DIY Very Powerful Subwoofer with PVC pipe / powerful bass

[@lawan1603]

Biggest success of this project is the near 10millions view.

[@sevenohm3375]

you can buy a lot of speakers with that many views.

[@JoseLuisUrzagaste]

😂😂😂 nos engañó a todos

[@joefish6091]

Its educational for people to watch and learn construction techniques. Sometimes the biggest hurdle is the first attempt, people fear to make mistakes. If somebody is making a loudspeaker for the first time and they don't work 100% , rip em apart and tinker with the design. The finale cosmetic covering will hide the attempts and versions...

[@frankymino8773]

I believe you would need a crossover for the speaker to only drive the lower frequencies for it to actually be a dedicated subwoofer. Even then you still need a woofer (speaker) that is rated down to 20hz or at least down to 50hz for it to be classed as a subwoofer.

[@hoseaembury1999]

This video is a great example on how McDonald’s sells the most hamburgers of any hamburger joint, but they’re the worst hamburgers.

[@etmesi]

I guess the theory is the PVC Tubes funnel the Bass, but the length distance the air travels causes a delay better Bass. In the 80's instead of baffles or tubes, I used two or four woofers in a car in 1982. Never made a box square but they had a few angles if not rounded backs so the bass does not just bounce against a flat area never sounded as good. Woofers that required a large box to perform correctly, I reverse the polarity some how worked great.

[@giggling_boatswain]

I wonder what the theory is? Why do you need such a long duct? After all, we all know how the tube distorts any sound. If the emphasis is on amplifying low frequencies due to resonance in the pipe, then I would like to see a method for calculating the diameter of the pipe, its length and the number of elbows, which are highly undesirable in acoustics. Otherwise, there will be no amplification compared to a conventional phase inverter, but we will only get a distorted, colored sound that is very far from the sound engineer's idea.

[@kssps2009]

Yes. I do agree with you. But, you should also appreciate his creative idea.

[@OronOfMontreal]

Similarly, I was wondering if you calculated the overall length of the ducts, to make sure that their output is perfectly in phase with the output of the woofer.

[@PraveenPLCE]

Arinjudenki mindathirunnu kaanu

[@jonfranklin9361]

I think after a certain amount of tube the gains are diminished. We use to build subwoofer boxes,use different diameter and length of pipe to tune the boxes.

[@Michaelkaydee]

The size of box determined how many elbows he needed for the length of duct he wanted to produce his desired resonance...

[@GratefulFloyd]

I take it, there's no crossover, so it's a full range speaker. Very nice construction. Very soothing to watch

[@alexanderangelkov6338]

Thats a woofer not a midrange

[@hbeezey]

obviously, it's not even a subwoofer

[@indrazeine6817]

Didn't hear the subwoofer sound.

[@smoker420la]

That's the point

[@NickkaDUB]

What is that? 6”?

[@mridulkrishansharma5394]

​@@NickkaDUBthat's what she said

[@itssammiesakran]

​@@mridulkrishansharma5394😂😂

[@NickkaDUB]

@@mridulkrishansharma5394 For me it’s more like she says, “What is that, 6” soft”?

[@tomstrum6259]

Don't Knock it too Quickly.....This is an Improved (Larger Speaker) version of the very popular & Successful Bose tuned "Sound Waveguide" tabletop Stereo radio design.....When properly Tuned, most casual Non-Audiophile listeners are Impressed & Prefer the amazing Improved Bass sounding performance of this Relatively small size stereo radio !!

[@ckmoore101]

Its called Boom/sizzle. As everyone in the industry knows, Bose is a marketing company, not an audio company.

[@континентпрайм]

Прекрасный , пластиковый звук😁😁

[@СимонБоливар-м5х]

они тупые. как говорил Задорнов.

[@treyrhodes]

A few things come to mind. 1. The Xmax of that speaker is likely not sufficient to handle the wavelength desired by such a port. 2. There will be all sorts of unusual resonant frequencies heard with this un-reinforced construction method: tubes, ports, cabinet. 3. The enclosure and the desired port tuning frequency do not appear to be well matched. 4. The port length and diameter do not appear to be well matched. 4. There are bound to be phase issues, here.

