Part 2. Side b of the cylinder. A quicker cleaner drill
Пікірлер: 54
@Campervanlifeforever8 ай бұрын
Thank you did this today because lost my back door key took 10 minutes to drill and fit new lock , only had one stuck pin that came out easy
@kara88bg3 жыл бұрын
If it took 12 minutes with power tools and equipment and all the noise in a workshop. I call that good lock. 12 minutes is enough for even police to respond to a call. This lock and a decent alarm system would probably defeat any burgler.
@LondonLocks2 жыл бұрын
I'd of picked this silently in under 5 minutes. this is a very worst case scenario.
@stephenupdate14802 жыл бұрын
@@LondonLocks but these are hard to pick without gj picks normal standard picks would be impossible for a lot of locksmiths that’s why they normally drill unless they have gj picks
@LondonLocks Жыл бұрын
@@stephenupdate1480 easy to pick, with skill, with any flag pick set.
@chrispink7225 күн бұрын
Is this an anti snap cylinder lock ? I can see the groves on the outside ?
@boxingmessaboutwithmydonro334711 күн бұрын
What lock was this
@Pwr2ThePeople2 жыл бұрын
A Locksmith showing people how to drill locks, no wonder the games shot
@LondonLocks Жыл бұрын
exposing the flaws in supposedly good locks will only make security better in the long run.
@koofa94024 жыл бұрын
Nice job mate.
@benfletcher2842 Жыл бұрын
Hi have you had many jobs where the key is stuck in these ultion cylinders as if they’ve gone into lockdown I’ve had quite a few now wondered if it’s a common issue? Thanks
@LondonLocks Жыл бұрын
It is a common issue. "Apparently" Ultion have fixed this with the newer cylinders. but we'll see.
@bobnoke69802 жыл бұрын
Jesus Christ , these locks are a piece of piss to pick , under a minute with a bit of practice , I wouldn’t install one on a shithouse door.
@greyskys21792 жыл бұрын
It took 12 mins because he was trying to show content you plonkers!! It’s not all about robbery’s, most of the time it’s lost keys or stolen keys Good job 👍🏻
@franciscodiez59072 жыл бұрын
Can you do the same with a KESO 8000 Omega 2 Ultra ???? Called the terror for any locksmith...
@LondonLocks Жыл бұрын
a different approach is required but it would be possible.
@applesid239 Жыл бұрын
magi burr turn it to dust if its destructive entry,
@LondonLocks Жыл бұрын
They didn't exist when this vid was made. This video was more that an anti-drill lock can be drilled.
@peterstevens7061 Жыл бұрын
@@LondonLocks I understand thankyou
@BD90..3 жыл бұрын
If there is a tool to make it there is a tool to break it.
@krcright97463 жыл бұрын
Question -- I have this cylinder, Key spin but no cam movement at all on the one side. other side works perfect. anyone come across this before ?
@vryko85673 жыл бұрын
Yes. I see this a lot. lots of issues with Ultions.
@LondonLocks2 жыл бұрын
yes. they're not very good. probably one of the easiest cylinders to pick too.
@highgatehandyman6479 Жыл бұрын
Had to drill a Yale type lock today. Picking didn't work. Made me wonder about bantam locks. Can they be drilled so easily?
@LondonLocks Жыл бұрын
There are many bypass methods for Banham. but drilling is possible if you know where to drill.
@RunninWithScissors Жыл бұрын
The racket that needs to be made to drill one of these would wake the whole street up. If someone drilled mine like this i'd have time to have a cup of coffee and a few practice swings of bobby the baseball bat before whoever is drilling came through the door.
@LondonLocks Жыл бұрын
This isn't a burglar method. obviously. This is for locksmiths.
@87tomski2 жыл бұрын
What about the two anti drill chrome pins at the start of the lock?
@LondonLocks2 жыл бұрын
in the 'part 1' - kzbin.info/www/bejne/mnmUd6Zjbppmra8
@LondonLocks Жыл бұрын
slow and steady pressure and they melt ;)
@vincentx99973 жыл бұрын
Worst lockpicker ever
@LondonLocks2 жыл бұрын
this is a worst case scenario. These lock pick easy in under 5 mins
@jameshunt8373 Жыл бұрын
No need to pick it if the cylinder is being replaced
@ObbardProductions9 ай бұрын
@@LondonLocks What type of pick would you use?
@bernardhaegeman84892 жыл бұрын
Next time use a tweezer ...
@wheeliehigh Жыл бұрын
I would of run my drill in and out until all pins are gone. Definitely quicker
@LondonLocks Жыл бұрын
Hi. The hardened pins would ruin even a TCT bit. Slow and steady is the way with 3* cylinders.
@carthstar8 ай бұрын
Just wondering if you could give me abit of advice I’ve got a union barrel lock an someone has jammed wood inside of it an I’m sure they have put some superglue on the wood and shoved it in have you got any idea how I can get the door open
@LondonLocks8 ай бұрын
Hi. in all honesty, unless you know where to drill, I would call a locksmith. but if the door is open, just remove the latch and swap the cylinder out.
@carthstar8 ай бұрын
@@LondonLocks cheers mate no there’s abit of sourness going on at the place I work an they’ve decided to mess it up while it’s locked
@SouberTools2 жыл бұрын
Check Aldridge Item No. L32382
@LondonLocks Жыл бұрын
We use these now also. Great bit of kit. Thank you Paul.
@markmenow2day2 жыл бұрын
new to this locksmithing, would a core puller help along ?, thanks.
@LondonLocks2 жыл бұрын
would probably set off the firing pin and lock the cam.
@stmp27573 жыл бұрын
Invest in a mount for camera.
@LondonLocks2 жыл бұрын
agreed. Sorry.
@1stcalltuition3743 жыл бұрын
Beautiful. Do you think this would work on most 3 stars?
@LondonLocks2 жыл бұрын
with the right bit and skill, yes.
@LondonLocks Жыл бұрын
slow and steady yes. rushing and pushing to hard normally causes issues.
@Dime_Bar3 жыл бұрын
12 minutes of drilling, banging and rattling the door don't you think someone would notice and call the police? My god they could walk it and still catch you while your drilling away at the lock.
@LondonLocks2 жыл бұрын
This IS NOT a burglar method. this is a locksmith method to drill when the cylinder has failed or been compromised.