Engine swap would mean you SHOW AN ENGINE SWAP! That's 5 minutes of my life I'll never get back...
@MattShonan2 жыл бұрын
Well, there is not much to show as you say, quite quick to do! Bu why you might need to do that is what I thought is valuable to share. Let me know what you like to se in future videos and I might be able to incorporate suggestions. Have a nice day! 😊
@DArkwIng23 жыл бұрын
Never land on ground always takeoff and land from/on hand
@MattShonan3 жыл бұрын
Yes, that is the only way at the beach. 👍🏻😊 Thanks for the support! Have a great day!
@SirensAndAlarmsOfNorthernIL2 жыл бұрын
Or use a helipad
@milo-WT7 ай бұрын
Is it possible to add a more powerful motor onto the dji mini 2 se to make it faster?
@MattShonan6 ай бұрын
I would not do that since the software can not be adjusted for that. FC and ESC still will think the original motors are on the Mavic.
@milo-WT6 ай бұрын
@@MattShonan ah ok thanks, im building an fpv drone now so i dont need to worry about the performance on my dji.
@MattShonan6 ай бұрын
great! @@milo-WT
@aldrinjude4 жыл бұрын
Have you tried spraying it with wd-40 or blowing compressed air to it?
@MattShonan4 жыл бұрын
aldrin jude Dagmang Yes, it cleaned up some but not 100%. That is why I decided to replace the engine.
@themaximussx8753 жыл бұрын
@@MattShonan you can get rid of the sand just keep cleaning. Use diesel in a bucket . Motor in you hand and with shaking movement submerged in the diesel wash it out. It will be out in few minutes. Sometimes rotate the motor and keep up with the flushing. 10min all as new. Clean with alcohol... Done
@prodbydramatic3 жыл бұрын
@@themaximussx875 wow thanks
@philldownes86852 жыл бұрын
ok . get some electrical spray cleaner.. get the motor ready to start up and geta compressor handy with around 150 psi coming through a jet that is needle size.. now start motor with aire going through at 25 psi and then spray in some electrical cleaner. then with motor running slow add some more cleaner then straigh taway blast with 150 psi from compressor, this would shift it if its sand.
@MattShonan2 жыл бұрын
In some cases this can work! Just if at the beach sand and in this case some iron partials are involved it might requite an engine replacement. Thanks for the comment and have great day!
@-lowdown-46982 жыл бұрын
I just had my maiden flight on the beach and I crashed my Mav mini into granite rocks then it landed in the sand lol, no cracks on the body or arms, props ok but two motors stopped and sounded like yours I took it home took props off and used my car tyre compressor and blew it inside the mother every angle whilst turning the motor the grinding noise went and it span around freely, once turned on they span around so props back on, no problems, sometimes sands damp and sticks inside either pressure blow it out if u can't let the sand dry then blow & blow inside whilst turning before taking apart, Im a total novice lol I think I was lucky, I was gutted at the time it bounced off one boulder onto another but I think my leg extensions you connect from the front Arm to the back arm so it's like a sledge & I had a gimble guard on protected the body ✌🏼
@MattShonan2 жыл бұрын
Great you could recover that way without a major surgery! Yes, it can work! I think in my case there were iron or other metal things mixed in the sad and in this case it is really game over. When looking at my other FPV quads, I had another sad case recently and how I recovered form this will be up here sometime in the next weeks or so. I use there a different method since the motors are more expensive and no metals were in the sad which got in the motors. Happy flying! 🤙🏻
@KTPDAILY2 ай бұрын
😅 @@MattShonan
@erikaertsen Жыл бұрын
Matt! question: what is the name of the wraping on your drone? And where can you buy it?? I realy like the grey one in the background Its great!!! Greetings Erik
@MattShonan Жыл бұрын
Thanks for asking, it is from www.decalgirl.com Have a great day!
@goasfarasyoucansee2 жыл бұрын
I fixed my in 1 hour
@MattShonan2 жыл бұрын
Great !!! 👍🏻😊
@goasfarasyoucansee2 жыл бұрын
kzbin.info/www/bejne/qZfEkGyciJh1jLs
@NabeelAhmed-me4ok4 жыл бұрын
where did you find motor replacement parts. please leave a link below. i only need a motor. i dont need a arm.
