Restoration Hydraulic Car Jack. Repair jack that leaks fluid. Restaurare cric hidraulic. Reparare cric din care curge uleiul.
Пікірлер: 227
@carmelpule69542 жыл бұрын
In my opinion, only 5 minutes out of 25 minutes were used to cover the clever parts of the Hydraulic unit while the high-pressure cylinder was not taken off/dismantled to show the final ball valve in it. In fact, none of the ball valves were shown. most of the time the video showed the use of a wire brush removing the paint and a few coats of undercoat and topcoat were shown including the assembly which is not really very difficult.. The last one I overhauled had four-ball valves used as follows. a. One ball bearing valve for the return release path. b. Two ball-bearing working in unison to produce the pump9ing action.' c. One ball bearing with spring loading to act as a high-pressure relief valve. This hydraulic jack is interesting and careful tightening is required as when one tightens the top nut to push down the reservoir outer cylinder, the central high-pressure cylinder is lifted up, and if it is not tightened extremely tight it could lift a little and leak at the lower copper seal which also holds in place the final ballbearing high-pressure valve.
@DorelBorlea2 жыл бұрын
My intention was to fix this jack and make it look better. I didn't want to disassemble all the valves because there were no problems with them. If I had disassembled all the parts, the video would have been more interesting, but making such a detailed video takes a long time and I tried to make it as short as possible. Thanks for the comment. I will take into account your opinion for the next videos.
@miliady2 жыл бұрын
@@DorelBorlea where are you from? how can i contact you as i have a floor jack like this that i would like to repair as it is leaking everywhere
@j.rothchild1732 жыл бұрын
Good job! Awesome 80s jams, too!!!
@DorelBorlea2 жыл бұрын
Thanks!
@ferdinandcalixton1559 Жыл бұрын
Hm does it cost for the labor price please?
@PinBall33 жыл бұрын
Good Restoration On The Jack I Have The Same Model In The Green Color I Got New In 1993 From Sears Still On Its Original Seals And Lifts Like A Champ To This Day
@bonifaciojose674 Жыл бұрын
What is the model number please?..
@PinBall3 Жыл бұрын
@@bonifaciojose674 Sears 328 Series Find info on Hcrcnow dot com www.hcrcnow.com/uploads/drawings/sears328seriesjacks.pdf
@pcofranc Жыл бұрын
@@bonifaciojose674 I have a Sears Floor Jack mfg 08-1990 Model # 214.50112 Two common model groups are #325 and #214 but #325 seems to be way more popular for rebuild kits. I think I will go to a local hydraulic seal shop and get a new piston o-ring and one for the round vertical pump shaft as nothing else leaks. I also have a harbor freight aluminum Jack US General brand Item # 91039 1-1/2 ton 3,000 lbs that purchased new in 2003 and the piston leaks a bit and needs a new o-ring.
@wmoy8507 Жыл бұрын
Great job. It looks like the same jack I bought about 35 years ago and was working until recently. It probably needs new fluid. My concern is the o rings you use. I think the material is buna which I believe is not compatible with hydraulic fluid. Doing some research your should use viton o rings which is long lasting exposed to hydraulic fluid. Do not know how long your replacement seals will last.
@jamesross1174 жыл бұрын
Very good! This is a complete tear down and reassembly of a floor Jack. Other videos are just periodic maintenance. Thanks for doing this.
@robpeters52044 жыл бұрын
I have one exactly like this one. I bought mine in the early 90's works great still.
@DorelBorlea4 жыл бұрын
It's a very good jack. I am very pleased with it.
@thomasbardwell41514 жыл бұрын
I also have the same jack MVP speedy lift 3 ton BUT I CANT FIND THE KIT ..DO YOU HAPPEN TO KNOW THIS KIT NUMBER ON THE JACK ON THIS VIDEO?
@acatsaid54113 жыл бұрын
@@thomasbardwell4151 did you ever find out?
@PinBall33 жыл бұрын
@@acatsaid5411 Try This Here ? > www.hcrcnow.com/shop/seal-kits/mvp-by-shinn-fu-america Good Luck
Can you tell me what measures are the o ring than those for the cylinder
@921aa4 жыл бұрын
The pump and ram are the the o-rings hat wear out and cause the jack to fail. It doesn't look like you replaced either.
