Double click problem: How to fix faulty mouse button

[@NiLi_]

took me 3 tries just to click on the like button, definitely gonna give this a go

[@Wudanty]

took me 7 to upvote your comment

[@Xoviec]

@@Wudanty took me 1 using another button binded as lmb because lmb doesn't work

[@TheJaniable]

just imagine how many likes this video could have..

[@spookymulder1171]

hahahahha exactly my issue right now.

[@alekdanser]

I liked your comment but it got canceled due to the double click issue

[@arken1814]

Thanks for the guide, i underestimated how small these switches really are, but it really wasnt that bad in the end. Dont know if i bend the copper part too much or not enough (really saw no difference there), but it feels better. fixed the double click and it responds better than out of the box. 10/10, would void warranty again

[@nikoleshlizinger5506]

Yes and do you feell you go to toilet much easier like button

[@IxodesPersulcatus]

Oh. My. God. Performing surgery on cats was WAY easier.

[@dwayne8964]

Thats because cats doesnt have that little copper plate hahaha

[@VERTYSAN]

i buy HUANO ali.pub/0dtmu

[@richardnixon8678]

double click for you

[@RobotronSage]

that is actually very alarming. I don't think you should be performing surgery on cats if you think this was hard.

[@billaa49]

I don't know how I didn't break the mouse in the process haha, well at least it was already broken :P

[@mohammadal-ghamdi3053]

I will do it tonight, please pray for my mouse

[@iommi1337]

we need the results mate )

[@MazzMasserati]

Yes, how did it go? Did the mouse survive?

[@MasterBaetiong]

How'd it go?

[@notanindianscammer3660]

@@MasterBaetiong but the mouse in a trap carefully it can still bit you then hold its head from the back side and do what you should but it still can run away

[@MasterBaetiong]

@@notanindianscammer3660 LMAO

[@OolongChai]

Thank you for the guide but WARNING for others trying this...use a plastic warp cover on top first...because than I open the 2nd latch the top and the white piece fly off the the Galaxy far far away!

[@Ealsonspite]

Should have heeded your warning, lol. It did fly off but luckily my keyboard was in the way to stop it hehehe.

[@Loytuho]

It flew righy on my leg. I was lucky as fuck

[@rsuslik]

I lost the button of my mouse and now my Roccat Kone+ can not be used anymore ;(

[@khalilamiruddin9286]

It flew onto my floor at night and had to use a uv light to find it, the uv light made it stand out luckily

[@smokeywings6875]

I also lost that white one and thankfully found it 😂

[@144ky8]

I solved my problem after watching this video a while ago, I came back here just to thank you. Thanks.

[@KingBobXVI]

I tried to upvote your comment, but it double clicked :(

[@unwokesnake]

i raged a few times, because the copper spring didnt want stay where it should, but finally.. no unwanted doubleclicks anymore :-)

[@alucardwingates447]

mee too hehe

[@romaroalte2645]

Meanwhile I came back to fix this sh*t mouse again, Logitech G Pro Hero

[@xtlm]

It's amazing that they use such a flimsy part on the most important feature of the mouse

[@cattysplat]

It's called cost cutting and it's everywhere in tech at the moment. They rather spent .50 on a switch than $1.

[@hallo-mt5tx]

planned obsolescence, if they made mice that held for ever their costumers would disappear

[@Bisqwit]

Successfully repaired my mouse with these instructions! And yes, the little white piece flied off, but I managed to find it. I did not desolder the button. I used a tiny scalpel knife to wedge the black plastic open.

[@readingsteiner6061]

I'm happy to see you here! Love your channel.

[@KunalVaidya]

Thanks for your message about the little piece flying off, I opened the first switch normally and it flew off, but due to you I opened the mouse in an enclosure so it didn't fly and get lost. the second switch I removed upside down, that is much safer way to removed the top cover

[@alejandroolmoslira7657]

I just finished removing that part and I used Scotch Magic Tape: before unlocking the latches, I cut a small piece of tape and placed it on top of the whole upper face of the switch (I used the magic one cause it is easier to tell when it's not making contact with the surfaces, and it's the only one I have lol, I guess any type would work, but be sure it leaves no residue) so when I was sure it was all secured, I proceeded with the latches and I was able to take it off without rotating it down (my mouse is a Logitec M570, so it would have been quite difficult to do it facing down without removing the whole board from the base and without braking anything...)

[@blabla1177-r7u]

I read your comment first and then went on to disassembly, thinking...I'll be careful. It flied off like a rocket. But found it. :D.

[@lakdav]

If only that copper piece had like 2 nanometers more at that one point so that it hooks properly into the other part... But noooOOooo, 30+ years of mouse button innovations didnt think of that. Also why make it durable and/or easy to handle and fix when most would just buy the entire mouse again instead of going through all this? Thanks for this, saved me a lot of money (if not time and nerves :D)

[@Duke49th]

More durable mouse = less profit. Surprised?

[@TheKalippp1]

azért mert ha veszel egy jó egeret 20ezerért, jobban megéri inkább megjavitani igy mig szállitják az új gombokat amit vettél aliexpressen vagy ebay-en 2 dolcsiért közben meg jobb minőségüek mint amik van bennük lol

[@jeffzebert4982]

sad-but-true fact: mouse manufacturers would start RENTING their mice out instead of SELLING them if they were forced to build said mice to last. That's because renting out is the most effective way to make money with a product that's built to last.

