Tap to unmute

Double BTS7960B H bridge wiper motor servo

  Рет қаралды 28,294

509trails

509trails

Күн бұрын

Пікірлер: 105
@kevinknowlton5460
@kevinknowlton5460 Ай бұрын
You have no idea how much you have advanced my control and have advanced the knowledge that I needed to put some of this big equipment that I’ve built to use now by emote control !! It’s taking me 40 years to get save and no be able to until this video you put on here changed all that for me !! No words but a BIG fucking thank you !!
@509trails
@509trails Ай бұрын
@@kevinknowlton5460 you are most certainly welcome I'm happy to help
@charleyboy74
@charleyboy74 8 ай бұрын
Thanks for this, it's still helping after 4 years lol
@509trails
@509trails 8 ай бұрын
You're welcome I'm happy to help
@GreyDuck95
@GreyDuck95 Жыл бұрын
Thanks heaps! Been looking for a few days on/off trying to find how to wire it up! It worked great for me thank again!! 😁😁
@tonyfromcali81
@tonyfromcali81 Жыл бұрын
Thank You Very Much for Sharing This Information this will help me on My Next Project
@509trails
@509trails Ай бұрын
I hope it goes well
@22Tech
@22Tech 4 жыл бұрын
thank you! this is very helpful, just bought bought this controller and planning on remote controlling a go kart
@509trails
@509trails 4 жыл бұрын
Your welcome here is a better video kzbin.info/www/bejne/qGPRhnSGi9J7e9k I hope you make a video about your go kart I would like to see it
@murraymadness4674
@murraymadness4674 Жыл бұрын
That is pretty clever to use the servo motor power wires to control the bts
@kevinknowlton5460
@kevinknowlton5460 2 жыл бұрын
Hey 509 have you had any troubles with this BTS7960 loosing reverse or I mean loosing the ability to go one way she bit the other ? I have a ton of these things that have lost the one way but will work in the opposite direction ?!
@509trails
@509trails Ай бұрын
I ran into that problem before and I just replaced the h- Bridge it could be the servo motor too
@RizaOriga
@RizaOriga 4 жыл бұрын
(vcc +) (gnd -)> receiver, I ask if the receiver uses a lipo battery or only uses a 12v battery?
@509trails
@509trails 4 жыл бұрын
The receiver should have its own power 6 volts. I wouldn't go higher than 7.4 or it will burn it up
@RizaOriga
@RizaOriga 4 жыл бұрын
so how to connect the receiver? pin vcc + ground on ibts?
@509trails
@509trails 4 жыл бұрын
@@RizaOriga kzbin.info/www/bejne/qGPRhnSGi9J7e9k The receiver hooks to pins 1 and 2 but you need a servo or a low voltage esc
@509trails
@509trails 4 жыл бұрын
@@RizaOriga what are you building?
@RizaOriga
@RizaOriga 4 жыл бұрын
Thank bro
@dgb5820
@dgb5820 4 жыл бұрын
Great job I’m getting one, so now I’ll use bread for toasting from now on
@509trails
@509trails 4 жыл бұрын
Hahaha that's funny.
@509trails
@509trails 4 жыл бұрын
Here is a more updated video
@UlfBartsch
@UlfBartsch 5 жыл бұрын
Thanks for the video! I started an attempt to operate exactly these wiper motors with the BTS7960. The wiper motor gets exceptionally hot. Is that normal?
@509trails
@509trails 5 жыл бұрын
They should get warm but not too hot you could have a short in the h bridge or the motor try a different motor and see if it still gets hot if it does I would think it is the h bridge. How many volts are you using to the H bridge
@maverick7969
@maverick7969 5 жыл бұрын
So how many volts do you supply to pins 7&8? I understand all but that.
@509trails
@509trails 5 жыл бұрын
I was using 7.4 volts 6v is enough
@robpetrucci3434
@robpetrucci3434 4 жыл бұрын
Fantastic video! I bought 1 of these 2 years ago and could not make it work. However, I'm not sure if I have a different H bride than yours, mine looks identical to your one. I connected it the same way as you did, but it didn't work until I start to disconnect some of the wires and it now works! On my H bridge is connected pins 1 and 2 to the servo (same as your set up) but pins VCC, R_EN and L_EN connected together and that was it. I didn't need to supply any power to VCC GND or any other pins. I'm happy now that my one works, but I'd be interested if someone could explain what's going on with my one? EDIT I've just seen your other video, you did the same thing.