@DorelBorlea4 жыл бұрын
I just replaced the gaskets are they were broken. A valve was clogged with a piece of gasket and that is why the jack went down.
@hishamchohan4942 жыл бұрын
Hi,you did a nice job in restoration but the main thing is hydraulic repair... You did not remove the fluid tank cylinder from the mian. And the oil plug must be up side ...see other videos of china jack
@santy10304 жыл бұрын
very Good.
@Mr572u4 жыл бұрын
You left the main frames in primer? After all that prep work? Man......
@JoseDiaz-tf4su3 ай бұрын
En qué tienda compra los empaques
@braulioalvaradomadrueno42916 ай бұрын
esta excelente el tutorial solo que me parece muy rapido y no deja apreciar paso a paso la reparacion , me gustaria que no incluyera lo de la pintura mejor darle mas dedicacion a lo que es la reparacion
@valmeronsales32834 жыл бұрын
Very Very good beautiful
@DorelBorlea4 жыл бұрын
Thanks ! I'm glad you liked this video
@ignacioanaya34036 ай бұрын
very nice job
@DorelBorlea6 ай бұрын
Thanks
@DerMoelly2 жыл бұрын
Thanks for your great video! With the video you convinced me to buy the same *"Hein Werner O'Boy"* , which, however, has lost oil. Your video showed how easy it is to set up the jack! Greetings from Germany!
@simonilett9984 жыл бұрын
Looks good👍 But how do you fill the oil now? You assembled the cylinder with the oil filler plug at the bottom??....LOL
@DorelBorlea4 жыл бұрын
Thanks! I will turn the hydraulic car jack upside down and add oil through the filler plug. In my opinion the oil filler plug must be placed at the bottom.
@simonilett9984 жыл бұрын
Ok sure, that should'nt make much difference. Every other trolley jack I've seen (including your's - before you pulled it apart) has the plug mostly upwards, so it can be filled to the correct level in it's operating position??.. and i guess it would save the oil plug getting knocked out while rolling on some uneven surface etc...nice oil leak everywhere....lol
@DorelBorlea4 жыл бұрын
At this jack, to feed oil through the top you have to disassemble the upper arm. If you think there is a risk that the oil plug will pop out accidentally then you mount it on top. Do what you think is best for you.
@mariosciore35272 жыл бұрын
great job where can you get the O rings for it to rebuild it
@hamrhal Жыл бұрын
In a plastic tub, with a whole bunch of others. sort through and pick one. @ 5:00
@SharpObserver1A24 күн бұрын
En amazon, por approximadamente 35 Dolares un juego de empaques, son carisimos y solo usas la mitad de los empaques.
@adeltaibi40034 жыл бұрын
Good job 👌👌👍👌👍👌
@DorelBorlea4 жыл бұрын
thanks!
@user-bz5nq2yi9m Жыл бұрын
Potevi verniciare anche il lato interno, invece di lasciarlo grigio.. .. complimenti bel lavoro
@DorelBorlea Жыл бұрын
Ho dovuto aspettare un altro giorno perché la vernice si asciugasse. Avevo un po' di fretta. Anche a me sembrava buono.
@boblamb84212 жыл бұрын
Great video. I have a Larin 6000 pound floor jack. The company says they don't have a rebuild kit for it anymore. Where can I buy a kit for my jack? It actually looks like a Craftsman jack. I've looked at the insides of many old floor jacks I could have repaired had there been seals for it. I find it hard to believe the piston rod seal is different in all jacks. My guess is it's the same one in every kit. Any help can save a very usable older jack.
@hishamchohan4942 жыл бұрын
O-rings and steal balls..etc.,and atf or hydraulic fluid
@hishamchohan4942 жыл бұрын
Hi, please go to a local hydraulic repair shop and they can help you,... You can find main piston hydraulic seal blue color or they can custom make one for you if they can .. O
@spelanalys3 жыл бұрын
I have an old jack, same model as yours. It works, however when I want to release the pressure and lower whatever I'm working on (usually my boat on a trailer) - it always comes down with a boom. What can I do so pressure is released little by little and the boat is lowered smoothly? I try to turn the screw/handle as slowly as possible of course, but it doesn't help.
