PARKSIDE Problem Solved for The Smart Battery 8Ah 4Ah

Here you can see the products which i used in this video
BMS for PAP 20 A1, PAP 20 A3 for Parkside 20V Team Power Tool Battery
s.click.aliexpress.com/e/_DFi...
Battery Capacity Test Power Level
s.click.aliexpress.com/e/_DeD...
Heatsink Plaster
s.click.aliexpress.com/e/_Dcw...
- Nickel tape
AliExpress s.click.aliexpress.com/e/_DEh...
In this video I will show how to repair an 8 Ah Smart Battery from Parkside.
All the cells show an equal voltage and are charged, so this is not the reason why the battery does not work.
The problem is the BMS which is blocked and no longer gives a signal to the charger or drill
Thanks for watching . And do not forget, Like and Subscribe
Due to factors beyond the control of CMC DIY, it can not guarantee against unauthorized modifications of this information or improper use of this information. CMC DIY assumes no liability for property damage or damage incurred as a result of any of the information contained in this video. CMC DIY recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of CMC DIY, no information contained in this video will create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from the improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not CMC DIY.

[@supriyo3610]

WONDERFUL Thank you 🙏

[@alyvproduction]

Really interresting video CMC great job 👍

[@CMCdiy]

Thank you

[@orlatris96]

Excelente, obrigado

[@FixitEasyDIY]

Good tip. Thank you 🙏

[@CMCdiy]

No problem 👍

[@aritani2883]

wow cool!!!! 🥰 thank you my friend 🙏your youtube channel good contents 👍 happy day 💓

[@CMCdiy]

Thanks my friend

[@Headcase0570]

I've recently purchased two 8Ah smart batteries but I keep running into an issue with them. I use both of them on the battery-powered grass mower (Parkside PRMA 40-Li C1 IAN420347). Intermittently, the mower will stop being powered by them. You can actually hear the mower blade speed ramping down a step before cut-off. Trying to start the mower again, it'll cut off within 3 seconds. Looking at the Parkside app, the batteries have 0 minutes runtime (despite having been used), aren't overheated (can confirm by touching?) and have a percentage remaining above 80%. Leaving the mower and batteries alone for some time will result in a longer period before cut-off again. I suspect either a thermal issue or bad cells.

[@ZENYOFFICIALCHANNEL]

Wow nice tutorial host I wish I know how about battery and electric thing hehehe

[@CMCdiy]

Thank you 😉🙃

[@TonyMontana-ke2kz]

what battery capacity test power level to choose? "5S lithium battery, full charge 21V" or?

[@wietse5575]

I have 2 4ah smart baterys with broken pcb do they not sell the original pcb somewhere?

[@NoRoads2AllRoads]

Nice where can you get one of those 8Ah?

[@orlatris96]

Olá amigo. Por favor diga-me se esta troca de bms, tem resultado bem? A bateria continua a funcionar bem? Obrigado

[@CMCdiy]

Hi my friend . It works perfectly, just like a classic 2-4Ah battery, only this one is 8Ah with a classic BMS plate, No SMART, and I think it is more durable. As the difference, the classic ones use 18650 cells and the Smart uses 21700 cells

[@nikolaydodev]

Did you try to just reconnect the original BMS to the battery stack? Maybe disconnecting and reconnecting it will force to restart.

[@CMCdiy]

Hi, I tried this too, but without results, the same problem, the red and yellow leds are permanently on

[@06akif-bhv]

Gibt es eine Möglichkeit eine Spannungsanzeige zu installieren statt einer LED Anzeige. Ich würde gern wissen wieviel Volt der Akku noch hat.

[@greenseamussel8018]

Hi, this green-red LED is on problem I have found after refreshing the firmware. The blue line runs till the end during refreshing the firmware, but after it the app wrote: mistake during the refreshing. I do not want to replace the BMS to the 4 Ah old BMS, I want to reset the BMS somehow to use the battery as it was earlier. Can I do anything to reset it? Or how can I solve this problem without changing the BMS to an old 4 Ah battery BMS?

[@CMCdiy]

Hi I think the only solution is a new software, the battery if it is under warranty or not go to the authorized Parkside service for resetting

[@olidevil6666]

Salut tu as pris exemple sur ma vidéo ou tu l.avais déjà fait avant ?

[@CMCdiy]

Hi Oli I started this project a long time ago but I didn't have time to edit it. Then when I searched for a title I also found you. You did a wonderful job and you are very dedicated in what you do.

[@olidevil6666]

@@CMCdiy j ai fais exactement la même chose avec le même affichage de niveau 🙂

[@CMCdiy]

I also saw the method with the burnt resistance. If I get another smart battery, I will study this solution. 🤗😉👍

[@MrKopko2]

Smart batt Smart move Lidl make more money

[@amerikanoss1]

WHERE DID YOU GET THE MEASURING INSTRUMENT I WANT TO GET A TEST METER

[@davey2k12]

Well they still selling the crap battery's in the UK the jokers 😂😂

[@CMCdiy]

Cheap and,, VERY GOOD,, 😂😉

[@marianslovak856]

How about unblocking that BMS instead of just using those batteries? You lost smart functions with this "repair" Here is the fix: kzbin.info/www/bejne/famVZmaeibipqas

[@londoncity1]

Good tip. Thank you 🙏

[@CMCdiy]

Glad it was helpful!🤗