@509trails
@509trails 4 жыл бұрын
Sometime they come dead/ not working here is a more updated video kzbin.info/www/bejne/qGPRhnSGi9J7e9k I have bought so many of these things it not funny some didnt work at all and others just smoked and popped. Thank you for watching and commenting
@muratdal8516
@muratdal8516 3 жыл бұрын
@@509trails bu videonuzu da izledim ve bu videonuzda karta voltaj yine 7 voltmu
@mountaindewdude76
@mountaindewdude76 5 жыл бұрын
I'm wondering if maybe you could help me out. "I am pretty sure" that I have my wires connected just like you do but the motor continues to spin in one direction, or the other, when the servo arm gets moved in either direction. There doesn't seem to be any "end point" in the servo travel. Thankfully, I didn't have the servo arm screw in the servo arm because the motor arm ripped the servo arm off the servo and continued to spin around, ha ha ha. Would you have any thoughts on what I might be missing?
@509trails
@509trails 5 жыл бұрын
It sounds like the stop in the top part of the servo is broken. Or the potentiometer is failing
@mountaindewdude76
@mountaindewdude76 5 жыл бұрын
@@509trails Thank you for your reply! Since sending you my earlier message, I've been messing around with it and I've decided to try a different servo. It's odd because I just had this same servo in a flying wing just last week. I sold the wing and kept the electronics so, to my knowledge, the servo was good. But...I do have other servos around that I can try. I'll try that and see what happens.
@mountaindewdude76
@mountaindewdude76 5 жыл бұрын
@@509trails I see that you just sub'd to my channel. That's cool! I've been flying rc's for about 8 years or so and I've just taken on a desire to build an rc rover, hence the reason for me watching your video. I hope to have something to show soon!!!
@509trails
@509trails 5 жыл бұрын
@@mountaindewdude76 that pretty cool good luck with your build. You can fly 100 times better than I can lol. I think my next rc project will be a tank or bulldozer.
@mountaindewdude76
@mountaindewdude76 5 жыл бұрын
@@509trails I really enjoy flying planes, helicopters, and multirotors....its time for a ground vehicle
@EnergySeeker
@EnergySeeker 3 жыл бұрын
nice video so why we need to put the R and L EN to be HIGH , if i want only to do forward from arduino
@509trails
@509trails 3 жыл бұрын
Thank you. Honestly I'm not sure I would guess just hook up the r then again not sure I haven't used these in about a year or so. If you just wanted forward you could disable the reverse function on your transmitter depending on which one you are using. Sorry I'm not much help
@EnergySeeker
@EnergySeeker 3 жыл бұрын
@@509trails its ok i understand now its just to enable both we need to put both High thanks
@JosueOliveira-yc6hg
@JosueOliveira-yc6hg 4 жыл бұрын
Friend I have a problem! I turned everything on correctly but the motor keeps spinning and breaks the arm that connects the motor to the potentiometer! Do you know how to solve it?
@509trails
@509trails 4 жыл бұрын
Did you take the gears out of the servo? If you did put them back in and test the servo and see it it works right. Also take the top of your servo off and look at the arm stops if it has any. Your potentiometer might be bad.
@JosueOliveira-yc6hg
@JosueOliveira-yc6hg 4 жыл бұрын
I removed all the gears from the engine! I left only the ones in the pot but tomorrow I will use a new deer and give you a return. thank you so much
@509trails
@509trails 4 жыл бұрын
@@JosueOliveira-yc6hg i leave all the gears in mine it helps a lot With the centering
@JosueOliveira-yc6hg
@JosueOliveira-yc6hg 4 жыл бұрын
ok i will do exactly like yours! Thanks for answering me! I'm from Brazil
@509trails
@509trails 4 жыл бұрын
@@JosueOliveira-yc6hg you're welcome. What are you making?
@edwinlaing9834
@edwinlaing9834 5 жыл бұрын
Thanks for explaining the ibt-2 pinout!! Im doing this to run a power wheels steering . But why your wiper motor is over turning? Moves out if the servo steering range.. your linkage looks a little off i think they need to be same leght from pivot
@509trails
@509trails 5 жыл бұрын
You're welcome this was just a mock up how too video it will be much better when I start building my project
@edwinlaing9834
@edwinlaing9834 5 жыл бұрын
509trails i understand .. thanks alot. What is the battery voltage for vcc and 3 and 4 spliced together?