@DorelBorlea3 жыл бұрын
I think the trailer and the boat are too heavy for this jack and because of this the jack goes down very fast.
@spelanalys3 жыл бұрын
@@DorelBorlea Hm, you think? The boat is only 900 kg. I don't remember how much the jack can take but is seems like a beefy piece of equipment. It's really heavy.
@DorelBorlea3 жыл бұрын
The maximum load is 2 tons. Try to lift a car and you will see that it will go down more slowly. You have to untie that handle very slowly and wait for it to come down.
@danielmartinezperez48842 жыл бұрын
Q vídeo tan inofisioso ....
@abdongregorioruizmaldonado83334 жыл бұрын
Gracias por compartir Dios te bendiga .pregunta donde condiges los empaque o ligas
@DorelBorlea4 жыл бұрын
Dios te bendiga. Tengo un tractor y le cambié muchas juntas. Entre esos sellos encontré algunos que se ajustan a este gato.
@chanthysok25484 жыл бұрын
@@DorelBorlea.
@SeeMooreVids4 жыл бұрын
Nice. I’ve got and old jack, looks similar I’ve been wanting to rehab. Has leak. A Hein... O’Boy. Something like that. Thanks
@ytuhcsna4 жыл бұрын
I have an O’Boy which I love. It needs a fluid fill and I can’t find the place to add fluid. No little rubber plug on the cylinder. What to do?
@brandonfeils68834 жыл бұрын
@@ytuhcsna look at the pdf on this site. www.hcrcnow.com/shop/seal-kits/product/1301
@rickyhensley62364 жыл бұрын
@@brandonfeils6883 were u get the parts n wat 2 ask 4
@brandonfeils68834 жыл бұрын
Ricky Hensley follow the link above
@tomlakeandriver76703 жыл бұрын
Hello and thank you for sharing, however I have the same jack that I am redoing that I have for over 20 years. In the part of the rectangular block or this troube the farmeture piston there are small balls in each compartment can you tell me where it really reopens because by wanting to empty it the whole is to fall.
@DorelBorlea3 жыл бұрын
There are steel balls in the piston compartment and in the overpressure valve compartment. But I didn't understand what you meant in the last part of the comment.
@wilberrondinelcordova44384 жыл бұрын
Donde queda el taller de mantenimiento de Gata hidráulica
@DorelBorlea4 жыл бұрын
Compré este conector defectuoso y lo reacondicioné. Cambié las juntas defectuosas. El gato funciona muy bien ahora.
@lionden42 жыл бұрын
This guy have a of patience…. 😊
@thaddeauscaldwell71014 жыл бұрын
Thank you for the great video. I bought this same jack a couple days ago from a friend for $10. The jack will jack up but won't go down when I try to turn the handle. The handle won't turn. I took off the lower sprocket but the bolt that let's down the jack won't turn. You did the repair @4:35. Do you know how I can fix this issue ? Any information is greatly appreciated. Thank you.
@DorelBorlea4 жыл бұрын
it's probably stuck, you should disassemble that part and remove the bolt and grease it
@VinnieVega764 жыл бұрын
Fantastic restoration! Question though. Do I have to go through that entire process just to get my jack to work, or can I just bleed it? One hell of a great job you did there I have an old one too that does exactly that, but do I have to remove everything like you just did? You're probably going to tell me that the O-ring is shot
@DorelBorlea4 жыл бұрын
This jack had oil leaks. There were some leftovers from a broken gasket. To remove the cylinder you have to disassemble the side parts. Analyze carefully and see what the problem might be. In this video I did not show how I cleaned the blocked channels.
@VinnieVega764 жыл бұрын
Thanks
@jorgemelendez95462 жыл бұрын
To much work but well done worth it
@DorelBorlea2 жыл бұрын
Thank you!
