Dreame L10s Ultra water dispensing check

A few tips on how to check whether your L10s is dispensing water while mopping. If you’ve got no water in the base to start with, use the dock self clean (I had to do this about 10 times before water appeared). You can also try the dock self fix option too.
Hopefully Dreame will allow the robot to dispense more water while mopping in the future.

[@tom9380]

Detailed showcase of the how the mopping functionality works ! Thanks for this, haven't seen this anywhere else yet.

[@TomPattison]

Glad to be of service 🙂

[@VeroloxLP]

Excellent Video! Detailed, Short and straight to the point. You deserve a medal sir.

[@zepultra2573]

Thank you so much for your video. I just purchased this robot and the mopping function didn’t work. I thought my robot had a default ! I followed your instructions and everything is working wonderfully well. You are a life saver!

[@TomPattison]

Great! Glad I could help. Mine is 5 months old now and is still performing perfectly 👌🏻

[@lovejesus1393]

My manual on page 9 talks about Base Station Buttons. It really tells you to use it to clean the base bottom. You get the base wet and then use brush or washcloth to clean it. Then it will suck out the dirty water. The grate over it comes out to clean.

[@thomasbihn]

I have water coming out of the two channels and used a straw to pull water from the center nozzle. The mop is now at least leaving enough dampnesss I can detect by touching the floor right behind it, but this is on the highest wetness setting so would expect it to not be bone dry within 30 seconds... It seems it is running water through the mop heads so water is getting to the tank in the unit, so I think I'll run several mopping cycles to see if that can make things run more smoothly. I'm considering giving up on this brand already. With their apparently poor QC, it seems I have a good chance of having the same issue if I request a replacement. I am thinking I'll request a refund instead if I can't get this thing to perform properly.

[@sarahdara11]

I have done the home button at least 9 times and did the straw method. Water comes out when I suck it but still doesnt dispense water.

[@TomPattison]

Try filling the clean water tank right to the brim first. If that doesn't help, you could also try removing the clean water tank and tipping water down the intake hole while holding the home button down. It should work eventually 🤞🏻

[@SIRTANKTHEBULLDOG-sk1uz]

I have the same mop. But my mop pads keep falling off. Any suggestions. It only happens occasionally like every other day

[@alvinng5350]

i notice after each mop time, the robot disperse dirty water into the dirty water tank but the amount of water is very very little? is it normal? cleaning around is around 70m2

[@starvictory7079]

We have the same issue. Tried straws but nothing. Will try to find a syringe.

[@djokal]

For me, Auto-add detergent is disabled in the app, and I just replace the detergent bottle. Even if I put the old one back is the same. Any idea how to fix this? And check if the detergent is added.

[@VeroloxLP]

However, one quick question: When doing the deep clean of the base, also the middle dispenser (for the robot) releases some water. First the two bottom left and right dispensers start, but in the last second the middle one as well dispenes some. In your video it does not do this. Is this a defect of my base?

[@TomPattison]

No mine doesn’t do that. However I’m sure a little bit of water from that nozzle isn’t too bad. Thanks for watching 👌🏻

[@OMPTraxxs]

I have the settings for wetness also on maximum. There is water coming out but not as much as i saw in you video. Could there be anywhere a little chocking and is it possible to clean it ?

[@MatTeague]

Thanks for the great video really helped. For me however, base station is filling with water and the injection whole at the back of the robot has water on it, like in your video. It was as you video with the drops two days ago but since, when I take the pads off the plates have no water on them and there are no drops so I’m not sure what’s going on. From what you say it seems the robot is being filled with water but just not releasing it. Everything else though is great about it from my experience

[@TomPattison]

Thanks, glad it helped! If you read the other comments I think Maxairgo had the same issue after a few days too. You may need to use a syringe to pull water from the robot fill nozzle to fully remove any air 🤔

[@3o55]

Hello, after how many minutes or square meters does the water come out?

[@MaxAirGo]

After about 6m^2 it starts to release water in bursts of 5 seconds every 25 seconds or so.