@509trails
@509trails 5 жыл бұрын
@@edwinlaing9834 I use 7.4v lipo
@neuburnrcs2239
@neuburnrcs2239 5 жыл бұрын
Interesting Vids Bruh..soon as I can get a chance to catch up I'm on them👊🏽👊🏽💯👈🏽😎. Keep doing what you doing Brother😁✊🏽
@509trails
@509trails 5 жыл бұрын
Thanks I will lol I can't wait to start on my new project
@MichaelRHead-zv2zf
@MichaelRHead-zv2zf 3 жыл бұрын
do you think it would be possible with the drok XY-1260 60amp controller? im trying to control my gmc sierras quadrasteer rear steering manually. Iwill donate if you can help me out
@509trails
@509trails 3 жыл бұрын
I think it would work. Did your sensor go out? I wouldn't recommend it for on road use just off road use only
@MichaelRHead-zv2zf
@MichaelRHead-zv2zf 3 жыл бұрын
@@509trails Ha yeah the sensor went out. right now im using a rc 150amp esc to controller the brushless motor but it doesn't work as a servo just forward and reverses which works ok. when i drive i just use the rc controller to steer the rear of the truck. it's pretty fun to crab steer. i don't have a clue how to convert the brushless motor into a servo so i was going to just change the whole motor out to a brushed but i needed something with more amps
@509trails
@509trails 3 жыл бұрын
@@MichaelRHead-zv2zf I'm not 100% sure but you might be able to use just 2 wires from that motor. It's a way different application but I was able to use 2 wires from a wheel chair motor. Honestly I would look into hydraulic rear steer. You would be able to install button stops. I'd you used the set like I have on here you would be in the same boat in a week or 2
@509trails
@509trails 3 жыл бұрын
@@MichaelRHead-zv2zf you could buy a scooter/ go kart brushless speed control from eBay the has a reverse switch. That would have the voltage and the amps you need. There are some other BLDC controller boards I don't know how many amps you need
@ganeshpingle.8423
@ganeshpingle.8423 Жыл бұрын
hello sir. amazing video. thank toy for sharing knowlage. i am trying to make 775 DC servo moter using Arduino , moter driver and 775 DC moter but i fail many time. can you please guide me to making this. please Help..
@509trails
@509trails Ай бұрын
I can do my best
@kevinknowlton5460
@kevinknowlton5460 2 ай бұрын
Do you get back to anybody on this channel or have I been singled out ?!?!?! 😢
@509trails
@509trails Ай бұрын
Sorry I don't get notifications anymore so it's hard to respond to people I'm not on here a lot
@skmkh6964
@skmkh6964 3 жыл бұрын
I make it but wiper motor it very hot what happen ?
@509trails
@509trails 3 жыл бұрын
I'm not sure why it would get hot. Try a different wiper motor
@JosueOliveira-yc6hg
@JosueOliveira-yc6hg 4 жыл бұрын
Amigo estou com um problema ! Liguei tudo correto mas o motor fica girando e rompe o braço que liga o motor no potenciometro! Sabe como resolver ?
@muratdal8516
@muratdal8516 3 жыл бұрын
Hocam merhabalar tbi2 modülden aldım 24 v giriş veriyorum ama çıkış 19v alıyorum acaba nedendir 775 motor için kullanacaktır düşük kaldi
@509trails
@509trails 3 жыл бұрын
kötü biri olabilirsin. 36 volt koymayı deneyin ve daha fazla voltaj alıp almadığınızı görün
@muratdal8516
@muratdal8516 3 жыл бұрын
@@509trails giriş 27 v destekliyor diyor ama
@509trails
@509trails 3 жыл бұрын
@@muratdal8516 benim kullandığımın aynısını mı kullanıyorsun Kurulumu görmem için bir video çeker misin?
@muratdal8516
@muratdal8516 3 жыл бұрын
@@509trails tabiki çeker size atarım bir sorucam pin 7 neden voltaj veriyorsunuz ve karta kaç volt ile besliyorsunuz
@509trails
@509trails 3 жыл бұрын
@@muratdal8516 evet
@R3cHin13
@R3cHin13 4 жыл бұрын
Hi , I try to wire 24v motor with 24v power to this h bridge same as in your video , but it runs 2 time short and stop....motor and servo it's ok but h bridge ? How to find out?
@509trails
@509trails 4 жыл бұрын
Try taking the battery pack off of pin 7 and 8. Then hook up pin 7 to 3 and 4. Here is a video with out the battery pack kzbin.info/www/bejne/qGPRhnSGi9J7e9k
@R3cHin13
@R3cHin13 4 жыл бұрын
@@509trails found my mistake , battery have 28.8 v , now I am using 21.6v and I want to start a 24v motor and controll it like an ESC , but the servo potentiometer can't stay at 0 . Ideeas?
