DRILLING CONCRETE MAKES ME ANGRY (ICF Bracing / Scaffold System)

[@aSinisterKiid]

There is a reason they make proper concrete drills. I love Makita, and that cordless is a great tool, but it isn't meant for this task.

[@stevenbaumann8692]

aSinisterKiid in his defense. Drilling concrete does suck.

[@knightpunk8385]

I would use 'Bosch multi drill' pneumatic hammer is the way forward from here.

[@knightpunk8385]

If you pilot drill your timber first, you'll save battery life and the impact drill will last longer..

[@russellraposa2461]

aSinisterKiid make due with what you have

[@edbenson98]

aSinisterKiid Also never use the bits inside a box of screws, buy some high quality ones!

[@mrcjspapa]

i am disabled and retired and have followed your journey's diligently!! Thanks for taking us along.

[@sgordon1962]

Hi guys, I've been watching for quite a while. I'm a (medically) retired general contractor. I am getting worried about you getting dried in and heated so your footings don't heave, so I have to give you unsolicited advice: Throw those hammer-drill bits away! Get a Bosch Bulldog or similar SDS drill and it will pay for itself in a day of drilling concrete!

[@sgordon1962]

I just read the comment below and replies. Don't bother pre-drilling boards with an SDS bit. Happy drilling!

[@Loetmichel]

you can if the SDS bit is new and sharpened. AND high quality Tungsten carbide so it STAYS sharp for a while. But it would be easier to predrill them with a bigger wood bit in the battery drill and then switch to the SDS pneumatic hammer drilling machine for the concrete.

[@sgordon1962]

My crews used the same bits for years (I'm old) and thousands of holes and never got dull going through wood before hitting concrete. $20 for any name brand SDS bit is for a lifetime for most people.

[@ealingbadger]

No, they don't get dull it just doesn't fell right - all that heat and they are a lot slower going through timber than the concrete that they are designed for. I would have three drills on hand to tackle this task with maximum efficiency: 18V battery drill fitted with a Bosch 'Multiconstruction' bit to pierce the timber. SDS hammer drill to melt through the concrete in seconds Second battery drill (impact driver) to drive the fastener in Much quicker and MUCH less frustrating overall. (The reason for the multiconstruction bit is that it drills timber almost as fast as a standard twist drill bit but doesn't instantly dull when you hit the concrete - as you inevitably will coming out of the back side of the timber.)

[@Smurphenstein]

Dragoneyes Hatesgewgle can't you tell the drill is running in reverse. ;-) I would seriously be looking into a cheap basic drill with a hammer function. Yes, cordless drills have improved a lot but in my opinion you can't go far past a good old grid connected power drill for jobs like this.

[@loose_unit]

You are going to need a propper drill for this. We used a DeWalt battery hammer drill to drill through tiles. At some point it broke so we rented a proper "wall power" hammer drill and it took 30 seconds instead of 10 minutes to drill each hole. Well worth it!

[@elhigh]

Tips from a guy who drills concrete a lot, for those who don't: 1) Pre-drill your holes through the lumber. Use a wood bit for that. Faster, easier, doesn't put any wear on the concrete bit before necessary. Not that it would wear the bit, but it's good practice to use the right bit for the job. 2) Woodpeckering the concrete hole is a smart plan. Pull the bit every few millimeters to clear the dust, especially if you're already going through wood. It doesn't clear well through the lumber. 3) Don't use full speed. Too fast = too hot, and the bit loses temper and goes soft. At that point it's useless. I also keep a pail of water to dip the point into when woodpeckering, just to keep things extra cool. Cooler is gooder.

[@robh1683]

I think "past focus thirty" is my new favorite time of day to give to other people. Just ahead of "half past a freckle". Keep up the hard work you two. Good job.

[@MARS-fi6wq]

just a quick hello from france! you use a cordless drill with hammer function, but what you need, to drill concrete, is a rotary hammer(not sure how it is called in the US) . They look the same , but are fundamentaly different. Rotary hammer are with sds chuck, and you need sds drill bit too, but once you have used it in concrete, you will never use hammer drill anymore. for a rotary hammer, search "dewalt DCH253P2 18V XR li-ion SDS+" as an example, For the drill, check "Bosch X5L SDS-Plus Full Head Carbide for Concrete & Rebar" it will change your life.

[@donshilo2024]

This is the first chanel of construction that for some reason doesnt bore me!