@kevinlamarr14244 жыл бұрын
I have an old jack that fits under the bumper like the air jack in a truck repair shop. I bought it to restore it. I’m hoping that place has a kit for it. Thanks
@DorelBorlea4 жыл бұрын
I also like to repair and restore things. It would be interesting to make a video with the jack restored by you.
@kevinlamarr14244 жыл бұрын
Dorel Borlea Thanks for the interest! I’m a truck driver and I’m just getting started making videos. I have a jack just like that one that I’m going to restore. I also have a 1984 Winnebago chieftain 33 that I’m working on. Not an expert by any means but I wanna do it with my little 5-12 year old nieces and nephews.
@DorelBorlea4 жыл бұрын
It's a nice way to spend your time. The satisfaction is very high when you manage to repair something. Especially if you have some children around. Good luck.
@kevinlamarr14244 жыл бұрын
Dorel Borlea Thanks 🙏 I’ll let you know when I get started and post a video I’m on the road full time so I move kind of slow
@victorperalta6244 жыл бұрын
Todo muy bien Pero le pusiste el tapón del aceite por abajo y va por arriba
@frankinga3120 Жыл бұрын
Would have been better if you had replaced all the seals, and greased all the friction areas; also did you run out of orange paint?
@DorelBorlea Жыл бұрын
I had to wait another day for the paint to dry. I was in a little hurry. ;)
@sambou78112 жыл бұрын
Good job
@DorelBorlea2 жыл бұрын
Thanks !
@kasemfalahkasemfalah67492 жыл бұрын
Thanks
@GLADIADOR007774 жыл бұрын
Todo el video pasa tan rápido que no ofrece mucho mal video
@DorelBorlea4 жыл бұрын
La duración original del video es de 2 horas. No creo que nadie vea un video tan largo.
@maximoaguilar88543 жыл бұрын
Disculpa donde puedo conseguir el quit de reparación por tu atención gracias
@robertomena2111 Жыл бұрын
Donde puedo conseguir las refacciones de los gatos?
@DorelBorlea Жыл бұрын
No lo sé.
@dim40513 ай бұрын
Здравствуйте, подскажите пожалуйста как стоят шарики и пружинки в каналах. Начал свой разбирать и мне кажется что-то потерял
@DorelBorlea3 ай бұрын
Существует несколько моделей домкратов. У одних система закрытия с шариком и пружиной, у других - своеобразный поршень с цилиндрической прокладкой, у третьих - конический поршень с пружиной.
@ninoratakingofspam582811 ай бұрын
Gracias a su video no use la pulidora para sacar el
@emmanuelbarnay10224 жыл бұрын
Hello I bought the same hydraulic jack 2 tons in France 25 years ago. I don't know who the manufacturer is. I am looking to replace the wiper seal on the small control rod located on the left of the block. Can you tell me about the manufacturer? Translation by google Thank you
@DorelBorlea4 жыл бұрын
328.1200 is the model of this hydraulic jack. Search on google about that number and you will find info
@reginaldopaulasilvasilva19532 жыл бұрын
Boa noite! Tenho um macaco desse aí e fui meche nele porque não estava levantando direito aí fui tirar esses dois parafuzos que tem em cima dele ai saiu mas molas e uma esfera grande u uma pequena e não sei a posição delas vc pode me ajudar?
@Qspecialman4 жыл бұрын
I have the same jack, any idea where I can buy a kit please to rebuild the seals plus the conical spring they got away?
@negakevin83364 жыл бұрын
Nomas tu sabes lo que estas haciendo se supone que debes de explicar paso a paso no como lo estas pasando bato en csmara rapida que bato tan pen
@DorelBorlea4 жыл бұрын
No tenía la intención de hacer un tutorial sobre cómo reparar este gato hidráulico. Acabo de hacer una restauración. Alguien instaló algunas juntas que no eran parte de ese gato. Y debido a esas juntas, todo el petróleo fluyó.
@antongorrio2 жыл бұрын
Hi ! In which hole goes the two steel pellets and the string?
@eduardonavaq53832 жыл бұрын
Donde consigues los oring???
@SharpObserver1A24 күн бұрын
En amazon, por approximadamente 35 Dolares un juego de empaques, son carisimos y solo usas la mitad de los empaques.