[@TheKalippp1]

@@jeffzebert4982 just steal one laaaawl

[@damanginit2680]

i believe they really want people to buy new mouse. omron has been around for awhile. 2 of my mouses now has double clicking issues

[@GrandeMOficial]

2020 here and it works, thanks for the video. 1 - I bended too much, so I couldn't even click anymore, then I unfold a little bit. 2 - The trick to put it back is: First the side with the small pin, then the other side. Both need to be close to the top (or its going to fall). You can see in the video 3:24 that the metal is a little bit tight and curved, because its in the right position. 3 - Gently press the center area until you feel the click. 4 - I highly recommend a tweezer, a lot easier to move the piece. First try did in 30min~, second try in 1min~, not hard to put it back after you get used to. You can actually know if the click is right as soon as you put the plastic box with the green small click back, because you can click manually with you nail and feel if its clicking or not. IF its missing, maybe you bended too much, as I did in the first try. The noise of right click is less louder for some reason but fixed my Razer Deathadder Elite, 2 months of use and got double click/not registering in the right click.

[@revo5124]

THANKS ITS ACTUALLY SO EASYYYY GENIUSSS

[@revo5124]

Thank you so much omgggg

[@revo5124]

You're my hero I hole you're doing fine in 2024

[@paulb8264]

You made getting that spring back on there look way too easy. My fat sausage fingers mangled the thing even with tweesers

[@furkan1503]

ahh :)

[@cunnyman]

Your fat finger? Fuck that. Even my damn small girly fingers can't put that shit back in.

[@IsawUupThere]

I mangled it too. Luckily I was able to salvage an omron switch from a dead mouse to replace. And if you don't have one, you can order them for $1 off ebay. Replacing the switch was easy, but then I spent half an hour with rubbing alcohol and double sided tape to get the teflon gliders back on without kinks.

[@RobotronSage]

maybe you should lay off the fast food, chubby.

[@Stefanderson]

all the sausage fingers!!!!

[@MeatballBagel]

Last ditch effort, tried literally everything before seeing this video. My mouse was doing the double click/no click randomly thing. Gave it a shot, wasn't too bad, and now my naga trinity is working like brand new again. I gotta say thank you. This is a real solution to a real problem.

[@rolen47]

Video makes it look easy... but it isn't. Got it after an hour of futsing about. There's 2 microscopic grooves that the thin metal piece has to slide in to. Finally got it after I used a pair of needlepoint tweezers. Be patient, don't expect to get it back into the grooves as easily as the video did or you'll get frustrated. After putting it together it clicks better than when it was brand new.

[@mark-davidchandler5895]

futsing about... you mean you failed to use the tools used in the video then realized you should have and that's why you couldn't do it?

[@NomenDaemonis]

It's very quick and easy to do with the right tools, in 30 minutes I fixed my both logitech G300s

[@MrBriancheah]

i realised that if you should place/slide the whole thing in, then only slightly depress the middle spring to lower/push into place for the tension, this way is i feel its damn fast.

[@Warkupo]

@@mark-davidchandler5895 Dont be a dick.

[@Turskaify]

You should have a disclaimer that you make it look way easier than it is

[@SphinxKingStone]

For me personally (first time doing it) the only hard part (compared to video) was placing copper thingy back and putting in small plastic thing

[@mazenmohamed-mm3fp]

@@SphinxKingStone yes it took me hour and a half i was soooo annoyed that i ruined my mouse but when i got it back i was so happy but when i tested the mouse it is not as lite as it was but more stronger like i need to push it hard just to click

[@blitzcraig26]

Can't thank you enough! You Sir, have just saved me a lot of money on a new mouse. My G600 was giving me nightmares in game with the double click. I spent over an hour working on it based on your video and it works normal again. Note to all: Fixing your click switches is NOT EASY! This method requires a lot of patience as you will drop bits time and again. That copper strip is extremely delicate and can bend easily, so be careful. To be on the safe side, if your palms sweat when working on your mouse, spray the internals with Isopropyl alcohol. But my God, when your mouse starts working fine again, its a victory in itself..!!!

[@magnuswright5572]

I literally just bought a new G600 because mine was double-clicking. If only I found this video last week!

[@blitzcraig26]

@@C_007 Wow, it’s actually been 4 years. The fix gave my mouse another year of good performance.

[@markwebb7320]

@@blitzcraig26 It´s possible to change the switch, very cheap.

[@Liz4rdMan]

I agree with every word

[@iceman-1987]

Man I discarded my G600 for clicking issues 4 years ago, but I have it somewhere in the house. Me to my G600 : I don't know where you are or how you are, but I will find you, I will fix you!

[@GugartsAnimations]

3:07 This step will take forever so be pacient.

[@YusufPaw]

It took me around 30 minutes, so yep.

