Dji Inspire 1 Crash Repair and Assembly broken carbon fiber boom - Tutorial

[@TheSecretVault]

I notice that on your test flight when aircraft nose is facing video camer there is a noticable angle of the blades tilt away from body of drone. do you have much experience with what the best setup is, small tilt or large tilt. Which do you find is better.

[@CosmicSoundMDB]

How did you managed to put out the Old broken ends of the tube, to place in the new one? Those are quite strong glued in place. i am in same situation I need to fix my left broken leg. And all Ive noticed upon opening the leg, is that there is plenty of glue between the leg holder and other parts along the tube, how you toke those apart?

[@jasonsitz3056]

ive been building the inspire 1 and the only parts im lacking is the two boom arms for both sides, batt buss, batt remote 4motors and im finished your videos will help a whole bunch thankyou. also do you have any parts like the srews and bolts or the arms or even point in the right direction. thanks for any help gret videos

[@jasonhd100]

Good job. I bought my Inspire 1 with two broken motor boom arms replaced them and many other parts.Got it flying. Then my friend crashed into me with his Syma X5C. Had to replace anther motor boom arm.

[@kevincabral5787]

What's the clear plastic you put inside the tube before putting in the red and black motor cables?

[@DavidVogt]

Thanks for this video. When trying to pull the antenna cable trough, the top 1/2 inch tore off. Now the cable is too short. Any advice? Thank you so much.

[@MatteoGalet]

Hi, we do have replacement cable! Slightly bigger, but better quality though. Contact info @ heliengadin . com

[@WeBeYachting]

Nice video mate, thumbs up. Cheers from the IGY Simpson Bay Marina, Sint Maarten in the Caribbean.

[@heliengadin5086]

Thank you mate! All the best from Swiss ;-)

[@heliengadin5086]

I was just wondering...how many of you had a crash with our beloved I1? And what kind of damage did you get? Were you able to solve the issue on your own?

[@DavidVogt]

I...how do I say this. I ran over mine with my car. Put it behind the car to put it in the trunk, went to grab something else, got in the car and backed up......*crunch* Thankfully the damage could have been much worse. All I need to do is replace all 4 feet. The carbon fiber tubing and camera are all fine. We'll see how that does, but this video was very helpful - thank you!

[@heliengadin5086]

Hi there! You´re welcome David, glad to hear our video has was helpful. All the best!

[@andreaspreafico2262]

Have you crashed your drone over San Gaudenzio church? Because there I've seen some pieces of an Inspire One

[@davidalan2469]

When you smash the dielectric in coaxial antenna cable you change the impedance. Don't pinch too hard.

[@MatteoGalet]

Nice observation, the operation is quite tricky. We test the cable + antennae VSWR after repair though, to be sure everything is fine.

[@cyurdown7096]

Hey were you buy the carbon fiber tube

[@MatteoGalet]

Hi choo yang, for our works we source CF tubes from an italian supplier, Clitber Tecnology. You can find them on eBay. We also offer repair service for any kind of drone.

[@rajiri1]

Can you give the size of the tube that goes inside, thanks

[@heliengadin5086]

+bob ingham Hi there Bob! It's 20 mm

[@rajiri1]

+HeliEngadin thanks

[@edelson1971]

where can i buy a complete arm?

[@heliengadinstmoritz624]

+Edelson Silva You can get it from a Dji dealer in your country

[@edelson1971]

+HeliEngadin St Moritz I will try to find. thank you!

[@TurboHeart]

GREAT video

[@heliengadin5086]

+Turbo HEART Thank You!

[@elvisbest3213]

good job sir

[@TMinTokyo]

Good video,but I hate this music.