[@3o55]

@@MaxAirGo Thanks

[@m.kaschi2741]

I have the L10S pro (no station) and there aren't any water droplets coming out even though i hear the pump. The water tank (has to be filled manually on this model) is full and I also assured that there is not blockade within the pipe of the tank. So the problem seems to be the internal pipes from the tank output to the bottom holes. Anyone had a similar issue and was able to fix? I will try to suck / blow from the bottom holes using a syringe. But first i need to get a syringe. Any tips / help welcome :)

[@bowsh6893]

Did you find an awnser to this? Tried syringe and new water tank but still no luck

[@m.kaschi2741]

@@bowsh6893 Couldnt try it with a Syringe yet but tried it with pc cleaner (pressured air) and it didnt help. Eventually i will open it.. or send it back. i bought it on Amazon Warehouse Deals. Lmk if you find a solution :)

[@664662]

Thanks for this video. I'm about to buy it. One question though: Is the detergent refillable or you need to replace the whole piece everytime is finished?

[@TomPattison]

No problem! You can either buy a new detergent cartridge or fill the old one with another cleaning product. Have a look on Aliexpress and you will see they sell a ‘non official’ refill syringe 👍🏻

[@miki3799]

my robot only 1 month, but now the wiper not working, anyone know how to fix? or can connect with Dreame support? :(

[@jpthsd]

it's been months ,,,how's Dreame L10S Ultra servicing your vacuuming/mopping needs? any issue?

[@TomPattison]

Still good after 8 months - Actually slightly better due to firmware updates 👍🏻

[@xloweric]

But does it continue dispensing water every time? I just returned a unit because water stopped dispensing after 3-4 minutes every time it ran. I am waiting for the replacement unit to show up. I hope this isn’t a design flaw in all units, but I am becoming less optimistic. Will see what the new one does. Sigh.

[@TomPattison]

Hmm interesting, I’ve got no reason to think it doesn’t continue to dispense water. Perhaps I’ll check later! I think the main problem is that the amount of water dispensed, can’t keep the mops wet enough. Although going back to the base would solve that.

[@MaxAirGo]

Did you get the replacement, how is it? I just ordered L10S and hope no water issues and is better than RR S7+.

[@xloweric]

@@MaxAirGo no I am still waiting. I emailed support yesterday to check and they are supposed to be following up with the warehouse to get a specific date for the shipment. It’s been a week since they received my unit back. I would have returned to Amazon but they only offer a refund so I would have lost my great price.

[@MaxAirGo]

@@xloweric I hope you get it soon and it works as it should.. I am expecting mine tomorrow.

[@cykr0]

Well same here, it starts with much water and after a few minutes it’s just wet, not slobbery. It refills after every room but not when it’s empty… Chinese logic things I guess

[@jpthsd]

it's been months ,,,how is the water tank on the robot going? Is there any mole?

[@TomPattison]

Hard to tell really as you can’t see the tank. All seems fine though and still working well 👍🏻👍🏻

[@SorryIAteYourCookiesSanta]

I wonder if drilling the holes slightly will improve water flow🤔

[@MaxAirGo]

I don't think so. It's controlled electronically. It has to be done by firmware update. But then you will simply run out of water to soon with the small 80ml tank. I don't know what max area it runs out of water on max setting. Anyone know?

[@TomPattison]

I’ve done at least 18m2 with full water and it didn’t stop flowing. Also, apparently the water tank is 180ml not 80ml as it says everywhere 🤷🏼‍♂️

[@MaxAirGo]

@@TomPattison That is interesting. If you have a bathroom scale that can measure grams, you can see how much lighter it really gets. Looking at inside pics of L10s onboard tank and comparing it to S7 maxV 200ml tank, doubtful L10s is 180ml.

[@Trickster2212]

Is this with the mop settings at maximum wetness?

[@TomPattison]

Yes it is 👍🏻

[@TristynRusselo]

Mine does not leave drips! Customer support has been giving me the run around.

[@TristynRusselo]

My l10s ultra was sent back 2 weeks ago. Waiting for refund. 10 months old.