[@marcotermine8]

There are 2 little groove in the mid of the metallic piece, you must put the piece of shit in this groove

[@AlexaCroft]

im going on 3 hours and still haven't manged to keep it staying without jump off when i put the cap back on it

[@az-fy3mp]

took me two whole hour for this, but hell yeah! no more need to buy a new mouse every time that shit happened. if i knew this before it'd save me 4 mouses.

[@maximochkaa]

+az96001 www.ielectronicparts.com/shop/electromechanical/switches/2pcs-micro-switch-omron-d2fc-f-7n10m-for-mouse/

[@chozo69]

+Max K with that method you would have to solder not every one can do that

[@Jimmyfresshhtube]

+Max K sweet! thanks!

[@Kataroku]

+chozo echo (W.W.P.P) Nah, you transfer the wire from a brand new switch to your old one. No soldering required. Good for when the wire-bending trick stops working.

[@mya9383]

mice*

[@Vashiro]

Yo, 2019 here. I have a Logitech G600 Mouse and it started double clicking like crazy.. and I thought it was just dust and some sticky things? After watching this video.. I fixed my mouse and now it clicks like if it was just bought and new. It's a brilliant mouse and is still 100% in tact only the double clicking annoyed me. You've saved me 90+ EUR from getting a replacement or a different model. Thank you so much for this! Cheers~

[@leninyoh]

Guys, this video shows the MOST DELICATE and PATIENCE-REQUIRING step in repairing a mouse button. The rest of the steps of opening a mouse can be easy to understand. But this video shows the best trick for getting that stubborn metal strip back in place. Thank you OP!

[@Ark1j]

I'll 2nd that. Very helpful video, just pay Very Close attention to how that flimsy little strip goes back on. This helped me get my Razer D/A tuned back up clicking good again.

[@AdamKk60]

Well i tried to do this with my Deathadder and the little piece of metal cracked and fell of, so RIP

[@ArcherCodeDelta]

it took me a few tries to get it back in correctly. also, when i tried to open the switch, it exploded, took me forever to find that little white piece...

[@manssupar]

Its look so hard.. Maybe ill buy another switch by omron that have more better clicks. Its pretty cheap actually

[@ricgomez1]

How would you know, have you done it before? I hate people that see a video and try to give instructions on something they've never done.

[@christianpetschke592]

+3 years for my mouse since i watched this video for the first time (watched it twice now) ^^

[@Tipichno]

Thanks! My Sensei MLG was a little loose - sometimes double clicking. Now it's clicking better than new. *bow*

[@AspectCave]

ok

[@migs_unit2130]

NOT ALL HEROES WEAR CAPES! THIS MAN JUST PREVENTED ME FROM SPENDING MONEY! Just thought of giving up and buying a new one then I saw your video. Now my mouse works like charm. Thank you so much.

[@jessierabino822]

u still need to buy a new one . its gonna fall again 3 to 5 month maybe thats happend to me this is not forever fix .but its working :D

[@BlackSeraph]

You saved my 80€ gaming mouse from an early grave +PCGamingWiki. Awesome tutorial!

[@TheKingBJ]

"Gaming" mouses are a scam. Mouses are the simplest shitty input devices, it's like buying a screwdriver for 10 times more money expecting it to drive a screw much better

[@baaadger]

Well some gaming mice have programmable buttons, plus they are more comfortable to hold. So no, they aren't scams unless they are WAYYY overpriced.

[@dicksonlickson1024]

you are dumb enough to buy a mouse that is worth 80 euros, ahahaha you are laughable

[@spookz4469]

@@dicksonlickson1024 They have a higher response rate and are faster than any normal mouse, and depending on which one you get are usually MUCH more comfortable, along with programmable buttons. But hey, you're obviously just a troll with nothing better to do with your life, and im pretty sure we can tell that simply based upon your username. Lol.

[@MarcoAntonio-fh5cv]

Funcionou, depois do que fiz o meu mouse está funcionando 100%. Me poupou alguns reais kkkk salve from Brasil! Tks

[@badboiijose1]

i fucked up my mouse.. now it dosnt click at all

[@ETin6666]

+Raven. That's so Raven.

[@badboiijose1]

Yup thats me

[@stefanie_m466]

+Raven. look at the bended copper part , it has 2 dents that should hook on that little thingy .

[@sarveshpavale3930]

+Raven.You might have placed the cover with white little button WRONGLY....CHANGE IT TO 180 DEGREE....as i made this mistake.....

[@TurtleSergio42]

now I'm afraid to try...

[@canelacinzenta]

QUEM TA BOTANDO FÉ QUE ESSA PORRA FUNCIONOU ahahhahahaha Muito obrigado, consegui consertar meu mouse de 25 reais

[@overlost1576]

good tutorial. (fuck that cliking thing. it's so annoying to put it together xD)

[@nicks5759]

+OverLost420 I know exactly how u felt, just done putting mine together ..