@MattShonan4 жыл бұрын
Nabeel Ahmed I bought mine on ebay. however, I also could not find only the engine and had to get the arm assembly. The price would not change by much. Amazon also has replacement parts available, you can try it there as well. Thank you for watching and the support, have great day!!
@NabeelAhmed-me4ok4 жыл бұрын
What did you write i can not find it anywhere. Can i please get a link as well?
@iLuSionModDerI Жыл бұрын
I need help... The right arm motor is very hard, it's not turning as well as the others... is there any product or liquid I can throw in it?
@MattShonan Жыл бұрын
Yes, I have a video on this coming up next week. You can try to first wash the motor down with clean hand warm water. After that, give it an alcoholic bath to push the water out. Then dry it out for some days and hopefully you will be fine.
@MattShonan Жыл бұрын
regarding alcohol bath you can also check out this video kzbin.info/www/bejne/qoauYWB3arR3nq8
@MattShonan Жыл бұрын
The video how to recover my clocked up motors is coming up end of next, I will post a link to that once it is up. Have a great day!
@iLuSionModDerI Жыл бұрын
Thank you!
@MattShonan Жыл бұрын
@@iLuSionModDerI you are very welcome! 😊
@Dr.Gunsmith3 жыл бұрын
That motor sounded like my knees 😂
@MattShonan3 жыл бұрын
🤣👍🏻
@AviAero1233 жыл бұрын
Just remove the C clip and you can have access to the rotor containing the magnets easily...... I've done this many times
@MattShonan3 жыл бұрын
Thanks for your comment!
@DarkstarNovembr3 жыл бұрын
how the heck do you separate the M2P motors though. there's no circlip. are they press fit?
@MattShonan3 жыл бұрын
@@DarkstarNovembr good question! I could not figure it out either.
@ToothlessFPV2 жыл бұрын
How to you remove it on the mini motors?
@dangerdoberman3 жыл бұрын
The sand grinding in the motor gave me anxiety.
@MattShonan3 жыл бұрын
definitely! :)
@Quasar_airborne Жыл бұрын
Hi where to order the silver cover motor
@MattShonan10 ай бұрын
the vendor where I got them from discontinued to sell them but there are several sources still having stock. you can try Amazon or Aliexpress.
@JourneymanVan2 жыл бұрын
Which motor your drone has Brushed or brushless? Thanks
@MattShonan2 жыл бұрын
All brushless once!
@grik46662 жыл бұрын
How much it cost to repair a motor
@MattShonan2 жыл бұрын
Well, it really depends where you get the motor. It can be very inexpensive if you find a good deal on eBay for example. Thanks for the comment, happy flying and have a great rest of the day!
@alexmontoya72583 жыл бұрын
The ad assuming I’m a homeowner
@MattShonan3 жыл бұрын
Google get things wrong sometimes, thankfully 😊🙏 Have a great day!
@sousarogers3 жыл бұрын
You had to clean with compressed air
@MattShonan3 жыл бұрын
I really tried! But is was not possible to get all sand out and that is why I decided to make this engine swap project. Hope you enjoy my videos and have a nice day!
@handalboy4 жыл бұрын
So do you just solder the cables from the new motor to the cables on the drone?
@MattShonan4 жыл бұрын
That is correct! I soldered the new cables and the the once form the old motor together. To avoid taking the Mavic are apart and not solider directly to the mainboard of the Mavic. Reason, this drone is tiny and I tried to keep soldering heat away from sensitive electronics like the IMU.
@martin900003 жыл бұрын
Won't the engine covers push the weight above 250 grams?
@MattShonan3 жыл бұрын
Correct, they do, same as ND filters. If you like to stay below 250g you can not use any accessories like that.
@martin900003 жыл бұрын
@@MattShonan Damn, I was hoping that wouldn't be the case.
@MattShonan3 жыл бұрын
@@martin90000 you can try to make up for the more weight by using carbon fiber propellers. The other option you have is using the Japanese batteries. In Japan the Mavic Mini has 199g. DJI is doing that by just downsizing the batteries. Using those batteries you can shave off 50g. However, your flight time will be impacted by that.
@martin900003 жыл бұрын
@@MattShonan Interesting, do you know where I can get carbon fiber propellers?
@MattShonan3 жыл бұрын
many places, just make a quick google search. At the time I got mine Amazon had a good deal.