@craigstricklin72974 жыл бұрын
I have this exact Jack I would like to rebuild a cylinder don't have any clue what size it is or where to get the parts can you help?
@DorelBorlea4 жыл бұрын
I can't help you either. I don't know what the dimensions of the cylinder are.
@AntonioMartinez-ww2hm Жыл бұрын
Donde consigo los empaques
@kadekad6864 жыл бұрын
Hello could you tell me what is the brand of the jack I have exactly the same I count the renovated thank you
@DorelBorlea4 жыл бұрын
SEARS Floor Jack
@classics289 Жыл бұрын
How come you didn't paint the rest of it? It looks pretty weird with primer showing.
@DorelBorlea Жыл бұрын
I thought it looked better this way.
@mohabatkhanmalak11614 жыл бұрын
What make jack is this. It looks like one of the top quality ones that you cannot get nowadays.
@DorelBorlea4 жыл бұрын
I don't know where this jack was made, but it's a pretty good one.
@handymanjim54884 жыл бұрын
Sears craftsman 328 series from the 70s
@DorelBorlea4 жыл бұрын
@@handymanjim5488 thanks!
@theresahoffman84082 жыл бұрын
You didn't replace any o rings on the valving? Just the one on the piston?
@DorelBorlea2 жыл бұрын
I only replaced the main piston o rings. Only those had problems.
@jorgiporgi1105 Жыл бұрын
May you please tell me what is the name and model of the jack? And the ton rating? Just asking I’m gathering it’s the swivel cog at 4:45 in your vid would you put Teflon tape around the bolt when reinstalled? Thank you. I’m all the way in Australia 🇦🇺
@DorelBorlea Жыл бұрын
The jack lifts a maximum of 2 tons, I don't know what this jack is called. Teflon tape is not necessary.
@Mark11n2311 ай бұрын
Hey, I got a problem, and it won't turn. It has rust in it. I did tried with WD-40 but it won't budge. What would you suggest for me to do?
@DorelBorlea11 ай бұрын
Disassemble it and clean the rust.
@Mark11n2311 ай бұрын
@@DorelBorlea YES! I got it and it works .......... thank you... WHOO!
@everardoherrera22034 жыл бұрын
need help my jack got stuck up position... the gear or sprocket shape don't move
@DorelBorlea4 жыл бұрын
In order to move the gear, you must raise the lever in an upright position. Maybe a little petroleum jelly helps.
@kadekad6864 жыл бұрын
Bonjour pourriez-vous me dire quel est la marque du cric j ai exatement le même je compte le rénové merci
@chelseylover12 жыл бұрын
Whats the part number of seal replacement
@AcUaRiUs972 жыл бұрын
Greetings! I have a question, how do you eliminate the oil leak from the pumping rod?
@DorelBorlea2 жыл бұрын
Hello. The seals on the pump rod must be replaced.
@armandocallizaya15403 жыл бұрын
Escribo de Bolivia, como puedo adquirir retenes para gato hidráulico y donde ? Por favor respuesta, y gracias.
@DorelBorlea3 жыл бұрын
Hola. Tienes que buscar en Google sellos hidráulicos. Vea qué juntas están defectuosas en el gato, mida y ordene desde allí.
@edwinsoto2042 жыл бұрын
de cuatas tonelada es y como consigo el kit
@gustavomazcorro74214 жыл бұрын
Mi gato no levanta es un gato patin de 2 toneladas, ya lo cargué de aceite y no levanta, si no levanta como lo purgó
@DorelBorlea4 жыл бұрын
Antes de poner aceite, ¿recogerlo? ¿Dónde pusiste el aceite en el gato? ¿Cuál crees que sería el problema de no criar? ¿Qué trataste de hacerles?