[@overlost1576]

XP

[@gaia35]

Fuck that was hard to put back together, i have a razer deathadder chroma, if you have the same mouse, are the clicker buttons smaller, cuz mine seemed really small compared to his XD

[@DeSinc]

why does software even listen to 2 clicks within the space of 0.000000001 micro seconds anyway?? who is going to actually double click that fast? the answer is nobody, nobody clicks that fast

[@DerfK1]

The most important thing is that there is a limit to how far you can bend the curved piece. I just spent 1.5 hours trying to figure this out, but if you bend it too far, the middle spring won't sit on the middle post and the whole thing just falls down. Then you have to straighten it back out so it can reach the middle post. The trick I finally did was to put the contact end in first (the end with the raised dot that fits between the contact and the stopper above it) then used my fingernail to scratch at it to get the opposite end to hook over the post. That got me to the point you see at 3:22. Then, I kept my fingernail on the end to hold the spring in the groove and straight while poking at the middle spring with my tiniest screwdriver STRAIGHT DOWN very carefully. Push too hard and the whole thing falls down and you start over. Fail to keep the end in the notch or push unevenly and the spring will shoot out to the side and you start over.

[@SendNubes96]

thank you

[@julliferjosephtuba2202]

Wished I read this before going at it. Just finished fixing mine a few minutes ago. This would have saved me at least an hour.

[@micmal5836]

Thx, you helped me a ton

[@TheNewton]

Same set the ends then pushed the middle, it's never clear if it's same to hook the two ends then push the middle undercurve part to click because it's so fragile

[@Longs81]

1. Watches video.... 2. Throws mouse in the bin. 3. Buys new mouse.

[@testtwo1580]

Mine don't even click anymore. Also be careful bending that metal part it snaps really easy.

[@cIeetz]

good thing i have 4 of these that dont have usb sticks to practice on

[@fuehwbdb3765]

Hey mine also don't click anymore was it the switch ?

[@rev927]

@@fuehwbdb3765 make sure you push that little plate until it clicks, look at 3:45 / I know it cuz i had the same problem

[@aniketsingh5516]

Same!

[@Hirux]

Now it's even harder to press my Left button lmao

[@filipesilva2624]

the more you push the curved (spring) part, the harder you need to press the buttons, for fixing the "double click" problem you just need to brush the contacts (the bump part) with a rubber/eraser

[@Act1veSp1n]

putting this thing back together is probably the hardest thing...mine fell apart after 10th try

[@luxunited5449]

Same :D But i finaly manged to fix it (now the other half... wish me luck)

[@Verdigo76]

I did this on my G600 for the left click. The fix has lasted for 3 years and counting. It took me 4 hours to get that copper spring back in. Now it's my right click's turn . Sigh. I swear, this is a part that can be made modular. Double click issue? Just snap in a new clicker!

[@ΠασχάληςΜιχόπουλος-β3κ]

ahahaha :D Razor Imperator fuck!!!

[@NJ-wb1cz]

G600 has a slightly retarded construction since the dirt falls right onto the switch. I did this for mine 3 times already, last time I used tape to cover the insides as much as possible. Will see if this helps. Still the best mouse ever without any alternatives. Razers and others suck because they don't have classic 3 button construction. Holding G600 is like using those old pre-scroll Microsoft mice with just huge 3 buttons on top. Except of course G600 does also have a scroll and thumb buttons.

[@Verdigo76]

If you've had to do it 3 times already compared to my 1 then perhaps you should consider bending that copper part a little more than you usually do. I took note of where it was when I opened it and moved it much further than the original spec (because obviously the original spec wasn't good enough) so the fix would last longer. That's coming from someone who uses their computer 12 hours a day or more. Lots of clickly click clicks.

[@fancifulspoon8094]

Pro tip to those that attempt this, the copper piece is annoying AF, and if you don’t keep your cool, you can easily break it. If you bend it wrong while putting it back in(difficult AF) it will be harder to get it back into its spot, because the grooves were seemingly built for specific tension, and you cant bend that copper thing wrong or else it’ll not bend back without risking breaking. Just be patient and keep your cool. It may take a few hours but as long as your gentle, it won’t break, and you’ll eventually win. Edit: I broke two copper tension things, ruining 1 mouse. It was just an old broken test mouse. I had two old broken mouses, I was able to fix the other.

[@julliferjosephtuba2202]

Here to confirm. Opening the mouse up and getting to the copper thing took only about 30 minutes (with youtube tutorials), despite this being my first time disassembling a mouse. Putting back the copper thing took over an hour, and a fraction of my sanity. It flew off my fingers a couple times, and had to spend a few minutes to look for it on the floor everytime. End result: It actually worked. Fixed the double-click as well as the drag-drop issues. *BUT* I might have messed the copper thing up a bit too much, cause now my mouse button doesn't give a distinct 'click' (both sound and haptic). Nevertheless, it's more than enough for me, especially if compared to buying a new mouse entirely. Someday might try swapping the copper thing of my left and right mouse buttons if I never get the used to this silent-mode MB1.

[@kyuzex]

​@@julliferjosephtuba2202 i dont know if im too late, but i attempted this (saw some other video first) and it worked, but i too lost the 'distinct' click. Though I just figured out what i did wrong, at 3:50 they "click" the middle part of the copper thing back into place, which i hadn't done. I just re-opened my mouse and re-did the fix and i now have the distinct click too!

[@roct07]

@@kyuzex bruh you're a savior. Been trying to get that copper piece back into its place for 30m now but the click wasn't there. Thanks!

[@JanKowalski-pv4jn]

A thing to note: what this fixed for me was not a double-clicking problem but mouse clicks not registering, as well as losing your click when dragging and dropping. Difficulty: 7/10, be prepared to burn several hours on this. Depending on the mouse, the screws are under the teflon, which will start scratching your mousepad, sometimes even after a lot of trial and error. The Omron shell is small, and it's challenging to see the crevices without proper lighting, but I did this without unscrewing the whole board with the mouse still plugged in to the PC. A sewing pin works for popping off the cover with some trial and error to find proper leverage. The white plastic piece that puts pressure on the copper tends to bounce away when popping off the cover, so be careful! The copper: slides out, as seen in the video, easier to one side and not the other, so don't accidentally bend it. Once I removed the copper piece, I bent the curvy part backwards with a toothpick, but only to the point that the "claw" was even to the base, in a nice neutral position. Inserting it back in will bend it down somewhat, but my clicks still worked fine afterwards, so I wouldn't worry too much about keeping it "neutral". Obviously, be extremely gentle during this step. Mounting the copper part (the most frustrating step): you will either lose your mind at this point, accidentally break the goddarn copper, or lose it somewhere because it's going to slip away every 10 seconds. Ideally, you're going to want to unscrew the whole board, so the shell doesn't interfere with the leverage. I did not and regretted it because the thing is just that fragile. I don't know if the bottom part of the Omron differs ever so slightly from the one shown in the video, but what is hard to see is that there's a tiny crevice in the prong at the center that's supposed to keep the curvy part in place. So, after an hour of trying to figure out how to put pressure on the copper the way you see it in the video (it has to bend, starting like in the video, and then latch onto the prong at the end, so it stays fixed), I eventually figured it doesn't feel like it's snapping in, doesn't click, nothing, it just sort of stays in place, but will fall off when pushed even slightly to the side -- this is the part that's "clickless" because you haven't snapped the curving part into the crevice. The good thing is doing it like the author of the video is doing will eventually work, but it's more helpful to take the casing off of the other switch to see how the copper is fixed in place -- in the video it doesn't look quite right. The final step is just a lot of trial and error, you have to press down on the thing that has to latch into the crevice in the middle prong, but the copper piece is just too unstable. I tried it with a toothpick and with a screwdriver, but I found it's better to apply pressure at a diagonal angle than downwards, at which point the toothpick eventually worked. Don't put the casing back on unless you can press the copper down with your finger, so you can see it doesn't move around or you might bend it beyond repair. The mouse should click normally if you succeed, but not before you assemble the casing. Putting the shell back on seemed trivial, so I won't go into detail. Hopefully, this is helpful to someone because this was frustrating as hell -- and F**K Chinese Omrons.

[@yamoonie]

i just did this on my logitech g302 that kept double clicking after 9 months. WORKS LIKE A CHARM. also its pretty easy if you have careful hands.

[@iMakeFunWithFish]

Thanks bro fixed my old 70 € worth Mionix mouse which started acting after a few years and I thankfully didn't throw away. And when I will get the torx screwdriwer I'm gonna fix my newer, Corsair M65 too which also started acting up right after the warranty period. I am not even gaming and got expensive gaming mice cause I thought they will last, oh boy was I wrong. And I don't even play games on PC, the most clicking I do is in Photoshop while clonestamping or something. I'm very glad I know now what causes this and how to fix it!

[@reginald56000]

took me 30 minutes to return that Metal piece!! omg!!! Thanks for this though i fixed my mouse now O_O..

[@Adamzenn]

I can kindly say this worked. It's a really easy fix. The only issue I ran into is putting the small copper piece back in place, but otherwise this worked, no complaints. Thanks mate!

[@hacker6695]

same here... finally new mouse

[@PhilyDips]

30 minutes and done! After following your tutorial, the double click issue has been fixed! Saved me some money, since I didn't have to get a new one!

[@gemoplay-7165]

Guys I found a much much clearer video : kzbin.info/www/bejne/fJbTnp2aj6tjmtU please dont get me wrong this video is great and it helped alot but it needed more explanation and better recording angles. And that's what I found in the other video. Thank you both for taking the time and effort to do this ❤❤

[@kellionisthallis6349]

I had the genius idea of trying to do it via pictures, only after I broke the fucking copper plate I checked the video and saw what I did wrong. Bloody hell... -_-

[@Akashsama]

My problem is the little mechanism boxes in my mouse are like the one in the middle @0:12. That one is different and i can't manage to open it :/

[@MrBile07]

+Akash-sama same here,have no idea how to open

[@muhdiboy]

+Akash-sama you have to open it from the brackets on the front and back, the piece that connects the black to the white

[@josemiguelq]

+Akash-sama Same here mate, almost impossible to open it

[@skyworth999]

+muhdiboy the second click box shown is harder to open, its really different from the front/back.

[@skyworth999]

+Akash-sama have you manage to open it? i really need help

[@KingBobXVI]

Finally got around to doing this - managed to get it back in in not _toooo_ much time. Thanks a ton for the video, and showing each step! One small tip: put tape across the top of the internal button before removing its case - this will help hold onto the little white button piece so you don't drop or lose it.

[@jonathanross1395]

Fixed the double, triple click issue on the logitech g900. Thanks for this video!!

[@hgilial3752]

tried this on my g600 and could not get the spring attached again and lost it in the dirt eventually. Took a switch from an older logitech mouse to solder on but ended up melting some stuff off the board and just took a hammer and destroyed it. To sum it up i ended up ruining 3 units instead of reparing one. So if you dont have the right soyboy fingers to mess with this stuff it will be extremely difficult.

[@_thechosen]

Why not ask girlfriend to solder for you?

[@Avrelivs_Gold]

It's easy to ruin electronics, that's why people get paid. If you decide to fix something, always have a backup plan.

[@2Mad4Play]

Thank you for this great tutorial. Fixed my "Roccat Kone Pure" laser mouse. It was a bit tricky to put back the metal plate back in place, but the rest it's easier than it looks. I think everyone is capable to do this at home.

[@Curioust2020]

my man just broke the best drag clicking mice

[@lemurmad]

Wonder what the Roccat Kone EMP is in that league... Was a RIP to the left click till I fixed it from this video.

[@2Mad4Play]

@@lemurmad Look for the switches. Kalih 8.0 are rated at 80M clicks and this is your best bet.

[@newman79]

Thank you for this brilliant tutorial! Beside repairing the loose spring, I have also swapped left and right click springs in their switches for better load balancing. My Logitech MX Laser from 2006 (yes, 15 years, no gaming) is back on daily track.

[@joelconnop7845]

Thanks so much, I was eventually able to fix my Razer Imperator. My tips: Also see his 'full guide' link which gives better detail for the really icky part - getting the spring back in place. Might have saved me an hour if I saw that first! Oh and my little white plastic switch also went flying, it's a miracle I found it. For my mouse, I had just as much trouble getting re-assembling it properly. The right click "didn't work", but I eventually realised that it was in 'always clicked down' position, due to me not screwing the PCB in TIGHTLY (at least a few turns tighter than I would normally screw something). Do a few laps around the PCB with your screwdriver, because when one has gone in further, another that felt tight a moment ago might now have a few extra turns in it.

[@jonathanbreauxpalski1817]

So my dumbass didn't need to order 30 switches from aliexpress and then wait 2 months for the delivery😂

[@MythosTBK]

This was excellent! I saw many other videos concerning this matter and read a dosen more tutorials and drawings but this video was the only one that made me exactly understand what i have to do to fix and reposition the metal plate! Great tutorian man! Keep it up!

[@wardunnnup8651]

did it successfully on my razer deathadder elite. I would play around with it since it's a little harder to press down, but I've ordered a new switch, so it's no biggie. thanks for the tutorial! doubleclicks went from 20% to 0% and took about 10 minutes first attempt.

[@stekarknugen9258]

To anyone getting frustrated getting the spring re-attached: Don't give up! I had the hangover shakes and couldn't find my glasses to see properly but I got it in the end! Basically try to copy his exact methods.

[@sebalutz]

I would wonder if this solution would really help - watch this: kzbin.info/www/bejne/rGalmXh5i9F-gKM The problem is the result of multiple factors like material (alloy), construction, circuit, snap mechanic, voltage level etc. If you run into this problem simply exchange the micro switches against better ones

[@tatsuuuuuu]

PCGamingWiki Dude ... uhhhh.... thank you. From the bottom of my heart, thank you. Your video is perfect. Fixed a Steel Series ikari laser white.

[@vladimir0rus]

I have a much easier way to fix any buttons including the power button of your smartphone. You need to drop a drop of mineral oil on the button contacts. The oil will prevent the formation of an oxide film and the button will function like new. You can use engine oil or any other liquid mineral oil used to lubricate mechanisms. This also works with volume control potentiometers in audio amplifiers.

[@jotaaaajunior]

Fantástico! Vídeo maravilhoso, me ajudou bastante. Thanks! 🇧🇷

[@janithsandaruwan6900]

Oh god I tried this before watch this video..LoL..Trust me Surgery is easier than this..Final part is the hardest one..it is not easy to reset that small white button

[@BobusCM]

It's 2019, and this works just fine with the razer naga trinity. You, my good sir, deserve a medal for this.

[@mikethegamer34]

2022 still works :) now i still need to find a fix for the "Repeat Scroll Down" button, the one you tilt the scroll to the right... sometimes works, sometimes don't... but well... at least my left click is working... lets see for how long

[@aimankamil4818]

​@@mikethegamer34 you just need to oil the bearing, use wd40 or something like that. Work for me

[@ixpert3517]

I just replaced mouse switch today. But, Wow. Easy repair without new part. Thank you.

[@Sk313ton]

Thank you very much!!! You saved me over $40.

[@1pqlamz466]

Fixed the double clicking issue on my g903 seeing ur video, awesome!!!

[@presskeytoplay]

4 hroas e 35 minutos para fazer o processo no LMB e RMB do meu g600 Se fosse comprar botões novos e mandar soldar, acho que ia gastar uns 50/60 Reais 15 reais por hora de trabalho, é, acho que valeu a pena um pouco

[@weapon777]

preciso fazer isso no meu 600... durou 6 anos

[@yellow_cone]

이거 동판 금속 끼울려고 2시간 고생했는데 이렇게 쉽게 끼우는거 보면 허무하네. Oh Shit. . .

[@-_--bp2uc]

People:"My mouse is double clicking" Minecraft Bedwars and PvP players: "oh i wish i have a mouse double clicking like your mouse."

[@janithsandaruwan6900]

And also it worked..Thanks..But now click sound is reduced..

[@markdarylsamera1209]

Hi! Thank you for showing this one. Saved me on buying a new mouse :) Keep it up!

[@TheLonelyViper]

tHANKS!

[@rustyshackleford8022]

There's a really easy way to do this, lace the tapping bit (let's call it front) under its receptacle then pull it so as to hook the other end keeping the curved bit above the center receptacle. Push the back end down so it hooks. You'll then have it fixed in place but it won't click, all you need to do at this point is push down on the curved bit so that it snaps into place (use a toothpick or tiny screwdriver). Took me an hour for the first one until I figured this out and then 30 seconds for the second.

[@themysticbg]

Thank you man. After 2 hours of trying I wanted to perform Seppuku, thanks to you I managed to fix it! I've done this twice (today and one more time two years ago) and my mouse works like new.

[@rustyshackleford8022]

@@zams4517 not sure what you mean the method I describe has worked fine for me. I just buy a few new springs for like 5 bucks (the entire microswitches which I cannibalize) every few years for my g500. If you are just rebending the same one you are going to lose integrity of the metal and corrosion (ie humidity) will reduce contact sensitivity over time as well.

[@rustyshackleford8022]

@@themysticbg Glad I could help I actually figured this out like 6 years ago and then forgot it so I posted the comment to help remind myself as well lol.

[@rustyshackleford8022]

@@zams4517 no worries

[@KunalSaini97]

Instructions not clear. Now the pin is in my stomach

[@wakko3wb]

IT WORKED!!!! Thank you very much.

[@rustycranium8952]

Finally the mystery of my dead mouses is solved. Many thanks!

[@Pertamax7-HD]

super sir

[@english_chat]

I've fixed my mouse, now it became silent on left click :D

[@richefurea]

yeah same , did you managed to fix it after that?

[@thomastrololo1]

@@richefurea loosen the screw under the RMB a bit.

[@shadigif8916]

Disclaimer attempt this difficult repair at your own risk

[@TheElThomaso]

Some important hints: 1. Get tweezers before you attempt this, as it's almost impossible to do with your fingers. 2. When opening up the switches (at 1:34), make sure to do so very carefully, in order not to have the little white part flying away! (very important and has been mentioned by others below) 3. When putting in the metal spring back in (after fixing it), make sure to push its second latch (the left one at 3:21) not all the way down! If you look closely, there's a very fine groove where the metal of the spring has to slide in. If you push it all the way down, the switch won't really work (I did this two times before figuring out the mistake!) Other than this, great tutorial, thanks for the help =D

[@itssamiultahsin]

This really worked man !!💯🔥 Thanks ❤️

[@clicko1231]

You sir ! You are awsome ! I just saved my mouse thanks a lot for showing us how its done !

[@wowdude4377]

Wellp, fucked my mouse even more. Can't get that fucking copper piece to reseat and stay up and supported. It just falls down. Don't know what I did wrong considering I did everything you did but looks like I'm gonna need a new mouse. Again

[@BeatBall]

me too lmao but i feel like i wasted my money on that gaming mouse, my simple 10$ logitech is still holding yet for 2 years

[@flaviocarvalho9076]

You safe my life, man. This is the best tutorial ever made. My Logitech G500 was like new again. No more fu**** double click. Greetings from Brazil!!

[@GordorBR]

Eh isso ai carai, salvei meu Razor tb nesse lance! Cara é bixão mesmo

[@serafinhs491]

Thank you so much for this tutorial. It's quarantine time (Covid-19) so I'm so hapy I was able to fix this.

[@Eagleizer]

Thanks! Works great. I recommend trying to clean the contacts with a thin, sharp blade, and add contact spray and see if that works before taking it apart. It can be difficult to put it back together. If you do take it apart, note that the back end (opposite of the contact) should be mounted almost at the top. Also be careful not to bend too much as it will make the click harder. I also removed the weights while I was at it and ordered 5 switches on eBay for $1.20. The ones you want is: Omron D2FC-F-7N When you solder those switches, use a ~300C tip and do not heat for more than 3 seconds... (factory recommendation) Cheers :)

[@davidesantos9214]

I fixed it on my Roccat Kone Pure Military, but I bend it too much and is a bit harder now, hope that get softer overtime. If that happen again I prefere buying a new switch and lose 30min trying to get that little spring plate on place.

[@oluwaseyea.agunbiade2127]

Don't be fooled, 3:10 to 4:00 alone takes 2hrs in realtime. Almost emptied my savings to get the pricey bluetooth Logitech M557 because my laptop has only 2 USB ports and i didn't want a mouse with a dongle. Imagine my horror when lt-click started acting up after 1 yr. This video actually saved Logitech cos i was about to place a curse on them. But seriously though, why all logitech products?!? Thanks a lot bro!!!

