DJI FPV Gimbal! B.A.G & DJI Cams Back In Stock!

[@AndyRCchannel]

Buy Here: bit.ly/2Z0FFTX Caddx Vista: bit.ly/3BVydaP Air Unit: bit.ly/3pgPesp Original DJI Camera: bit.ly/3jgUzvX

[@squaddingquads]

Thanks for the suggestion on this Andy, looking forward to receiving it 😊

[@user-rx8qq8sk9ydv1ce5ib]

Awesome. Would be great to make a detailed video of installing the HT and linking it on a spektrum tx and rx ! Also how the air unit will be powered? Thanks.

[@AndyRCchannel]

Spektrum doesn't have enough range to fly the planes fpv

[@user-rx8qq8sk9ydv1ce5ib]

@@AndyRCchannel thanks Andy. well I have the tx16s and dji remote, so do I need a install a crossfire, and in this case which RX to be used with the tx16s. For dji TX i think it is another story, I am not sure if it could be binded to certain rx. I just got it ready binded to an hglrc cinewhoop and since then I didn't need to do anything. It came with an extra dji air unit that I would like now to use on fixed wing model, but not sure how the control surface 6 channels of the aircraft would be connected to the dji tx. Thanks.

[@AndyRCchannel]

@@user-rx8qq8sk9ydv1ce5ib I would get an elrs module and receiver for the tx16s I have done a video how to set everything up on a tarsnis which is the same for a tx16s although I use Bluetooth for the head tracking which the tx16s does not have but you just use a wire to the trainer port

[@user-rx8qq8sk9ydv1ce5ib]

@@AndyRCchannel thanks a lot. I will check it out. 👌

[@AndyRCchannel]

It's called the ultimate RC plane build. Everything is in there

[@charlesw.3245]

I'd be cool if they made a more compact tilt only unit that would fit in a standard drone camera location (to keep it protected) that's controlled by the accelerometer and gyro. Imagine when your just hovering or slowly crusing/exploring that the camera remains at 0-5° of up tilt and as you accelerate forward the camera proportionally increases its tilt, maintaining optimal camera angle, to 30° plus. I bet you could keep the unit very compact and simple by just using a half or quarter gear attached to the camera tilt mechanism and a tiny geared 5v brushed motor to drive the motion. You may need to incorporate a tiny tilt sensor and processor circuit to calculate and adjust the tilt angle at a high enough cycle rate to keep the system working fast enough for it to be enjoyable.

[@AndyRCchannel]

That's been done before and it makes for a confusing flight experience. It's an option in betaflight

[@JohnDoe-rl9pp]

@@AndyRCchannel DJI drones like the Mavic Pro use that kind of camera stabilization. The only reason it works is because they have a pretty hefty flight controller that's actually flying the drone - the human just tells it what direction to go. It's great for video capture, but less fun to fly.

[@Waffle_982]

What do you do to power the camera? I want to get this but that is the only thing I can’t figure out. The diagram on their website confuses me too, and I’m not sure what to do.

[@lovelyapple7167]

this product is great. I have plan to save as soon as possible to buy it. what is the range of it? how far it can receive signals?

[@jamesturncliff5960]

Mine should be here today. Can't wait to put it on one of my asw28. Just got to save up and get the camera and everything else that goes with it.

[@ktmjay9920]

Just ordered mines, Thanks Andy! Best wishes from ☀️ FLORIDA

[@motionsic]

Thank you Jason for your support. Your Motionsic BAG is on its way!

[@Freebird_67]

If you have Radiomaster let us no if you got it working. I'd like to use buy seems we cant on Radiomaster t16s even adapter didn't work. If you got yours working please let me no. I'd like not to have to return mine.

[@GeorgeCooper_LoneWolf]

Looks very well made and seems to work great Andy. The only thing stopping me from buying one is the cam mount, pitty it did not fit other HD cameras.

[@motionsic]

You can mount the other HD cameras quite easily. Just need to drill a little screw hole 6mm above existing one to anchor tilt gear screw. That’s it. Not beyond the ability of most hobbyists.

[@locoworks8179]

mines on the way too, ordered last week so hopefully not too long, i want to see if the runcam hybrid will fit

[@motionsic]

Thanks for your support! All orders have been shipped within 24hrs except on weekends. The RunCam Hybrids would fit if mounting screw holes are 6mm apart.