@gustavomazcorro74214 жыл бұрын
@@DorelBorlea no te entiendo tu respuestas, si le cargué el aceite pues es en el depósito
@gustavomazcorro74214 жыл бұрын
@@DorelBorlea no te entiendo tu respuesta el aceite se lo puse en el depósito quitandole el tapón de plastico
@DorelBorlea4 жыл бұрын
@@gustavomazcorro7421 Usa el traductor de Google. No entiendo español. Es muy difícil para mí explicarlo. Hay varios defectos posibles. La junta está rota, la válvula está obstruida. Mire un video y vea cuáles son los componentes del gato. Intenta comprender el principio de funcionamiento.
@gustavomazcorro74214 жыл бұрын
Pues claro que le quite el papon de plástico si no en donde le pondria el aceite
@m.anasalmasry49284 жыл бұрын
Mantap
@bonifaciojose6742 жыл бұрын
What is the part number kit for this jack? Please..
@michaelb82492 жыл бұрын
Any sizes for the replacement o-rings? I'm particularly interested in the nylon washer inside the pump shaft that sits below an o-ring (size 208).
@hishamchohan4942 жыл бұрын
Well it must be a 45°degree cut nylon ring
@cesarvaldiviezo17904 жыл бұрын
Cuando quite los opresores
@ferforge76642 жыл бұрын
J'ai le même modèle je trouve pas les joints Spy hydrologique 😭
@ouahchiamor7627 Жыл бұрын
Hello, specification of oil please
@kadekad6864 жыл бұрын
Bonjour j ai exactement le même cric ou pourrais je trouver les pièces d Etacher merci
@DorelBorlea4 жыл бұрын
Pour réparer un tel cric. Vous n'avez pas besoin de changer tous les joints. Seulement ceux qui ont des problèmes. Achetez une boîte avec des joints toriques en caoutchouc et remplacez ceux cassés. yato.com/products/11/YT-06877
@kadekad6864 жыл бұрын
@@DorelBorlea merci mais j ai commandé des joints j attend de les recevoir s
@robertmoyer23114 жыл бұрын
Ok so I made the mistake of taking the Allen head plug out. A steel ball fell out, put back in, but jack won't work. Am I missing something?
@DorelBorlea4 жыл бұрын
Search for a sketch of the jack. Maybe a washer or a spring missing there.
@notajp3 жыл бұрын
Check to see if a second ball might have fallen out too. Usually you will have a small ball bearing on the bottom with a larger ball on top. There may be a spring too. On my jack like this, there is a small ball at the bottom, a larger one above it, and a tapered spring on top under the plug. Narrow end of the spring down on the large ball. Not all jacks are the same tho. Those balls are check valves for the pump. One for in, one for out.
@robertmoyer23113 жыл бұрын
@@notajp thanks for the reply, that's exactly what happened. Found the little ball in the driveway. Jack working good again.
@GlynRobinson4 жыл бұрын
Wish you’d do the one I have just like that one. Lol
@DorelBorlea4 жыл бұрын
:)
@adamorossi43332 жыл бұрын
Salve ti scrivo per la scava patate hai seguito un disegno oppure hai fatto di idea tua. Vorrei provare a costruirla grazie saluti
@DorelBorlea2 жыл бұрын
Salve, non avevo uno schizzo per la costruzione della raccogli patate. Ho visto questa macchina e mi è piaciuto come funziona e ho deciso di costruirne una da solo. Per utilizzare una raccogli patate hai bisogno di un piccolo trattore o di un coltivatore.
@marianopacheco88884 жыл бұрын
because it could be that my cat like the one in the video doesn't go up?
@edwinsoto35602 жыл бұрын
De cuanta tonelada es y el número de id
@user-hr6gl1kr9z8 ай бұрын
ราคาเท่าไหร่ครับ
@rambeza Жыл бұрын
А у меня при разборке выпал крошечный шарик и какая то подставочка под него.
@MiguelSanchez-vr1vp2 жыл бұрын
agan vien sus videos
@user-vw3ip8uj1k4 ай бұрын
Идиотский ролик мужик сразу чистит домкрат а потом его красит . И это всё? Гениально!!!
@backtonatureitis2 жыл бұрын
Buna ziua domnul @Dorel Borlea Am un cric foarte asemanator cu cel din videoclipul dvs pe care vreau sa-l restaurez. Imi puteti spune va rog de unde ati cumparat garniturile pentru el si cate tone are? Sanatate
@DorelBorlea2 жыл бұрын
Salut. Cricul ridica 2 tone. Garnituri se gasesc la magazinele cu piese pentru tractor.