@509trails
@509trails 4 жыл бұрын
@@R3cHin13 if you take the servo apart and use hot glue to make the pot stay at 0. Then it will work like an esc.
@R3cHin13
@R3cHin13 4 жыл бұрын
@@509trails stable for the moment , so why all 3 red wires in previous video just works disconnected from the battery , what use they have ?
@509trails
@509trails 4 жыл бұрын
@@R3cHin13 honestly i have no idea. I learned how to hook it up with the battery pack first. And the h brige was over heating and would stop working. I found out it would work with out the battery by accident when it fell off of my lawnmower and it was still working. After that I stopped putting the battery on it and it seems to work alot better
@nizamismailpaklong3533
@nizamismailpaklong3533 5 жыл бұрын
Hi..can i ask you one quection, if i make a rc big car if can i do not use esc like you..tq
@509trails
@509trails 5 жыл бұрын
How big? How many volts.. my esc is an old servo with out the top cover and gears.
@hailtothekingbaby100
@hailtothekingbaby100 3 жыл бұрын
The 298 can only handle a max of 2 amps I made the mistake of buying that one too at first lol
@24242424h
@24242424h 5 жыл бұрын
I finally did it bro, just took a while to understand the concept of servo shaft being the potentiometer lol
@509trails
@509trails 5 жыл бұрын
Awesome its automatic return to home lol that how I look at it. What are you going to put your big servo in???
@24242424h
@24242424h 5 жыл бұрын
@@509trails i used the mini servo, i think it will do the job on our rc steering.
@509trails
@509trails 5 жыл бұрын
@@24242424h I'm using the 1/10 traxxas servo. Now I need to get 2 more wiper motors and set up steering.
@RizaOriga
@RizaOriga 4 жыл бұрын
(vcc +) (gnd -)> penerima, saya bertanya apakah penerima menggunakan baterai lipo atau hanya menggunakan baterai 12 v?
@24242424h
@24242424h 5 жыл бұрын
bro why is my motor always spinning? i can steer left and right but the motor is continuously spinning. shouldn't it be when i turned on all supply the motor should be off and it will only on and steer when i left and right the joystick?
@509trails
@509trails 5 жыл бұрын
Sounds like you have a bad potentiometer try using a different servo
@24242424h
@24242424h 5 жыл бұрын
@@509trails ok i'll try, i just bought it and i tested it before with the controller and it works fine, i don't know if it messed up when I remove the servo motor. btw bro, what's the purpose of linking the the wipers shaft to the servo shaft?
@509trails
@509trails 5 жыл бұрын
@@24242424h I was having that problem to when I removed the servo motor. Now I just leave them in
@24242424h
@24242424h 5 жыл бұрын
I just tested the servo and it's indeed the faulty one, it just spins continuously, btw, what's the purpose of attaching the wiper's shaft to the servo shaft?
@509trails
@509trails 5 жыл бұрын
@@24242424h when you hook the servo horn up to the shaft of the wiper motor it will put wiper motor arm exactly back on Pointe just like the RC servo
@garajfikirleriSK
@garajfikirleriSK 3 жыл бұрын
Bunun nasıl yapıldığını kanalımda anlattım. 👍
Turning Car wiper motor into servo using BTS7960 Motor drive
5:11
Nyagado Morris
Рет қаралды 14 М.
HOW TO MAKE WIPER MOTOR SERVO, BIG SCALE RC STEERING
5:03
RCHobbyFinland
Рет қаралды 23 М.
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
So Cute 🥰 who is better?
00:15
dednahype
Рет қаралды 19 МЛН
Amazing Hydraulic Press!! Powerful DIY Hydraulic Press!!
15:51
KEVGEN MASTER
Рет қаралды 39 М.
How To Use This High Current Motor Driver | HW-039 or BTS7960B Motor Driver
10:31
homemade rc bulldozer at work
5:00
509trails
Рет қаралды 105
DIY Wiper Motor Servo
2:28
kustomkb
Рет қаралды 20 М.
Making coffee from scratch (is hard)
38:34
NileBlue
Рет қаралды 1,9 МЛН
How to Make an R/C Servo from a Wiper Motor | James Bruton
15:31
James Bruton
Рет қаралды 150 М.
Wiper motor servo
5:36
Rotec Aerosport
Рет қаралды 11 М.
Сестра обхитрила!
00:17
Victoria Portfolio
Рет қаралды 958 М.