[@petyaur]

My first intuitions were something similar. If you want a TL, you'll build that. :)

[@351clevelandmodifiedmotor4]

for best results the port should be in the face of the box and a certain length and width,

[@351clevelandmodifiedmotor4]

this person has good craftmanship and designs but doesnt have a clue how speakers and subwoofers work,

[@sevenohm3375]

how do they appear unmatched? doubt he just winged it for the sake of views.

[@keithanthony9996]

Wow you must be an expert,,, Not!!!

[@kilogram064]

I remember putting my cassette player (I know, I'm old) into an empty dresser and opening the drawers. this was in 1970 something and the sound was amazing.

[@viethoanghoang6231]

toi ngi la lam de cho vui thoi chu thuc te la lam ong hoi bang ong nhua nhu vay theo toi ngi la khong hay.day la y kien chu qoan cua toi thoi

[@TheGoori]

I tried that as well and it did make a difference.

[@chuckmaddison2924]

I still have a cassette deck. But your idea of the doors is not new. I have a Kriesler stereogram from 1968 with sliding doors at ends over the speakers. So it looks just like a nice cabinet when not in use.

[@edhorlickbullecer8564]

I still have my cassette tapes and players in my house. Surprisingly, they still play. 😅😅😅

[@catmanisgod8200]

You are not old.... I had an 8 track in my first car. 😉 I still use an 8 track in my workshop. I have an old stereo from early 70s that way I don't have to worry about theft or damage. Many years ago my father would pick up 8 track tapes for me at yard sales for ~$0.10.

[@Teknakill]

I doubt it really makes it sound better with all that piping, plus if you are going to use piping, have a clear window to show it off with 12 volt led lights connected to the speaker too and make it a show. Kind of like a gamer pc with a clear window, all that bling bling showing off to be a cool guy.

[@ЮрийМанжола-щ6п]

Прикольно получилось..... теперь можно взять резиновые тапки и сыграть на этих трубах что то из Blue Man Group!)))))))))

[@robertfripp62]

I feel love!!!!!

[@Enigmaticpower]

Посвящается фетишистам лампового звука😀

[@АнтонШматов-ш4с]

Такой системы из каланизационных труб я еще не видел :)

[@ДенисКачко-ж8о]

Потому что смысла нет, только для таких видео... Задержка из-за большой длины трубы будет и возможно сопение

[@adambisultanov76]

@@ДенисКачко-ж8о да и ящик тоже великоват. Для такого динамика хватило бы и сливного бачка (как раз в тему видео было бы)

[@АнтонШматов-ш4с]

@@adambisultanov76 думаю унитаз будет хорошим объемом для динамика, а выпуск унитаза фазоинвертор

[@chrisa9035]

​@@ДенисКачко-ж8оthings probaly tumed to -20hz😂

[@moseskariuki1896]

A skilled plumber

[@glennmorgan4197]

Have you never heard of pvc glue? Hot melt in not going to stand up to the vibration of a subwoofer. As far as shaping the porting of the speaker, it could have been achieved with wood panels that would have strengthened the cabinet and taken less time. And where is your baffling to stop those large panels from resonating? Sorry dude, but you have a lot to learn about speaker design.

[@Anmobgoccult20]

BBBravoooo, bravo you are a big master, very pleazure for me to see this, tnx. and ful respectfull from old BG.

[@ankurchauhan1151]

the vent should be on the front... the box is huge you can put the mid and high range as well, insides of the box should have the sound absorber too you can use carpet or foam material. The effort is brilliant....

[@bobverney4903]

It makes no difference, bass is not directional.

[@DRXxUziixX95]

​@bobverney4903 it does make a difference for group delay and when you put the speaker against a wall to use room gain.

[@HumansAreShitFactories]

Make your own vid

[@lanatol57]

Чугунные трубы сделали бы звук гораздо винтажнее!!! Верьте мне! Дарю идею!

[@КонстантинКитов-н3й]

чугунная секционная батарея !!!

[@Alex-yr4qi]

А если мощный динамик вставить в унитаз, вообще сабвуфер получится😂

[@АлександрСлайерков]

​@@Alex-yr4qi чтобы звук стал воистину аудиокакафильский, нужно к унитазу огромный рупор как у патефона присобачить, а в унитаз впиндюрить ширик 150 ГДШ. Вот тогда вообще сказка а не звук будет 😝😂😂😂👍

[@МихаилПронге]

Всё это замечательно! Но вместо лабиринта нужно подключить канализационную систему всего дома!

