍👍👍👍👍
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you Rose! It will be mostly as a work shell to do projects off site and hold my tools. But secondarily it’ll be for my solo hunting trips as well. So perhaps 75% as work/utility topper and 25% for camping. And may the Lord bless you and your family as well!😊🙏
@MaryBrownForFreedom
@MaryBrownForFreedom 7 ай бұрын
3M needs to sponsor you LOL that VHB tape is good stuff! I used it to attach an antenna mount to my pickup and the mount is still on there 15 years later... and it is exposed on the edges so water gets at it!
@dustman96
@dustman96 7 ай бұрын
It's too nice, you have to start over! Adhesives are awesome. With proper selection and prep you can have extremely strong and long lasting bonds. Good epoxies have a tensile strength of 8000 psi. You could basically hang a bulldozer off a 1 square foot bond, probably more like 4 bulldozers.
@homesteadonomics
@homesteadonomics 7 ай бұрын
Haha… my wife would kill me if I started over🤪 And yes, the adhesive world is amazing. Crazy the bonds that these new and some of the older products have!
@ratfinder7812
@ratfinder7812 6 ай бұрын
Thank you so much for your fantastic videos, I have definitely learned some new techniques. Just want to throw this out there, since you are very creative, I was wondering have you thought about making a bed slid, so you can utilize the entire bed of the truck for tool storage without having to climb up in to the bed of the truck…. Again, thank you, I have been subscribed for years now.
@stilcrazychris
@stilcrazychris 7 ай бұрын
Nice job Joe.
@jonathanemocling3826
@jonathanemocling3826 7 ай бұрын
Wow Just stumbled on your video. This build is awesome I would hire to do a build on my own camper truck. This is what I’m looking for. I will follow this awesome build. Much Aloha from the Islands
@JohnThomas-gj2zg
@JohnThomas-gj2zg 7 ай бұрын
Looks great so far on the work you have done to it ...
@ksfixitmangaming617
@ksfixitmangaming617 7 ай бұрын
Awesome content as always. You amaze me with every video. I didnt think you could top the travel trailer but was I wrong. Cant wait to see the finished product. Be safe buddy and Ill be looking forward to the next video. 💙
@idahoman325
@idahoman325 6 ай бұрын
Heres hoping he up & decides to add a pop up roof top to further expand the space.
@tobyswesternwear
@tobyswesternwear 6 ай бұрын
those angular sides would be perfect when I get a cybertruck someday.
@Drwwf
@Drwwf 7 ай бұрын
Dang uncle Joe it’s turning out good
@homesteadonomics
@homesteadonomics 7 ай бұрын
Hey Buddy! Thanks for checking it out! And also make sure to pencil some time in to come up when Marley and I are building the goat cart. We will need you to come and help test it out😊👍
@alkuerbis5712
@alkuerbis5712 7 ай бұрын
Interesting handmade break
@cleokey
@cleokey 7 ай бұрын
Well done. I built one out of plywood, to heavy be practical, I like this. 😊
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much!😊🙏
@hide03291981
@hide03291981 7 ай бұрын
wonderful beautiful camping Car
@Handirifle
@Handirifle 7 ай бұрын
VERY impressive workmanship. Nice job. I am curious why no over cab bed?
@lorenmeyer5290
@lorenmeyer5290 7 ай бұрын
WOW very beautiful great job Joe!
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you much Loren! 😊🙏
@walkaboutmotors
@walkaboutmotors Ай бұрын
I’m in part three where you add the outdoor and indoor siding. Is there a reason you didn’t fill the space with expanding foam or another type of insulation? Weight? Love your videos and your engineering for this camper is excellent!!! You’ve helped me think through my build and I really love your design!!!!! Excellent series of videos!!!!
@ThoneJones
@ThoneJones 7 ай бұрын
Awesome. I need to try out that tape on some stuff.
@homesteadonomics
@homesteadonomics 7 ай бұрын
I’ll tell you what….i use it on SO many little projects here and there. I think I’ll always keep a roll handy as it proves useful in so many things. I get mine from SRI supplies…..CV62F and CV45F (thinner for overlaps). It’s expensive but it really dang useful!
@DesertOwlForge
@DesertOwlForge 7 ай бұрын
Looks really nice. Looking forward to the next one. 👍
@Jasonoid
@Jasonoid 7 ай бұрын
Excellent work. Very clean build so far! Great explanations :)
@Micksjourney
@Micksjourney 7 ай бұрын
That looks good. Nice design. Although it is likely there will be galvanic corrosion since you are mixing steel and aluminiumin in direkt contact with each other..