[@locoworks8179]

@@motionsic they are 2mm screw size and 6mm apart , the issue could be the height of the unit, the bottom lens is the FPV one and there may not be much down tilt available, even if it fits ok. also the runcam is about 19.5mm wide

[@motionsic]

@@locoworks8179 The width is good. Legit concern about limited tilt down for the Hybrid Cam. Thanks for bringing it up. I am curious if it would work out, also.

[@locoworks8179]

@@motionsic will let you know in a PM on Facebook, i'm the guy that you had to send the PP invoice to. :-)

[@lililililililili8667]

Will this fit the larger walksnail avatar camera?

[@AndyRCchannel]

The walksnail camera is smaller so a couple of spacers should do it

[@aristocraftboy]

Love your work Andy! I love these, I use them myself. The custom Savox servos are silky smooth with no low resolution "stepping" and the tilt servo at maximum tilt up is actually looking straight up due to the lens fov angle, low level inverted looking "up" at the ground is cool lol Great review :)

[@Freebird_67]

You noticed any draft with this headtracker. Mine seems to drift right or left when panning. Like when I stop moving my head the pan will continue a bit more before stopping. Also how did you center pan? Sub trim or ppm center ??? Thanks.

[@AndyRCchannel]

If you watch my ultimate rc plane video it explains how to do that. Are you getting centre drift with the goggles on the ground? U will get that with the goggles on the ground

[@Noah.377]

Would this fit the 03 air unit

[@marcoespana7288]

Saludos 👋 Está muy bien explicado el vídeo. Me gustaría realizar un proyecto similar. Me ayudarías por favor. Que head tracker me recomendarías y como conectarlo.

[@jamesturncliff5960]

great product. still looking for a headtracking unit that will go with my IX-12

[@technoxtreme178]

that bag design is sic!

[@PitsFlyingEye]

Congrats to 80.000

[@VespasianoNevio]

how to move the gimbal with thhe dji remote trough the fc?

[@jamesturncliff5960]

where did you get the bluetooth set up? will it work with a Spektrum IX20?

[@MarkGrob]

I will check this out, from one VR Pilot to the other!!

[@ajking7001]

Nice vid bro. I have a question, i need a this setup for my RC truck what will I need to complete?

[@AndyRCchannel]

You can't really do it on cars as car controllers are too limited in other words their trainer ports can only be used as an output and not an input. But there is a couple of ways around it.. I'll be showing that but it's not easy

[@ajking7001]

@@AndyRCchannel better off wit the GoPro Hero 8 lol thanks for responding looking forward to the new videos keep up the good work😎

[@Dragonewiz]

where can I get the head tracker unit from??? thanks....

[@Dragonewiz]

I WOULD LIKE TO GET THE UNIT FOR THE DJI GOGGLES WIFI FOR THE GIMBLE....IT WON'T WORK WITHOUT THAT ....LOL IF ANYONE KNOWES WHERE I CAN GET IT PLEASE LET ME KNOW THANKS...

[@FourthWayRanch]

how do you stop it drifting?

[@stevenf0]

I love that you made a video for this! I'm excited to buy one. Only three days to payday ⏳⏳⌛

[@Freebird_67]

You have a Radiomaster t16s? If so good luck

[@ScopsLog]

Awesome. Could you (or did you already?) make a video on how to set up the head tracker? I have an fpv set with Caddx polar on an rc car (just with one axis rotation using a servo), but I’d like to hook it up to a head tracker. :-)

[@Rcschim]

This looks like a very sexy solution! Might get me into HT usage (again) Last time I used a HT was in 2009 I think ;) I tried it on a copter once which is super confusing and unneccesary. On a plane however - very nice. Had this slow massive styrofoam diy plane back then wich was a pusher, top wing trainer - super slow and stable - was like looking out of a blimp - great visibility too (but of course with very ugly cam quality back then... greets, Mario

[@motionsic]

Mario, if you would like one to review, please let me know. It’s designed to be a quick install for scale warbirds and EDF jets with foam canopy hatch. An easy way to enjoy scale HT flying from cockpit.

[@tim19368]

hey, which headtracker are you using? thnx

[@michaeltilkens9409]

Its freeking huge cant find anything smaller?

[@pacificnorthwestpilots6050]

Love the packaging!

[@jamesturncliff5960]

Just waiting for my money to get into PayPal I'll be ordering one then 😜 Thanks for the great information

[@shulhi55]

What's the head tracker are you using?