[@kataeff]

На ютубе уже есть видео, как парень ставит динамик вместо канализационного люка 😂

[@ശബ്ദ.കണ്സൾട്ടന്റ്]

remove the fittings pipes, &all then give 4 inch one pipe length 20 cm locate just bottom of near same woofer ( not back I mean front ), put glass wool inside box all sorround so you Will get more deep smooth bass 🙏

[@fiqueporaqui]

Did you mean, to use only ONE 4" pipe, 20cm long and on the front, lower part of the box? Does it matter the size of the box, as dimensions of this project were not given?

[@edhorlickbullecer8564]

I agree. I did the same thing with my Kicker ES 12" . It really produced a deep soothing bass.

[@eustahijelifetips]

​@@fiqueporaqui4" port on a 4" speaker lmao

[@romero71chris54]

Very creative interesting concept worth it I doubt it.

[@JR-nh4kb]

У чела остались обрезки труб после ремонта сантехники и он решил забубенить ролик для впечатлительных. Результат достигнут, суб собран. ХайФая никто не обещал. В мире стимпанка идея прижилась бы 😎

[@lanatol57]

А фанэру - подобрал на свалке

[@JR-nh4kb]

Скинул я этот ролик спецу и однако ... : Я: -"Прокоментируй пожалуйста эту контрукцию. Ты в этом разбераешься." Он: -"Это туннельный фазоинвертор, самый высший класс акустического ящика..." Я: -"Эта конструкция может выдавать красивые басы?" Он: -"Ну типа самые глубокие".

[@keramzitJo]

@@JR-nh4kb ну то есть эта фанерная штука типа крутой фазоинвертор ?

[@JR-nh4kb]

@@keramzitJo Это мне сказал человек, который сам ещё ~25 лет назад собирал подобное на заказ.

[@trading24h199]

Thank you very much!

[@kingmakespeaker1402]

Thank you for donating $

[@AFRIKDIOULASSO]

m.kzbin.info/www/bejne/aImkmqinp62egZI

[@ibnumuzki5310]

ĺk0popo

[@robertcperry4377]

Hey. Well worth the trouble. Sounds great

[@robertcperry4377]

Sounds great

[@trunglequang6310]

Nhìn thấy co ống Bình Minh là biết bạn người Việt Nam. Tôi là một người thợ điện tử đã nhiều năm (60 t) nhận xét: bạn có sáng tạo, nhưng loa sẽ nghe không hay đâu vì lượng không khí bên trong loa số với ống hơi không được cân. Lưu ý là ống hơi nếu dài phải đi tù nhỏ ra lớn như saxo và phải có thể cắt ngắn hay thêm độ dài. Chúc bạn vui.

[@HoangNguyen-dk3tu]

Làm cái ống hơi cho đã đi r cuối cùng cái loa nghe còn thua cái loa ống hơi bth nửa😂

[@Oleg_Mexavoi]

Сантехник в деле.

[@JSAFIXIT]

If you use a compression bit vs just up or down spiral fluted bits, you can get much cleaner cuts, in less time.

[@gum83821]

PVCを使えば、より簡単につくれそうですね！

[@asdermayer]

I am missing the insulaton troughout the box, under the rim of the speaker, the connector, around the pipe exhoust. Everywhere where it can wistle/blow. Otherwise this is a great build with much details around the woodwork :) (I also would use a bit thicker cable, i am not sure about the power of this speaker, but it doesnt cost much) I also built speakers without any calculations when I was young, but propably its worth it. Anyway the satisfaction of listening to a speaker which you built on your own makes it the best in the world :)

[@greggmitchell615]

Nothing better than to hear your own design of a speaker actually work and sound sweet.. I make car sub enclosures . Good work

[@tangomantactical]

Without using T/S parameters everything is a guessing game. Thats why the specs are there. Gotta love the wood working CNC machine.

[@tangomantactical]

Also a transmission enclosure will work the same way, and no tube have to be purchased and rigorously worked.