[@imacrazyguy5831]

Those hammer drill modes on drills are useless for any actual work. They are a very temporary way to make a small hole for recreational use. A proper rotary hammer drill will plow a 1" hole in 30 seconds with a good bit. Definitely get yourself a proper drill, even if you have to rent it for only a few days!

[@garybaris139]

One that runs on power, use a drill that runs off power and use a generator to run it. SDS is the only way.

[@DEADB33F]

Yeah, they work ok for drilling in mortar, cinder blocks or light house bricks. For drilling in actual concrete or stone you need the proper tool for the job. But anyone who says so is a troll on this channel!

[@miket6978]

troll lol

[@SeptrothFFXI]

Buy a ramset... or put anchors on the inside forms BEFORE pouring the concrete and pour them in place. It's almost like voodoo magic!

[@JohnnyMotel99]

Yep, SDS + concrete = butter. Plus SDS actually drills the hole where you want it!

[@island97]

You guys are awesome. Building a house is so difficult, it's normal to make a lot of mistakes especially when you're not a professional. Don't worry about the negative comments, just keep doing your thing and I'm sure you'll be alright. Good luck .

[@EdDohman]

"twist, bow, and crown" have NOTHING to do with the way lumber is graded! Grade is determined by placement of and amount of knots, and how the lumber is sawn.

[@ZachTandyMitchel]

I just want to tell both of you, because no one ever does; I'M PROUD OF Y'ALL!

[@dsdragoon]

I love my Bosch Rotary Hammer Drill! Sometimes up have to brace the braces.

[@winderlininc8909]

I've been watching you two from the beginning. Your are brave souls. I built my house along time ago. I discovered that a house has a lot of parts and pieces. More than you ever imagined. I learned a lot and had many valuable experiences - you will too! Try to stay calm and have a wonder time. I'm rooting for you every step of the way!

[@nicumarc5788]

Just get a Rotary hammer....even a cordless one itl pay it's value in couple of hours!DeWalt, Milwaukee,Makita have good ones!

[@mitchellmnr]

YES! I bought myself a SDS rotary hammer with the but in the center of the drill.... and well I love drilling concrete because its easier than wood! :D

[@schwarzarne]

But then he has no reason for his favourite past time anymore: whining....

[@TroyDake]

+Milwaukee hammer drill put 50 plus holes in concrete with 1 bit easy as butter.

[@SuperUncleRyan]

I have a Bosch SDS that would drill all of those holes in the time it took him to do that one board, HD even rents the one that I have, if you don't want to buy it. Cordless hammer drills are just not meant to do bulk work like this.

[@tjjoseph333]

It's a shame these videos are days/week past complettion. There are enough folks out there with real daily building experience commenting that could be saving you massive amounts of butt ache. The first time you use a real rotary drill....you sell other things to buy one! :-)

[@moonlitphillips]

I've said it before and I'll say it again, you are doing a great job! I cant wait to see it when it's all done and dusted. You two remind me of my husband and I, this is something we would do if we were a bit younger. We have built our own garage, barn and hatchery and it is such a great feeling you get when it's all done and you can say you built it yourself. Keep up the great work!

[@wantblackwolf]

Every time I see one of these videos I think about simplicity of the old school concrete blocks. Sure lifting all those blocks would be hard work but I can't help to wonder how much faster it would be over doing all this.

[@christopherstube9473]

Every project is better when there is someone who is serious about logistics.

[@christopherstube9473]

I never had any luck with screws in concrete and always attached things with a 22 powered nail gun.

[@longhairmullet]

Too bad we didn't see more of Anna White's ICF build. Those of us who viewed that know they just showed it briefly without much fan fare. Others that have posted using ICF have a team come in and film in time lapse, up finished. So ya is it really this hard!?! So much work, thanks for giving us the real step by step necessary to complete.

[@NilanjanRoyKnowmics]

I am watching you guys from India everyday, Both of you guys are extremely hard working. I salute you guys. Best of luck

[@danielhughes6896]

watts is not a measure of energy, its a measure of power. energy is measured in watt hours or joules. Watts is a measure of how much power is being used or generated at this instant. If you want to know how much energy you generated in a day you need multiply the watts times the amount of time you generated that amount of watts for. This is measured in Watt hours (Watts times Hours).

[@osgancha]

I will probably never do what you guys are doing but I find it extremely interesting I don't miss an episode

[@darryldee467]

20:21 DANGEROUS SITUATION. Standing on a narrow, flexing board like that!