[@AndyRCchannel]

This one :) kzbin.info/www/bejne/noPQqWuhf5mfl9U

[@MOEMUGGY]

Where did you get the DJI bluetooth head tracker for your goggles? Or did you make it yourself with an Arduino board?

[@AndyRCchannel]

It is here kzbin.info/www/bejne/noPQqWuhf5mfl9U

[@MOEMUGGY]

@@AndyRCchannel thank you (y)

[@thenatedog]

Just ordered one!

[@bobturner3388]

Excellent product, professional grade thru and thru! I have multiple!

[@MCsCreations]

Awesome review, Andy! Thanks! 😃 That's a really great option!!! Stay safe there with your family! 🖖😊

[@mpojr]

very very good l am still learning Andy

[@pettz18]

Hey Andy is it possible to extend the cable between air unit and dji camera? or is it only possible to do it on the vista unit and vista camera? (like going up from 8cm to 20cm)

[@Inertia888]

Yes, AirUnit is actually a bit easier to do.

[@elouiseeverett3986]

Excellent review. Thanks!

[@rainriver1]

Will they ship to the United states. I live in Pensacola Florida. Love your vids man!!!

[@AndyRCchannel]

They are based in the United States so yes :-)

[@rainriver1]

Thanks for the reply my freind, I flew my old 1.5 meter eflite Timber that ive had for yrs and flying analog fpv with but have switched out with caddax air unit and dji v2 goggles and flew my first ever flight with HD 3/20/22 and WOW!!! I love it!!! Will convert my old SU-26 next.

[@AndyRCchannel]

@@rainriver1 nice I'll look out for that

[@jamesturncliff5960]

I like mine well built heavy duty compared to some other builds I've seen

[@jamesturncliff5960]

I got one I plan on getting two more

[@AerialWaviator]

Looks like a nice solution. Think putting it on a quad copter (3:50) might be more interesting experience than expected, unless flying is a stabilized mode. At least for me. 😂 Maybe less daunting to keep quad level, if quad was using INAV, and could put into position hold. This could be fun.:)

[@AndyRCchannel]

You got it 🙂

[@rctom1]

Hey , Andy Rc , pls can you tell me why i need 4,5 h to upload a 5min. vid to YT ? Hope you´r fine , not need the MS bag, lol .

[@runpuppyfpv5744]

Wow that is really cool

[@benjaming9835]

Looks very nice but it’s a bit pricey. I have to save my UAV money for vistas.

[@diystuff5628]

Didn't spare a second ..got a cam to replace that crappy nebula nano

[@karlosio1]

Nice gimbal, how much does it weigh?

[@AndyRCchannel]

106g with vista

[@mauritz1774]

THX after you Made the Video with EDF Jet and Laserbeam I Must spend now 250€ for new 3d Printed RC Airplane. Bring me not on Expensive Ideas

[@runpuppyfpv5744]

Shame it doesn't come with everything u would need to use it tho

[@AndyRCchannel]

I think he's working on that. Really had to do when everyone has different gear

[@runpuppyfpv5744]

@@AndyRCchannel Yeah I bet it is that would be cool on like a 7" lr cruiser

[@igeekw2u]

90usd for a gimbal! Really?!!! Are they nuts or are they nuts????! That's what my 3d printer which is spitting out gimbals from thingiverse costed!

[@savagebrian1234]

was so excited till i heard the word servo;(

[@fellpower]

90 bucks for some plastic parts? Sorry Andy, i like you very much, but thats too expensive, for what u get

[@AndyRCchannel]

I agree. its because its a very niche product. Hoping I can change the popularity of this. check out my ultimate rc plane build for much cheaper option

[@Freebird_67]

Plus it's not entirely compatible with Radiomaster t16s Mk1 without heavy mods to radio. If I'm going that route I'd just build the entire system myself for 1/4 the price. I'm hoping I can be proved wrong that it can actually work with Radiomaster t16s hall Mk1 hardwire or other but I sure haven't seen this happen yet.

[@PiDsPagePrototypes]

$90 (assuming US) for molded parts plus servos, all the design and engineering already done, sounds cheaper then the time and parts to print my own. Price will drop if it makes consistent sales, expect it to be cloned pretty quickly by companies that ignore intellectual property rights.

[@PiDsPagePrototypes]

​@@Freebird_67I have the same Tx, could you explain more on the incompatibility issues? Head Tracking camera mounts are on my purchase list for the new year. Getting back in to fun flying fixed wing from cine drones.

[@쨈따방송]

오와 드론 머찌당!@ 사고 싶당