Dodge Transmission Swap (Auto to Manual) PT 2

  Рет қаралды 32,460

J_Moffitt

J_Moffitt

Күн бұрын

Пікірлер: 35
@PeacefulMotoTrailz
@PeacefulMotoTrailz 11 ай бұрын
Couldn't have helped more!!!! Thank you so so much!
@johndoeed1961
@johndoeed1961 4 жыл бұрын
Awesome info! I plan on swapping my 47re to an nv56 in my 24v 00 3500
@j.c.smithprojects
@j.c.smithprojects 4 жыл бұрын
not 1 crack in that dash! little by little she is getting there. combination u-joint available?
@j_moffitt
@j_moffitt 4 жыл бұрын
Can’t have cracks if there isn’t something to crack haha and yes I’ve already got the correct u-joint for the front
@yo6669991
@yo6669991 4 ай бұрын
How are the holes made?
@amezyy1713
@amezyy1713 4 жыл бұрын
How was it installing your slave cylinder in the bellhousing I haven’t installed myn yet but it dosent go in all the way Idk if it’s hitting those plastic tabs on the sides or my clutch fork is back to far but it won’t go forward anymore so
@j_moffitt
@j_moffitt 4 жыл бұрын
It’s gonna be under pressure but I managed to get it in far enough to get the bolts on and then snugged it up
@gabesmith2016
@gabesmith2016 Жыл бұрын
Approximately how long did this take, hours wise.
@j_moffitt
@j_moffitt Жыл бұрын
Assuming you have all the parts/equipment needed, 10-15 hrs
@TimeAlone8
@TimeAlone8 6 ай бұрын
I got a question should I leave my standard 95 long bed alone or do an automatic I’m new to the standard but wanna learn but want to restore the truck to the best condition possible is automatic bad or good for dodges
@j_moffitt
@j_moffitt 6 ай бұрын
Can’t go wrong with a built 47re or 48re
@TimeAlone8
@TimeAlone8 6 ай бұрын
@@j_moffitt gotcha thank u man may god bless u🙏💯
@j_moffitt
@j_moffitt 6 ай бұрын
Nothing wrong with the 5 speed either, just need to add a 5th gear fix
@scrappydog175
@scrappydog175 Жыл бұрын
I know I’m late here but can you tell me if a rear drive shaft out of an automatic would fit in the exact same 2nd gen 2500 manual transmission?
@j_moffitt
@j_moffitt Жыл бұрын
Negative, different lengths and possible to have a different output splines
@scrappydog175
@scrappydog175 Жыл бұрын
@@j_moffitt thank you
@Itsa_Mea
@Itsa_Mea 4 жыл бұрын
4:27 Black vacuum line is disconnected
@j_moffitt
@j_moffitt 4 жыл бұрын
Yeah I noticed that
@Itsa_Mea
@Itsa_Mea 4 жыл бұрын
@@j_moffitt yeah I wasn't being smart ass, I just thought you missed it because in the video you were saying you had them all hooked up. You have plans on swapping to hydraulic assist for the brakes? My friend has a 95? with vacuum booster brakes I'd like to swap so a video would help.
@j_moffitt
@j_moffitt 4 жыл бұрын
I think one is missing completely but I was referring to the lines around the trans, and no plans for the hydro boost as of now
@shanewright6958
@shanewright6958 4 жыл бұрын
Great job 👍👍🇨🇱
@joeponder9668
@joeponder9668 4 жыл бұрын
Short video is better than no video brother!!!
@joeponder9668
@joeponder9668 4 жыл бұрын
Hey bro watching your video, you think pan hard bar is better or easier than 4link? I’m fixing to pop a 1 ton under my 1/2 ton truck and wanna run bags and a valve like you did. Not hauling hella weight on the reg like you do either just a boat here be there. I’m mainly swapping for the disc brakes and 410 gear set. And mine has 350k on it as well.
@j_moffitt
@j_moffitt 4 жыл бұрын
Well a parallel 4link will need a panhard as well. A triangulated setup does not need a panhard
@tedbownas2748
@tedbownas2748 4 жыл бұрын
Can you borrow the pinion yoke off the other truck?
@j_moffitt
@j_moffitt 4 жыл бұрын
I thought about it but I already got a u joint for it
@daytonheath180
@daytonheath180 2 жыл бұрын
So you can’t use the transfer case from an auto?
@j_moffitt
@j_moffitt 2 жыл бұрын
Different input shaft
@juanmanuelcervantes3755
@juanmanuelcervantes3755 3 жыл бұрын
The transmission must be level ? or how do you figure thanks
@j_moffitt
@j_moffitt 3 жыл бұрын
I don’t understand your question
@juanmanuelcervantes3755
@juanmanuelcervantes3755 3 жыл бұрын
I'm doing the crossmember on 1995 dodge ram 2500 installing the zf6 transmission
@j_moffitt
@j_moffitt 3 жыл бұрын
Pinion angle and the yoke from the transmission should be equal opposites. So if the pinion is a positive 3 degree angle, the trans yoke should be a negative 3 degrees
@juanmanuelcervantes3755
@juanmanuelcervantes3755 3 жыл бұрын
Hey thanks a lot for taking your time to answer my questions thank you buddy
@brandonburkowski5372
@brandonburkowski5372 3 жыл бұрын
Is the tcase from an auto trans?
@j_moffitt
@j_moffitt 3 жыл бұрын
No
Dodge Transmission Swap (Auto to Manual) PT 3
7:46
J_Moffitt
Рет қаралды 17 М.
Dodge Transmission Swap (Auto to Manual) PT 1
10:41
J_Moffitt
Рет қаралды 65 М.
Что-что Мурсдей говорит? 💭 #симбочка #симба #мурсдей
00:19
СИНИЙ ИНЕЙ УЖЕ ВЫШЕЛ!❄️
01:01
DO$HIK
Рет қаралды 3,3 МЛН
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
94-02 Dodge Cummins 47re to NV4500 Swap: Part#1
14:21
Schneids15
Рет қаралды 16 М.
The cheep and east way to manual swap your 5.9 cummins
17:57
AirHeadPerformance
Рет қаралды 17 М.
NV4500 Transmission Teardown & Inspection (Part 1)
30:21
Torque King TV
Рет қаралды 61 М.
Torque converter in a manual transmission - will it work?
15:05
Garage 54
Рет қаралды 728 М.
Grand Cherokee ZJ Manual Transmission Swap Part 1
17:39
Low-Buck Garage
Рет қаралды 36 М.
EVERY PART YOU NEED TO MANUAL TRANS SWAP YOUR CUMMINS
20:34
V-BELT and SON
Рет қаралды 68 М.