[@tim_bbq1008]

thanks for the show again. watching you drill wood with a concrete bit has turned into my evening entertainment.

[@gregormiller4037]

I just spent the last 15 minutes reading all the very helpful comments. Hey Jesse, I suggest you invite everyone in comments to join you, have them bring lawn chairs and shout out 'the right way to do this is...". It would make for a more entertaining vlog and you Shirley will get the house built faster.

[@ori4640]

some People do not know how to be generous, the writing bad words, the courage of those couple to perform tasks they have never done is amazing, both of them are very special persons, stop insulting them morons, and help if you know or can, and if you do not want then shup up, I wish them a lot of success.

[@lowercherty]

Why are you putting untreated lumber next to the ground?

[@drhud1524]

You're wife is such a blessing my friend! I'm excited and wish I would be able to come out and help you out for a couple of week!

[@hotchef1984]

For the future make sure you are wearing a dust mask when drilling concrete. Silicates are horrible for your lungs.

[@butch0320]

I have been following along with your videos and must say how impressed with your fortitude and obvious strength with all the work you are taking on yourselves, kudos to both of you.

[@joylovingyeshua5861]

We want to do exactly what your doing, want leave S. Cali. can you tell me what the house will cost?

[@Approx_99]

50 monies

[@ferky123]

Joy Jackson 65 units.

[@XLR8RRICK]

Dont look for help from these people, just watch to know what not to do. They dont read or answer any of the comments. So sad.😨

[@slowburntm3584]

Houses today average out to about $225 a square foot to have built, but the more friends you have for free labor the cheaper it will be. Also, you should almost always be prepared to spend more than estimated, ESPECIALLY if you have never done it before.

[@MarthaMedicare]

Joy Jackson, are you part of the Great California Exodus?

[@bfw6971]

Been watching this series for awhile... I think most of the negative comments I have read are ridiculous. This video series does not hide anything and this couple owns up to any mistakes they make. Yeah he might screw up, but he shows a video explaining that screw up and what he learned. I have honestly learned alot because I approach things the same way... Trial and error leads to learning.

[@bj5147]

concrete drill bits work on stone/concrete but if you hit rebar it will stall and burn.

[@MsSomeonenew]

Does the same thing on a rock, as they are so much tougher then mere concrete.

[@mitchdehotte]

Rebars ? Wich one ? Hve you seen the video of the foundation ? This man and his house is just a pure joke !

[@ThisOldMan-ya472]

The best development in this project is Alissa, going from great to awesome.

[@00750r]

Should use a corded drill a better bit and pre drill the wood with a wood bit .

[@super_slo]

I thought the same thing about pre-drilling the wood with a more appropriate bit. Looks like it would greatly speed up the process.

[@00750r]

He won't be able to keep up with batteries anything over 10 holes I use corded HD.

[@graceandglory1948]

You guys are amazing! I am so impressed with your attitude, your work, and your love and respect for one another. Blessings... Tricia

[@shellsmith831]

My husband has had a love affair with his hammer drill. He invested big $$$ over 20 yrs ago and only uses it for concrete . I never thought he would ever get enough use out of it to make it worth the price. I was wrong ! It is still going strong after one cord replacement. When he joins in on a job and he breaks it out other Men ohh and ahhh at how well it works and then they go out and buy one too. His model is no longer available though😟.

[@hollandershomestead4481]

I don't usually read comments but the past few videos I've seen all the negative comments. Just wanted to post something more positive. I'm very much enjoying watching your build, and how well you two work together. Please don't let the naysayers change how you do your videos. Also, your work ethic is inspiring!

[@benningtoncamper2852]

Please, if you are going to show us your solar generation, learn the difference between Watts and Watt-Hours!!

[@NMjack2000]

I admire both of you for your dedication and hard work to build your knew home. You both are good teammates and work very well together. Am sure you will enjoy your home for many many years Am sure your videos will be a great source of information for others that build their own homes using the ICF System.

[@kenknutson1598]

Eye protection. Face right next to hard drilling,broken bit and an eye injury

[@idahopete9211]

Your expectations of lumber is amazing. Very often when choosing lumber at the lumber yard, the board my be perfect. Then a few days in the hot 100 degree heat. Wood moves. Basic high school shop 101. Live and learn.

[@Hookahitter]

Seems like a wind turbine may help, on cloudy days? How much wind do you get on your cliff, oh, property anyhow? LOL

[@nicumarc5788]

Yup a wind turbine will definitely help!They are about 499$on home Depot website and u just need to add a charge controller and Bam....you are done.