[@kman808alohamovement3]

Specs and dimensions? For different sizes speakers say like 10 or 12 inches? Ty for the video. I’d probably use different adhesives in my opinion. What about the vibration after time? The PVC will generate rattling sounds correct? if the PVC isn’t properly secured or braced? Sorry for all the questions just curious on the science of it all. Very interesting. Thank you again.

[@danielchadwick8513]

Now attach the speaker to the pipe to protect the speaker fully and fill the box around the pipe with cement/concrete/epoxy resin slowly to prevent any air bubbles and to make the pipe as RIGID as possible so that it prevents vibrations that causes the pipe to rattle over a period of time

[@ВикторХарченко-з4н]

И главное - никакой музыки🤣

[@tonywa9343]

And then buy a engine hoist, so you move it about the room

[@danielchadwick8513]

@@tonywa9343 Once placed in the right place they don't require to be moved a simple wheel board would help to find out the right place The point is purity of sound clarity not your sarcastic remarks which you are accountable for because that is your responsibility

[@Wised1000]

Pulled the words right out of my mouth. Hoewever, simple sand will do. Finally, just using a long tube "waveforming" is not enough. The tube has to be tuned, if not, you get lower but smeared bass. Also, the ports need to be tapered, if not, it will also "chuff". Its easier to simply make a bass reflex enclosure, the bigger the box, the lower the bass. You can also add a passive radiator for additional extension.

[@nagomizik9358]

@@tonywa9343 😂😂

[@mamaassam3044]

Thanks for sharing 👍+🔔✔️new friend🙏

[@vicboa]

Gran trabajo! sólo hubiera preferido que las salidas de aire sean hacia el frente, para que no rebote el aire expulsado si se coloca el equipo cerca de una pared quedando limitados. Felicitaciones!

[@garyandrews746]

My one has turned out exceptional with room filled bass output and audio excursion happening at the speaker level. I have used WIN ISD for the design and acoustics of the box. Then a friend helped me with the MDF sections. I have mine in a 4th Order MDF bandpass with the sub down firing. As this is in a sitting room getting the correct amplifier was a problem in NZ do not order these from Aliexpress. Once I sorted the amp and connected wiring the beast fires up. The sub and enclosure and audio electronics is set to only resonate at the sub level 40hz to 120 hz and the port tuned to 44hz. LFE is the bass track in 5.1 and what is fed into this (Low freq). A 12 inch JVC DRVN is optimal for this type of job if paired to the correct amplifier my former bass speaker was a old sony stereo speaker that was not designed for the LFE and the new setup is truly a bass driver now (the .1 in 5,1). I have to tweak the audio settings to acheive even better quallity. For the price the JVC 12 inch DRVN does well.

[@marcos_pefe2936]

PARABENS !! eu aqui consegui sentir a QUALIDADE dos GRAVES .. muito bom imagina ai perto da Genial caixa de SOM .. PARABENS !!

[@qddk9545]

I have always liked tube equipment 🙂

[@Vasilij_Terkin]

I would call it a rattling wave damper. Look at the device of the pipe of the old gramophone. 📯 Gradual diameter transition and proper swirl to gently remove other noises. The volume of the box must be in proportion to the room so as not to create resonance. And some polyurethane foam inside

[@pangeran1928]

That Good Kreasi...I Like your kreativitas 👍 Dadi Arep Pesan seng koyok Mini Compo Ono layar sentuh e👍👍👍

[@Scharbach77]

You are all missing the point here, ignorants! This dude deserves credits and respect, for the soul reason alone; He is a maker, a builder! He create on his own terms and skill level, that makes sense to him. This way he achieves valuable experience and knowledge about making a speaker. In the end he will know what really works in practice, in real life and not what most of you guys, think you know about theory from reading a book!

[@aarong8457]

You're the OP with an alternative account.

[@atulbisht2989]

bro fix the table 😃, nice project!

[@koonjulougrasen4432]

As the loudspeaker is a full range one, I would have used a low and high frequency crossover in parallel to the speaker .

[@NoelFranciscoDeslate]

Wow! it sounded like Blue Man Group Drumbone!