@homesteadonomics
@homesteadonomics 7 ай бұрын
The paint and VHB provide separation between the steel and aluminum. The only area where there is any direct contact of aluminum and bare steel is in the rivets on the in-fill aluminum pieces on the cab-over section. Which is minimal. Maybe 15-20 rivets total. And is also backed up with VHB. More over this is the same exact construction I used for my DIY travel trailer project. Steel framing, aluminum panels, etc. Hope that helps and thanks for watching 😊🙏
@loadedi812
@loadedi812 7 ай бұрын
Very cool build and well put together video. Impressive. Have you considered bonding the inner and outer panels to an insulation board so that you wouldn't have to do so much frame work? Just a question, only because I'm looking at building one myself, and am looking at how to save weight.
@crankshaft007
@crankshaft007 6 ай бұрын
Sweet nice job
@onlyychevys
@onlyychevys 7 ай бұрын
I would love to know what it weighs when done, I might be building something similar in the future. Very nice build so far!
@bajajoaquin
@bajajoaquin 7 ай бұрын
I’ve taught my kids that IMS is the true happiest place on earth
@jasongrinnell1986
@jasongrinnell1986 7 ай бұрын
Have you ever thought about drilling your own water well? I drilled my own well but I did lots of homework on how deep to get good drinking water. Not sure it’s an option for you depending on where you are located. Lots of places in the desert areas contains lots of fresh water. Just curious.
@davestewart9146
@davestewart9146 7 ай бұрын
I really like your design, nicely done sir 👍😁
@shawnbryant60
@shawnbryant60 7 ай бұрын
That was truely an excellent build!
@billoobillaa5900
@billoobillaa5900 7 ай бұрын
Clean job. I wonder how hot will it get under ☀️
@ArtBeHereNow
@ArtBeHereNow 7 ай бұрын
We use VHB tape to install glass on multi story buildings, It gets some backup from the silicone weatherseal between the glazing units but its the tape doing the lions share against windloads. LOL
@homesteadonomics
@homesteadonomics 7 ай бұрын
Yes, absolutely! You know first hand then….. I remember my buddy Jake telling me about that years ago when he was working on some high rises in Phoenix and Dallas and I was like…whaaaat? Tape?. And now I absolutely love using this stuff!
@flittlefield
@flittlefield 7 ай бұрын
Maybe I missed it, but what about insulation. Is that coming later? Thanks for showing us this build.
@homesteadonomics
@homesteadonomics 7 ай бұрын
I’ll address that in a future video. But if you look closely you can see that I already have most of the insulation installed. It’s 1” rigid foam insulation.
@englishpower5007
@englishpower5007 Ай бұрын
Great!! How do you make insulation in the camper? How to secure the camper in the bed?
@danypeguero2512
@danypeguero2512 5 ай бұрын
Very high quality video, learned a few things. Why did you choose to not have the forward top portion match the rear width dimension? I have only watched part 3 incase you answered this on the previous videos.
@Llamadosalvaje
@Llamadosalvaje 7 ай бұрын
Amazing peace of art!
@danyo492
@danyo492 7 ай бұрын
This is incredible. Awesome job!
@homesteadonomics
@homesteadonomics 7 ай бұрын
Thank you very much!
@FredMcIntyre
@FredMcIntyre 7 ай бұрын
Looking good Joe! 😃👍🏼👊🏼
@dangoras9152
@dangoras9152 7 ай бұрын
That's awesome brother its looking slick.. Keep it up brother
DIY Truck Camper Build - Rear Entry Door Pt 4
15:34
homesteadonomics
Рет қаралды 55 М.
5 Things We HATE About Our DIY Camper
9:24
Ambition Strikes
Рет қаралды 521 М.
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
DIY Truck Camper Solar, Lights & More! - Bluetti AC180  ( Part 6 )
19:38
homesteadonomics
Рет қаралды 32 М.
DIY Truck Camper Build  - The Frame Pt1  ( How To )
16:25
homesteadonomics
Рет қаралды 256 М.
DIY Assembly of Composite Panels and Aluminum Angle for a Homebuilt Camper
12:19
Boreas Composite Panels
Рет қаралды 60 М.
Can You REALLY Build Your Dream Bus Home in Just 6 Months?
48:52
Renovation Process
Рет қаралды 881 М.
ULTRA Light Weight - HIGHLY Insulated - RUGGED Off-Grid Truck Campers
12:55
New Jersey Outdoor Adventures
Рет қаралды 485 М.
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН