Drawing Machine Assembly and First Try

Complete Bill of Materials:
3dmake.club/art...
Files and software:
3dmake.club/art...
My build of Drawing Machine by cyul (www.thingiverse...) with some little changes.
Here is an assembly video.
I ordered all the electronic components, rods,bearings, etc on AliExpress
Linear Shafts 8mm*400mm - 2pcs - ali.pub/1xattp
Linear Shafts 8mm*320mm - 2pcs - ali.pub/1xatr6
Linear Shaft 6mm*200mm - 1pcs - ali.pub/1xax78
LM6UU Bearings - 2pcs - ali.pub/1xau1h
LM8UU Bearings - 8 pcs - ali.pub/1xatyr
16 Teeth 5mm Bore Timing Pulleys - 2 pcs - ali.pub/1xavsh
16 Teeth 3mm Bore Idler Pulleys - 1 pcs - ali.pub/1xawbj
No Teeth 16 3mm Bore Idler Pulleys - 4 pcs - ali.pub/1xawbj
GT2 Belt - 2m - ali.pub/1xaudq
Arduino + CNC Shield + A4988 Drivers - 1 pcs - ali.pub/1xaukc
Nema 17 Stepper Motors - 2 pcs - ali.pub/1xath9
28BYJ-48 12V Stepper Motor - 1 pcs - ali.pub/1xaupz
Wiring Kit - 1 pcs - ali.pub/1xauz4
Power Source 12V 4A - 1 pcs - ali.pub/1xav4r
M3 Bolts - ali.pub/1xasl6
M3 Nuts - ali.pub/1xasw2
Buy in local hardware store:
M10*400mm Threaded Rods - 2 pcs
M10 Nuts - 8 pcs
M3*8mm Bolts - 11 pcs
M3*20 Bolts - 10 pcs
M3*30 Bolts - 8 pcs
M3 Nuts - 22 pcs
Inkscape gcode output extenstion for this thing based on MakerBot Unicorn gcode Output Extension: rgho.st/6xLQH5WJv

[@anasrahman4729]

thanks a lot sir for a complete guide about grbl modification. you are only one who tell this. thanks again

[@SuperMaDBrothers]

I'm totally digging the music

[@mohammedebrieeshetie790]

MATHIMATICS I ACTION , THANKYOU FOR SHARING THIS HOME MADE DRAWING MACHINE

[@user-ol3or3hc9y]

My cnc pen plotter is going on the wrong side. When it draws the picture, it is not in this direction, but it is moving to the left side. how to fix it? Is it a software problem?

[@Nomad_Wanderer]

Built the same with just Rs.2500 including all the parts mine was laser cut, rods were salvaged from old printers and the steppers were also from old xerox machines... The acrylic used was 16mm, 10mm & 6mm.. 120kg for acrylic scrap, parts took around 14mins to cut on co2 laser CNC 14mins x Rs. 8 = Rs.112, steppers cost Rs.60 each minebea 1.7amp 1.8deg, cnc shield +arduino uno+pololu stepsticks driver=Rs.1200, linear bearing Rs.600...

[@PrathameshJakka]

make a tutorial

[@mustafamahameed6649]

Khadim Ali where and how I can get it?

[@lucianosantos5036]

Please, could you provide the dxf files? Unfortunatelly, I don't have 3d printer, just a small cnc router.

[@furqanahmed6]

AA . Khadam Ali bhai . I want to see this machine . Can I contact you or can I buy from any place . Plz ? SMS me 03227663131

[@ann-kathrinv3963]

Hey ! Any chance I could get access to your laser cut files ? I wanted to print them first, but I guess printing them with an old ultimaker could be difficult. I would really appreciate your help !(: Thank you!

[@DETUDOUMPOUCO-ne6js]

I've been trying for 6 months now but the servant doesn't I don't know what else to do!!

[@theindia9725]

Sir ,Kindly make vedio on software installation n implementation .

[@mousa65]

Very nice Drawing Machine, I am building one for me. Thank you for sharing.

[@49agastyawagle50]

which software would you use

[@MineOrebaker]

Files and software link doesn't lead to me download link will you please send me the link or directly to me !!

[@vikashkumaryadav1470]

Where I can buy it.

[@karfex]

Hello, the page with the software information does not work, what is the name of the software you use?

[@santoshchaudhary8686]

hello sir when i move x+ it moves diagonally can you help me to solve the issues

[@aadityarane3464]

background music. first I feel like it coming from outside of my house .

[@Electraglide1350]

.............. turn it off ....listen to your own music ... why the bitching ....

[@macacinelecanale]

What the fuck do you have with those who didn't like this shit music?

[@MrNonozor]

How to wire the pen holder motor, because it has five connectors while the cnc shield has only four connectors for each stepper ? Thank you for this great project.

[@ashiksaleem360]

Pen is controlled by a servo i guess

[@raul7293]

I like those Indian drums in the background. I use that those sounds meditate. I like the video. ThanQ

[@dhanakodimani4783]

I followed all ur steps..in gcode sender.. i upload a gcode file.. it doesnt working..

[@michelgroenen9408]

Where must i the belt together ??? I make this machine but wen i rotate one motor the machine move in 2 direction

[@hardikvora8756]

Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall. I do not know if it has to do with the gcode file created in inkscape. When I am printing the pen is always in the same position, it does not go up or down. Can you help me?

[@EmptyChannelMC]

Nice video. Wanted to see how the movement work, it looks like CoreXY.

[@bwalker7143]

I have just built one like this but the controls are 45 degrees off as the clock turns. Is there something GRBL or $$ that can be changed to fix this?

[@amrzakaria5290]

Good job , can you sent new link for your files.

[@marting.4350]

Can you please share the software and firmware link. Link is dead

[@omtapkir8639]

There are no endstops for homing?

[@thetungtran5575]

how to wiring motor to cnc shield board, please master ?!

[@ln4951]

Подскажите пожалуйста куда подключить серву и нужен ли драйвер Zоси на шилде (при использовании сервы)? Собрал как в видео, все заработало. Есть необходимость на Z поменять мотор на серву. Пробовал grbl файл для сервы - машинка не работает совсем.

[@williamnguyen686]

If I increase the length of each X axis and Y axis to 100mm, do I need to change the code and modify the software? And where do they change?

[@icetoolz2486]

классный станок, классный видос, классная музыка) Теперь осталось сделать так, чтобы в штатив можно было и фрезер поставить, и выжигатель...

[@AnupumPant]

Could someone please explain how do the belts go around the pulleys? I just don't understand because it's all happening inside and it's keeping me awake at night.

[@RJFeddeler]

I just responded to one of the other many comments asking about the belts and see you asked just 6 days ago so I wanted to make sure you saw it so I'm posting it again. kzbin.info/www/bejne/lZ_dqXqFgM17ibs

[@GoutamNarayan]

If I want to increase my plotting area, what should I do? Will increasing the shaft size only do the job or shall I need to modify the electronics and code also?

[@jeanraines3215]

Why can't the STL files be opened

[@richardhargreaves8132]

which inkscape plugin is being used to create the Gcode?

[@zainabalshouli5166]

how did you connect the 28byj to the shield? the 28byj have 5 wires i you need 4 for the shield.

[@mohanmony01]

Hi there. I got little problem when i make a print it printing 45 degree angle why it’s happen?

[@sandeepthale8477]

Too awesome work dear... Can we use same mechanism for 2axis hotwire CNC machine?

[@jantatarski5716]

Hi, can you put a drawing file for example square or rectangle, because i have probably connected the wrong motors.

[@Kri5A]

How do I change the surface of drawing area ? I want to build a drawing machine with an area of 100cm x 100cm .

[@fauzifauzi2692]

really creative

[@ChristopherDesa]

I was so impressed with your build. That I also build 1 like this. But theFiles and software link is broken. If you could share the files please

[@abhisheklawand6382]

how to make plastic stage ,end 1, end2 ,pen holder and its procedure

[@maxyar0n]

Hi Konstantin, Great job, I like it. I already build similar drawning machine, but have a problem with calibration xy axis. Can you tell me please, how to set the working surface of the machine (via inkscape or by arduino?) Thanks in advance.

[@sagnikghosh630]

Same problem with me...did you fix it?

[@antonioceddia3278]

I would like to buy only the plastic parts, how can I do?

[@srejth]

What is the length of the threaded shaft and what is the measurement that it can draw (ie, Draw a maximum larger border line measurement L X W) Please reply..,...

[@rekhamahrana2007]

Very nice video ji

[@TheKingAdel]

New link for writing kit please

[@ED-zp8zn]

Hello, may I ask does this work with colour paintings? Thank you.

[@impedrofer]

Can you just say what type of screws you are using. Type and dimensions please.

[@u-lo-l]

I want to know how belt was connected

[@trangiaquocbao]

Please explain

[@maximilianluv1]

i find amaizing what u did !!! And i want to make also one like u did, at the moment i study electronics and i think it will help me a lot. a detailed instruction i found also at the website adress that you provide in the description but i need to know if : do i need a 3d printer ?? do i need linux ?

[@tonnguyen1531]

Can someone help me?. Why have some change the code in 16:33 ?? What is the function when you change this ?

[@neirodrigues4159]

Very very very gooooooood !

[@BecauseGames]

Wow, nothing like checking your final edit before uploading huh

[@jamilbarbar]

Good project. Could you list the bolts, nuts and screws, etc.? Thank you.

[@saurabhtyagi4329]

I want to all plastic material. So plz help me

[@user-pr4ki5yi6u]

What is measured by the size of drawings of 3D objects?

[@FlyZoneRU]

Можете помочь сделать такую штуку для написания конспектов, пожалуйста?

[@nathangonzalez382]

Hi, I want to know how I could get the whole package to put together and how much would it cost? Thank you .

[@mariacifuentes7198]

Hi, how do i modified the code so that it recognizes M3 and M5 commands?

[@MrBobWareham]

what can I say magic the music and video well done and thanks

[@The025697]

good day ! tell me how to tune the servo motor in arduino by 90 degrees of deflection and then return to the zero point! I need to attach a marker! Thank you

[@oldmemo937]

You need to tune it in gcode. Watch this. At last there are two options. Mess with the values.kzbin.info/www/bejne/fmbCmmuoqqaLpNE

[@trexarain794]

Can it be used for writing?

[@nemoskull2262]

i still dont get how you get 2 axis motion with both stepper on the x axis...:( didnt show the cable routing.

[@RJFeddeler]

I've been designing my own and use the same belt system. I found this video which explains the motion: kzbin.info/www/bejne/lZ_dqXqFgM17ibs

[@melvinjaysewane7762]

@@RJFeddeler thank you for the link and saving my day pal.

[@battleprasad24]

can you send me link of software and program link

[@trexarain794]

Can it be used for writing

[@shinlau3002]

thank you for the stuff. what is the firmware you used to control the Z axis with the 28BYJ-48 12V Stepper Motor please?

[@Shinobi_Chronicles]

sir can you plz tell me that how did you mount that gt2 pulley..?

[@lordelectron6591]

Can i use longer screw shafts For bigger drawings?

[@bayunugrahasuparto9639]

can you provide 3d printing file? thank you very much🙏

[@francisconoronha7458]

Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall. I do not know if it has to do with the gcode file created in inkscape (mac), or if it has to do with the program I use to print (cncjs - mac). When I am printing the pen is always in the same position, it does not go up or down and gives the error id = 23. Can you help me?

[@francisconoronha7458]

Hello again Konstantin Konstantinov, I do not use any command in gcode to control the Z axis. I simply load the gcode file that was generated in inkscape and say to print. What is the correct way to do, and how to command the Z Axis?

[@francisconoronha7458]

ty

[@SFan-im2tv]

Please anyone can help me ? I want to build same one, but bigger, were can I buy the staff please help me

[@mgssivaprasad2484]

This machine worked based on inkscape Android application or not..??