[@thedayafteer]

Not to despise your work, I own a marshall stanmore Bluetooth feels like a high-end facility 👍

[@danielpessoa7160]

Olá. O profissional em epígrafe deveria trabalhar com COMPENSADO, no lugar desse papelão, chamado MDF. A acústica ficaria muito mais substancial.

[@ESBATUPapua]

So nice... 🇨🇺🌹

[@joeysarmiento1925]

Happy 2023. Good luck to us all. I did this using a 3" PVC pipe with the same 3 u-joints and 2 L-joints and I am pleased with the outcome using an 8 inch mid-bass.

[@ВячеславЖурлов-б1й]

Необычный фазоинвертор. Несколько странно, что он имеет выход в тыл. Фронтально, было бы много выигрышнее, думаю.

[@Bassotronics]

I use this same type of tube system for my car. But the chamber where the speaker goes is also tube. The guy here still used a box though. It’s my favorite and best for anything below 25Hz! My tube complete tube system is about 25lb compared to a conventional bulky square box that needs bracing would be 80lbs which for a daily vehicle sucks. Ever since I discovered tube systems, it’s all I use for Bass systems!

[@zip.gianni4045]

It's bullshit ....

[@zip.gianni4045]

Systems has valves are stoves I use integrated amplifiers stable on two hom By car

[@Bassotronics]

@@zip.gianni4045 You are ignorant.

[@Toter]

Where can I learn about this? There has to be more people doing that.

[@Toter]

@@zip.gianni4045 what?

[@paniot8414]

Well, nice box. As for the sound quality it's exactly as it should sound out of a sewage pipe.

[@МихаилЧеренков-г6г]

А ЕСЛИ ТУДА ЗАСУНУТЬ УНИТАЗ , ЖЕЛАТЕЛЬНО ПОСЛЕ 25 ЛЕТ ИСПОЛЬЗОВАНИЯ В ОБЩЕСТВЕННОМ ТУАЛЕТЕ, ЗВУК БУДЕТ ПРОСТО ШИКАРНЫЙ. НУ ПРОСТО КОСМОС.

[@ZiminRZ]

Они так и делают. Только нам не показывают, думают что мы им завидовать будем.

[@mich0000]

​@@ZiminRZ кто такие "они" и кто такие "мы"?

[@urbantechrobotics4379]

Jajajajaja... You're absolutely right ! ...

[@chesterdonelly9893]

Так вот почему каловая масса из рф в Украине в первую очередь унитазы срывает и домой везет. Акустику создавать стало быть. Прав был Герман Греф, ох прав

[@uniqko]

You are so amazing

[@ak74mtco]

Интересно сделано, но из за такой длины труб фазоинвертора и большого количества изгибов вместо хорошего баса получится искажённое бубнение. Лучше бы вы сделали тот же короб со щелевым фазоинвертором или четвертьволновым резонатором, в крайнем случае с трубой Войта

[@user-dv9cb7tm8o]

Думал, что посмотрю ролик про аудиофила. А посмотрел ролик про плотника.

[@АлександрФадеев-ю5т]

Из всего ролика мне понравилось как он аккуратно собрал корпус )))

[@user-dv9cb7tm8o]

@@АлександрФадеев-ю5т Вот-вот )

[@vladdymin]

+ сантехника

[@NackDSP]

It is far less expensive to simply buy two drivers, put them in an appropriately sized sealed box and equalize the bass response. You get a bass response that rolls off less than this design does below the port resonance and you get accurate bass with low group delay that a ported design can never have. Modern accurate hifi speaker designs don't use ports, open transmission lines or passive radiators.

[@jeffjapisinchannel9507]

Good job bro..👍👍

[@cduncan3713]

I had a set of tuned speakers. they use an o-scope , generate a tone , adjust the tube length until the tone is just right.

[@sharoondaniel8889]

Amazing speaker 🔊🔊🔊

[@Padde298]

If you cut the MDF on a cnc machine, why do all the sanding and grinding? Why the last bend on the port? It only directs the opening chose to the front... Why not place the port openings on the front and not the back? Why make two ports and not just one? Did you do ANY calculations to the port and the length? I have NO suggesting as to what you should make next, but I would suggest anything else than a speaker enclosure!😝

[@enzofiero2924]

I've seen this guy do some things that leave me scratching my head, always.. But it's a good way to kill time 🤣

[@Padde298]

Waste time you mean..?