[@anonime395]

they make every electronic device to last a bity more than warranty terms. in most cases 2 years. Sometimes they get unlucky and device breaks 3 moths before not after warranty period and they have to replace device for free.

[@miteshmalgaonkar3569]

best mouse repair tutorial ever

[@MYGRiNboy]

This video is a bit old already but I can't believe they still didn't put a disclaimer that you need high precision fingers to perform this.

[@rahul4024]

The people who are going to benefit most out of this video are Gamers and our gaming mice. And gamers are GoDLiKe(unreal voice) when it comes to precision.

[@hereandnow5235]

worked even with some kitchen utilities and pincer of my girlfriend, saved 89 Euros, thx a lot!!!

[@tofudeliveryman4239]

HOW DOES HE FIT THE SPRING IN SO QUICKLY AUGHHHEHHEHGHHHHH

[@putzi019]

did this for an hour, fixed my logitech g102 prodigy, thanks mate

[@ockysiswanto]

Fixed my g102 with this method also

[@greentonium]

Nice.. sidewinder x5 ! 2009 y.o. :D fix

[@vanshpro]

More easy solution spray wd-40 on those button and it starts to work like new

[@JanKowalski-pv4jn]

Isopropyl alcohol. WD-40 damages plastics and is not designed for contact cleaning.

[@GalaxyBG]

This solved my G300S button click problem, anyway it was very difficult to place the thin copper.

[@JosueHernandez-eh5jo]

just fixed mine as well!

[@RogerToonTime]

I was looking for videos on how to fix my mouse and was gonna try this method but managed to fix mine with a safer way, so if anyone is interested, I recommend trying what I did before trying this: Put some non oil based contact cleaner through the button gap in the switch and click it over and over again, don't close the mouse yet, wait for it to dry and test the mouse, if it didnt work, try a few more times. If it fails it might be a physical problem with the switch so you can then try this method in the video. If it also fails or if you damage your mouse you can buy new switches and solder them to replace them. I got some Omron switches on Ali Express but didnt end up using them cause the cleaner worked for me, you could also take the opportynity to get some other type of switches and mod the mouse. I also got new mouse feet on Ali Express to replace mine in case I damaged them while opening (cause the screws in mine are under the feet). (If you buy on AliExpress keep an eye on the costumer safety guidelines so you can ask for a refund in case your order dont arrive in time, cause buying thins from random sellers from so far is a gamble, Ali Express is actually pretty good with refunds if your product dont arrive or is damaged/fake) Either way, this video explains this method pretty well, I'm glad I didn't have to use it but it was nice knowledge either way, cheers!

[@MrGyamjo]

Who is fixing it in 2020 cause I am xD

[@shake2572]

I did this removing is easy putting it back its like playing dark souls its hard but its fun no more double click yay

[@bruce3906]

i did it, on logitech g203/102, but it too me 2 hours+ lmao

[@trntzx00]

Those damn switches!!! The little copper piece is so hard to put on again

[@Avrelivs_Gold]

there is an important trick 3:30 i did it my own way but it came out too soft

[@deetoxvengeance]

I love you. About to throw my naga trinity in the bin and buy a roccat mouse. Tried your video and voila - naga is reacting like a new mouse. Thank you so much!

[@SevenSixTwo2012]

This is not worth the time and frustration. The metal, once deformed, will no longer retain its springiness in the long term once you bend it back. The only permanent "fix" is to buy a replacement switch, de-solder the old one on the board and solder in the new one.

[@gussi3540]

2020 and I fixed my mouse double clicking with this video. Thank you very much ^_^

[@gussi3540]

@@rafifwiratno a lot of patience, it basically hooks into place

[@rafifwiratno]

I had the same problem as you, but now it's fixed (almost bought a new mouse lol)

[@TechInspected]

It also helps if you clean the spring (the flat metal with a little curved middle) where it touches the contact points.

[@D7l]

it works for me thank you

[@cIeetz]

ok guys I figured out how to put the thing back in easiest. Please like this comment if it helps so ppl can see (precursor) Put the unit up to a wall mounted light source that is eye level so You have light coming in from the back if possible and You can see better. 1. pinch the back part of the piece with two left hand fingers(index and thumb), watch it from a side angle, Slide the front part HALF WAY in between the 2 thin metal pieces(you should know what I mean by front part now) *while* making sure the middle part (the spring part) doesnt fall down to the bottom, push it down with right index finger so its slightly tucked in, but doesnt fall right through 2. keep holding the front part down in place from above with right index finger, now tuck the back part securely in with left thumb 3. now that the back parts in, the front part will naturally be in all the way 4. keep the thing perfectly even, if its slightly sliding sideways, fix it, now use tweezers to push middle spring downward (push down more towards the front part, if you push down towards the back part it will fall through) WHILE holding ur finger on the back part firmly to keep the piece from shooting out this part is tricky as often you will push too hard or on the wrong spot, and the spring will fall down to bottom, slide it out and try again.

[@cIeetz]

this comment will likely save people 45 minutes, nothing worked until I did it like this, now I could do this in 2-3 minutes everytime

[@cIeetz]

also be meticulous when putting the black box cover over it, it could pop the piece off if You arent careful