[@saurabhtyagi8599]

Sir I want to only orange pvc matrial pieces

[@saurabhtyagi8599]

Pvc part needed

[@sainishiv3484]

how to insert belt plzz explain properly

[@chikenpaww]

Where the hell I can buy those 3d printed center plastic

[@sandipsen7926]

Mind blowing ideas....

[@michaelnoardo3315]

do you think it is worth using this project for a 3d printer?

[@sainishiv3484]

how to insert belt explain properly

[@jarifittehad4986]

You are genius

[@vishnuprem8437]

Greetings from dubai! I plan on making this same arm. Can you explain in detail how you connected the belt? Also can I use this same mechanism with longer rods to cover 40x40 cm paper?

[@vishnuprem8437]

Ohh okay got it. Just to clarify you are using just one single belt that runs through the arm right? Also what is the reach of the arm in the video?

[@GroGaloraGran]

Did not understand the GT2 pullout scheme of the belt (

[@AdamVenomStudios]

Hello, good job on builing it, looks great, thinking about making a similar one. What plastic did you use for parts? How much money did you pay for printing more or less? Peace!

[@g2david]

How can I connect to servo? which pin should I use?

[@carlosceballos2024]

Hola, amigo como puedo adquirir ese producto. Por favor ayudame.

[@anshifa6996]

What is the torque of this stepper motor

[@naveen_yadav]

what is the total cost

[@NIKHILkumar-gp2cf]

How did u assemble belt

[@joshclark44]

Where's the audio?

[@krunalkevlani9026]

Can you tell me the scale size of all components please

[@francisconoronha7458]

Hi, Konstantin Konstantinos, congratulations for the video. It's very useful. Can you send me the link to the 3D part that supports the arduino. That it does not exist in the site where they are, another. Thank you

[@francisconoronha7458]

thank you Konstantin Konstantinos

[@skrap87783]

как подключить 28byj stepper motor там ведь 5 выходов???

[@farqadal-safi2999]

Just haw u connect the GT2 belt ?? plz answer

[@sametgok8754]

HELLO ... GRBL MASTER FOLDER ARDUINO LIBRARY NOT ADDED. NO LIBRARY. YOU HAVE SHARED AGAIN. THANKS

[@fabiano29ful]

plz post eletronic installation

[@eko653]

What kind of 3d printer is this?? I would like to buy one but I have no idea what should I choose...

[@eko653]

the malyan m150 doesn't look very promising to me... Witch one do you use? I am looking right now at a Tevo Tarantula what do you think of it?

[@peekaboowi2668]

I tried to download the gcodecreate.zip but it said that it is a virus. Can I get a safe download somewhere?

[@onluyentoancaocap8911]

can i help you peeka? i installed it. and using it. not virus.

[@williamnguyen686]

I can change use size machine (500mm-long and 420mm-long) ?

[@tinyfeeme4411]

William Nguyen of corse!

[@doitdude684]

Send link of this background music

[@mehmetgunes9252]

Can you share if there is a grbl download link?

[@TheAbubakarbaig]

what happens when both motors go in opposite directions

[@TheAbubakarbaig]

i mean to say lets say we have some clockwise distance on x and anti clockwise distance on Y, now your mechanism should get jam

[@y3d_cgi]

Where is the arduino mounting part?

[@mostafaabdelraheem5448]

but I have a problem with servo motor if I write m03 S80 or S "any number" the servo motor is move but after that it remove arduino . I am connection V+ and V- from power supply. and signal from arduino And i unify V- between arduino and power supply. same problem former that servo move I first time but In next time that's never move

[@mostafaabdelraheem5448]

Konstantin Konstantinov I test it that's arduino is remove from computer same I remove a cable

[@mostafaabdelraheem5448]

Konstantin Konstantinov GRBL 1.1 and I edited same you explain in this vedio

[@mostafaabdelraheem5448]

Konstantin Konstantinov I use stepper motors in X & Y axes that's good working and I use servo motor for z axe

[@mostafaabdelraheem5448]

Konstantin Konstantinov in servo motor I test it by three different servo motor first . blue servo 180 degree scand . metal gear servo motor 180 degree Thirdly, metal gear servo motor 360 degree and I have same problem in all of them