[@venom-kc7ri]

he is legend in his own way🤣

[@wernerlampe8089]

Die komplette Konstruktion ist absoluter Schwachsinn! … 👎

[@PhatkatCollections]

This is nothing more than a super low tuned ported enclosure. The pipes are sinking because he opted to use two , what appears to be 3 inch ports, the smaller the volume the longer the ports have to be. Add a second, and the ports need to be even longer. This looks cool but is not really necessary.

[@westkolx]

Создание этого ящика стоило 10млн просмотров в ютюбе! Создай ты действительно классную акустику сюда никто бы не вошел! Молодец мужик!

[@Aadevbali]

Such type of speakers were made by Sonodyne Company but instead of plastic pipes they filled the box with coir and thermocol and cotswool and the output was astounding.

[@b6schilke996]

Just imagine the bass if you used an actual woofer!

[@MrD2118]

Lol

[@tommyweese5697]

Stuff a dd 506 or 606 in that bastard and watch it rattle the hot glue loose

[@ldonnachaidh8084]

And maybe a crossover to filter out anything over 100 hz

[@Baironn]

Отлить захотелось сразу.

[@vanderleymarques2851]

Valeu irmão ficou top e já apreendi parabéns

[@MilVennTV]

Watching here idol sending my love and support

[@ВадимАнтонюк-к2х]

the phase inverter output must be in front, otherwise it will dampen the bass in antiphase with the speaker

[@BorisTrubachev]

в данном чюде, это без разницы😆😂😂😆😂чисто столярно-канализационное видео...

[@spyko7z]

just a waste of materials... no sense video...

[@mariob7791]

The bass is equivalent to that of a semi-open box in which the front sound waves stand out. Rear waves are attenuated by the ultra long ducts (acting as a very low pass filter), so not cancelling frontal ones. This is why most of the sound energy is delivered frontally and centered around the high bass (40 - 60 Hz), close to the natural resonance frequency of the speaker. In this frequency range the box behaves close to a big closed box. The ducts aimed at very deep bass (lower than 30Hz) have no main function in this system, neither the speaker is able to deliver it. All this is a waste of time and plumbing, in my view. And lack of knowledge of minimal speaker building principles either. I will not leave a like which is of course the main aim of this misleading video.

[@gopalt7789]

சிறப்பு தம்பி 👍 💐

[@lanedj801]

I feel like you would want to separate the tube chamber from the speaker because the vibration would be on the outside of the tube and the inside therefore canceling out resonance.

[@sathukumar9509]

மிக அருமையான தயாரிப்பு

[@fivestarrussian]

testin bass wiz song without bass 🤔 great logic

[@ford1546]

the downside of such a long bass pipe is that the sound out of the pipe is delayed in relation to the sound out of the bass speaker

[@AmazonasBiotop]

Yes that is the downside with all pipes/ports. Everyone is used to that sound quality degradation when it is the norm when most of the speakers due to space constraints and the wish of having something small that should sound bigger.. If we on the other side want no compromise and with sound quality. Then skip the ported enclosure go with open baffle and big driver!

[@potsy9973]

I like the no port at all approach best (correct if you guessed sealed;).

[@Egreg.]

Que frecuencia lograste sacar con este proyecto? Hay aplicaciones que ayudan a entonar nuestros diseños

[@AFRIKDIOULASSO]

m.kzbin.info/www/bejne/qXLdhHino7Jpj9k

[@SETHBROTHERS]

This is telent👍

[@gilvansouza859]

Genial parabéns vou tentar fazer um dessa amigo

[@gunjansharma1918]

not good as u people but this system according to me will not boost lf. a folded horn type will be much better option.

[@vorahashimoto6427]

wow awesome sounds like a can drum

[@greatmaster218]

Wouldn't pvc glue make this project a lot easier?

[@ΚεΚάΚι]

Perfect for that amplifier!!!!

[@hksoundpro]

That's an enthusiastic build. The extremely long ports will create excessive planar drag. Group delay will be high. Get a copy of some good software and speak with someone who understands it. If you can model port velocity, mutual coupling, group delay & other easily overlooked parameters, your results will improve dramatically.

