Drilling and Sampling

What's going on below the ground during drilling and sampling

[@feigenbrot]

Finally someone who explains in concise detail how the whole process of drilling works. The animation really helped me understand all those details that mere filmed material wouldn't. Thank you!

[@MasterCivilEngineering]

Visit here

[@devonandrewmills]

This is extremely helpful! I'm in a Resource Drilling diploma program, I cannot express how excited I am to have found your channel.

[@user-ko3yw9xb9p]

Thank you very much for the vivid introduction to the beginners of geotech. You must have open the door for many students around the world.

[@karimkhan1156]

A very comprehensive description. THAN YOU.

[@guesswhotutu]

Thank you! The animations were really helpful.

[@MasterCivilEngineering]

Good

[@91Nachone]

Thank you for share this presentation!

[@nadunwijeweera4137]

Very clear and precise, thank you.

[@MuhammedRidhaSuhail]

Thank you, professor. This introduction is not just for engineering students, I think that anyone can understand and benefit from it.

[@Halfevilracing333x]

Good educational video. I think most drill operators could benefit from a quick watch👍👏

[@shehadehkhoury4666]

Great work-Thanks for your efforts

[@aksharas1704]

Awesome video I totally visuallised it

[@niel_ayo]

This is really helpful and easy to understand, thank you very much for this video

[@prodigyralte325]

I like this video.. Really.. It is helpful for me... Thanks you Air

[@evertonbarbosa9893]

Excellent video! That was very helpful, thank you!

[@GenaEnSamIAm]

Thank you professor Kitch!

[@raneemmatooq6805]

Thank you , Very helpful video

[@158nehagupta6]

Excellent video Thanks sir

[@teebamohammad7142]

Thanks for the video about site investigation

[@lakeman6938]

Thanks a lot prof Kitch,how can I access more of tour videos I found this one really helpful

[@abderrahmankadiri]

thank you professor !

[@miazmii28]

Very awesome illustrations and explanations. Thanks.

[@jafarnurulikhsani9893]

Thank You very much sir The video and naration is very clearly

[@GeoAlex71]

Thanks, That's very helpful.

[@k4x4map46]

excellent!

[@teebamohammad7142]

Thanks for this informations had helped me a lot

[@ssibaprasadpatro]

Thanks for the detailed study 👍

[@MasterCivilEngineering]

Good

[@mushtaqdass7421]

nice sir.. thankyou

[@zainabibrahim3002]

فيديو يختصر الكثير ويُبين الاكثر 👏🏻

[@user-lt1jv3fw2y]

ممكن شرح مختصر بالعربي

[@nhazilodeocleciano1055]

i Loved it

[@MasterCivilEngineering]

Step by step video solutions of civil engineering questions

[@user-ko3yw9xb9p]

Is this video made by powerpoint? clean and concise

[@musawirhussainrahi5689]

Have good information sir

[@muhamadshukur7573]

Thanks for presintation

[@danotorioust2867]

When the drilling and you have reached the test depth you stop the fluids flowing through the drill head and a hose will attached to the casing whicjmh can constantly fill the hole as the rods are removed

[@3rfansaleh599]

nice..

[@luisaifunao]

Wow

[@genesismadera9702]

this just seriously saved me. thanks :D Had to report about wash boring but no presentation in google actually gave visuals.

[@milfardonutaarsada7083]

thans for video..

[@etiennesa1723]

THANK YOU KIND SIR

[@lifeisgood9474]

nice video! can you make a video on designing a retaining wall?

[@danotorioust2867]

He is a geotechnical engineer He tells structural engineers how hard the ground is they design the footings

[@jasonlewis460]

@@danotorioust2867 Not necessarily true geo techs, design various retaining walls. There is slope factors, lateral earth factors, seepage, drainage, determing types of soil is vital information needed for a retaining wall.

[@mjunaidasghar8613]

Good

[@Berlintheking]

Thanks for this video Sir

[@rossyharinthratnam3786]

Thanku

[@danotorioust2867]

Pls tell me where I can see a drilling rig that uses the rotary mud technique without casing as a normal practice. Can you imagine the amount of drilling fluid you would need if you just pump it out of the hole without retaining it. If a pump can pump around 100L a minute and rotary mud drilling 1.5m time will vary from 1min to 30 minutes so to drill a 50m hole at a rate of 1.5m per 3minutes not including the amount of time it takes to do a test U50 could be up to 10m and an spt could be up to 20minutes so to drill like this I would need an Olympic swimming pool worth of water.

[@ahmedobidat1743]

Concerning the Standard Penetration Test (SPT), it is considered a casing method, right?

[@introductiontogeotechnical4976]

The SPT is a sampling method that also provides a measure of in situ soil properties (the N value). It can be performed in a cased hole or an uncased hole.

[@danotorioust2867]

An SPT is a 450mm long hollow tube that is lowered to the bottom of the hole a slide hammer and anvil are attached to the drill rod and 3 measurements of 150mm are marked on the drill rod the engineer counts the hits for each 150mm section the first 150mm is for cave (cuttings still in the hole) and the next two sections hit count is recorded the two numbers add up to make the N value Example test at 24m will read like this on the bore logs 24m spt 8-12-16 N= 28 If the soil resistance is great then 30 hits for the first 150mm the test the test we be terminated and the depth targeted to test

[@premrathod-xl2fk]

Add more this type of video it really helps 👍

[@danotorioust2867]

Also hollow flight augers are basically useless in anything but soft soils and for shallow holes. Also no drill rig actually hits the casing into the ground it has to be pushed or drilled into the ground. Almost any drilling capable of drill over 6m will not use hollow aurgers

[@ronaldwilkins6056]

I took a borehole to a total depth of 80ft in downtown Chicago in the mid 90s...pretty sure I used 6 1/4" hollow stems.

[@danmusiime3394]

This video explains to detail the drilling process

[@avinashgupta611]

good

[@Rezzashah67]

How to collect sample for rocky soil ? as shelby cant be obtained in such strata

[@ronaldwilkins6056]

Split spoon sampler driven by 140# hammer free falling 30" if I remember correctly...you get the sample and penetration data. I ran a geotech rig about thirty years ago.

[@kyleranderson5557]

I need to get video of this it’s my living

[@gameplays731]

How about percussion drilling

[@introductiontogeotechnical4976]

In my experience, percussion drilling is not normally used is soil or rock sampling. This is more commonly use in drilling hard rock for anchor bolts or pile foundations, but not for gathering samples for lab testing. There are other drilling methods which are not covered in the webcast such as sonic drilling (very interesting method). I recently found that air rotary is a common method in West Texas. It's much like mud rotary but uses compressed air rather than drilling mud to bring up the cuttings. I'm sure there are other regional methods I have not encountered.

[@gameplays731]

Introduction to Geotechnial Engineering 😊😊 thanks for your positive feedbacks.

[@fatimaezzahrahilal6699]

5 dislikes are these people mentally okay ! this video is awesome

[@danotorioust2867]

Because he is an Geotechnical Engineer not a driller

[@exxbro_]

stavo cercando sample drill e ho trovato questo.

[@danotorioust2867]

Turn the water off and disconnect the hose OMG so when you talk about hydrostatic pressure on the hole wall yes correct but what happens if you turn off the water flow to the hole. Just think about filling your bath up hop in and out what happens to the water level. If you turn the water flow off then remove the drilling rods the hydrostatic pressure will be dramatically reduced causing the walls to actually cave in it's the weight of the drilling fluids that hold the hole open