@backtonatureitis2 жыл бұрын
@@DorelBorlea Cat ulei hidraulic intra intr-un cric de 2-3 tone? P.S am gasit sa cumpar garnituri la dimensiune de pe internet. Te salut!
@DorelBorlea2 жыл бұрын
@@backtonatureitis in jur de 200 grame.
@truthwillsetyoufree85 Жыл бұрын
The paint job is bad but otherwise good job.
@alanymc14683 жыл бұрын
Lokasi mana bengkel nya
@cesar.arambulacardenas66924 жыл бұрын
Atte César Cárdenas de Guadalajara mex
@user-hr6gl1kr9z8 ай бұрын
อยากรู้ราคาที่แน่ชัดครับ
@DorelBorlea7 ай бұрын
มันไม่ได้ขาย ฉันปรับสภาพแจ็คเพื่อตัวเอง
@nihalakula37613 жыл бұрын
I want to restore my Jack
@ferdinandcalixton1559 Жыл бұрын
Hm labor materials pag nag restore ng ganito?
@ferdinandcalixton1559 Жыл бұрын
Hm does it cost? For restoration
@urbexd44792 жыл бұрын
Cant get my one working
@DorelBorlea2 жыл бұрын
It is necessary to disassemble and see what the problems are. Maybe a gasket is broken or the valves are clogged with dirt.
@urbexd44792 жыл бұрын
@@DorelBorlea do u have Instagram
@markarmstrong33944 жыл бұрын
At 4:44 what is that part called ? I have a Jet floor jack and that stripped and the gear just keeps turning. Thank you
@MrSamBowers4 жыл бұрын
Get rid of the crappy music and just explain what the hell you are doing step by step.
@DorelBorlea4 жыл бұрын
This jack had oil leaks and for that reason it did not work well. Someone put some extra rubber seals and besides these the oil flowed (min 4:20 in this video). I threw those seals and assembled the jack. Now it works perfectly.
@MrSamBowers Жыл бұрын
@@DorelBorlea You didn't show how you did anything. I wanted to see how you extracted the pump plunger seal and installed a new one. This video is a waste of my time. If you're gonna post a video about floor jack restoration then show people how you did it. You didn't.
@DorelBorlea Жыл бұрын
@@MrSamBowers ok.
@roniiisf_28 Жыл бұрын
Shopee COD
@bonifaciojose6742 жыл бұрын
What is the part number for this jack?
@DorelBorlea2 жыл бұрын
I don't know
@radughelase16442 ай бұрын
cum te pot gasi? Am un cric hidraulic la care as dori acelasi lucru.
@DorelBorlea2 ай бұрын
Salut. Am reconditionat cricul pentru mine. Nu am timp sa ma ocup de alte reconditionari. ;)
@radughelase16442 ай бұрын
@@DorelBorlea îmi poți recomanda pe cineva care să lucreze ok? Lucrarea ta îmi place, am urmărit video cu interes
@DorelBorlea2 ай бұрын
@@radughelase1644 doar daca incerci sa il reconditionezi singur. Ca nu stiu daca se merita sa platesti pe cineva
@al3xoradea4 жыл бұрын
Buna Poti sa imi zici si mie te rog ce tip de ulei ai folosit la umplere mai exact producatorul si ce specificatii are Multumesc anticipat PS: Un video foarte ok MESERIAS :D
@DorelBorlea4 жыл бұрын
Am folosit ulei hidraulic. Pentru tractoare.
@al3xoradea4 жыл бұрын
@@DorelBorlea ok mersi
@hapciu3d1232 жыл бұрын
salutare.. cu tot respectul unde pot gasi garnituri sau oringuri pt un cric de 2 tone ?
@DorelBorlea2 жыл бұрын
Salut. Depinde ce fel de garnituri trebuie la cricul respectiv. Poti sa gasesti la magazinele cu piese auto sau online. Masori dimensiunile garniturilor si comanzi online.