[@waynevermilya7169]

There's a reason that deeply tuned sub boxes are big. The tuning on this is no doubt low, but at any volume, the ports will be noisy, and because of the multiple non-smooth curves, they won't be very effective... But hey, it looks cool.

[@krislees976]

k, I'm going to be the one who says this ,.....There is a reason why you don't make speakers like this. You are not going to achieve a responsive and accurate low frequency output. This is a huge gimmick, sorry, I like your imagination but it's clearly without knowledge or to troll people.

[@TimpBizkit]

What is that subwoofer tuned to? I ask because it looks like quite long ports for a box that big, although in a small box you end up needing a really long port just to get a low tuning with adequate port area, which is why many use passive radiators. I've made boxes for 6 x 9 speakers and with 1.1 to 1.2 cubic feet each and 2 2.5" ports I think that were about 8 inches long, the tuning came out around 50 Hz which was low enough for a bass and mid woofer like a 6 x 9. I've also accidentally tuned a big PA speaker to 11 Hz when messing around with ports I had no idea of Helmholtz frequency calculations for (which means it wasn't providing significant boost in the useable range).

[@jasonmelo1974]

With a port that long I assume it's tuned to 5 Hertz 🤣🤣🤣

[@TimpBizkit]

@@jasonmelo1974 in this big a box, you don't need that long a port to get low, especially if it's not particularly wide. The "11 Hz" PA speaker was an H//H Pro 150. I added a piece of cardboard pallet wrap tube to the hole where the bullet tweeter was. Later I entered the paramaters in Hornresp, given the box was just over 100 litres (4 cubic feet). This enclosure will function as a large sealed box, although maybe in the single digits there might be some boost, although the displacement of this driver is likely not enough to take advantage of it. You'd get better SPL just tuning to 40 Hz. Edit: I just did the calculations for 4 cubic foot box with a 4" wide pipe 12" long and it comes to between 24 and 25 Hz in half space. Still too low though for the type of speaker I wanted, which was a party/PA speaker for maximum punch above 50 Hz. Quadrupling or maybe 5 or 6 x port area would have got me there.

[@normanweatherly9475]

My thoughts on this: I do not own a CNC. I would use real wood. I would add material inside the box to minimise dead air space. Finally, I would buy speakers from some company that saves me all the work. My Image 200 speakers from the mid 1980s have excellent bass. Have fun to all the DIY guys out there.

[@davidhamm5626]

What frequency is it tuned to?

[@nigelm.steele9329]

Shroom frequency

[@davidhamm5626]

@@nigelm.steele9329 I like it, posting from Colorado, though it has been a minute since I did some.....

[@mr.gigitix]

Mantap kak... 👍luar biasa...

[@JairPSILVA]

Parabéns achei muito interessante

[@khoperator478]

It's the Best creation.

[@funkmasterflip]

Not gonna work. Sorry, it's a bad build.

[@shidongxu3410]

It's poor quality of phone's bandwidth

[@DeonMakene]

You're here because you're cheap. Want better, buy better.

[@wermebongo1284]

I think I'll just buy one, nice video though 😊

[@kamalkumarthapa4344]

Amazing skill..

[@nunyabidness9691]

seems like its closer to a t-line concept than anything else. i was kicking around a similar idea but instead using 6 inch pvc pipe and fit a 6 inch sub in the end and run about 8 feet of the pipe. im pretty sure that if you have the ports firing the same direction as the sub yours will sound much better than it currently does. as it stands you have opposing waves cancelling each other out.

[@sharoondaniel8889]

Very talented 😊😻😍

[@laligurashvlog]

Best sound 💯

[@maryantoekok1379]

Maybe with transparant board and color led will look nice.. good job

[@Avatarphotography0025]

I need to make my home as mini theater...

[@cachhomevideo1546]

So loud and clear sound

[@jimciancio9005]

Awesome design of your enclosure!!! It would really Kick with a slightly larger Sub or at least a better quality variation of what you placed in it, something that has dual voice coils and a better magnet and basket even if it was kept the same diameter speaker wise would be a huge benefit to take advantage of your great design.

[@mikeonfreeserve2926]

Or buy some TDL Studio 1s like I did. Phenomenal bass response. Try Welcome to the Machine by the Floyd. Have fun!