[@MsSomeonenew]

Wind turbines work great... in areas where you have constant wind. These guys however are in a hilly area with tree cover to all sides, it is extremely unlikely a wind turbine would do anything for them.

[@LMiller658]

OMG, I am proud of both of you.

[@rollerben88]

rotary hammer......rotary hammer......sds.....sds......sds......rotary hammer........rotary hammer.......sds hammer drill.... I know it is probably too late though as this could have been filmed a couple of days ago

[@rickr7333]

I love my cordless drill! It's a lightweight tool that does a lot. There is no way that a cordless drill is suited for drilling concrete or any other heavy duty operation. For drilling hard surfaces, you need a power source that has lasting abilities with serious power, so it needs to be power mains (120VAC/240VAC) corded electric drill or compressed air (pneumatic) drill, period! You have brought a knife to a gun fight!

[@Lennart_Jensen]

My Health Environment Safety antenna vibrates something so sickly when I see a small plank between the two step ladders. And all this stacked on top of a pile of loose stones. You must think about your health. And not least because I want more youtube episodes from you!!!!

[@VinceW187]

Awesome to follow the progress over time, wish you guys all the best.

[@pronkjap]

Please get the right tool. It is a pain watching you struggel. And protect your ears you will mis them when they dont work.

[@mwilliamshs]

Struggle*

[@pronkjap]

mwilliamshs cheers

[@mwilliamshs]

...miss* them.

[@catsinheat]

Dang, this ICF foundation is taking forever. It tires me just watching, I can't imagine its effect on you guys. Well done!

[@superdaveofendor]

A bug-a-boo sighting!

[@FullCanoe]

Fo' realz!

[@TheGamingWarrior10]

i wish youd just livestream your life 24/7 because whenever im not watching you but im on youtube, im just thinking of when youll upload next and want to see you make major progress!! good luck on the build!!

[@NCLUSA]

Where did the old truck go?. All of the negative comments are from people that have never made a mistake,,,,,,they have never made a mistake because they have never did anything ( : . You guys are doing a great job, hang in there.

[@NCLUSA]

Louis you're a troll (:

[@NCLUSA]

yarpos you be a troll too, (:

[@NCLUSA]

I bet you are an expert on that? (: he he.

[@davithkane1369]

GOOD EDITING, (sometimes it's easy to forget how much work, time and effort it takes)

[@nmopzzz]

When I did it it took about 1 hour per minute. So figure shes shes more skilled than I, so say 30 minute total work per 1 min video. 20 min video, is about 10+ hours of work. This includes getting all of the film together, playing it to see what's there. Splicing in the scenes, then replaying and editing it about 10 times.

[@nmopzzz]

The speed of the computer is a second order effect. Let's say they each recorded 3 hours of video that day. First she has to copy the data to her system and organize it and setup the SW for that day. Say 30 min. The she has to go through 6 hours of video and decide what to use. Say she's good at fast forward and clipping. 4 hours or so. Then she combines the clips and plays it once. Another hour or two, most of this is just playing the video. Then she clips out dead time and then overlays music, another couple hours of work, and again most of this is re watching the video and editing small details now. This does not include adding the links in the video to older videos or finding the music samples. Then getting the boiler plate stuff for the video page. Then one final pass though. All of this is an easy 8-15 hours of work and most of it is not bounded by the speed of her Mac. Its simple, tedious editing.

[@emlodnaor]

The hammer function on small drills like that is a total joke, if your not done, go rent a propper one.. drilling in concrete is easy with the right tool...

[@rabiamarygraney2881]

congrats, you are over 200 k subscribers - good for you both - you certainly EARNED it!

[@russellraposa2461]

Lol left and right corners?

[@russellraposa2461]

IthinkthereforeIam OrsoIthought they look reversible

[@clintonflowers877]

Russell Raposa why lol there is left and right corners in blocks that have a top and bottom to them

[@henripapineau1610]

Seeing the issues you have drilling "Just the perfect hole" make me feel better about my frustration with the very same issue. It's hard to NOT get frustrated when it took 10 to 15 minutes and you've only drilled ONE hole... the flipside being that now you know how to do it..

[@borthewolf3376]

Unsubscribing. I can't bear to look at this amateurism anymore. Don't you guys educate yourself by reading or by looking at youTube instruction videos? - Lumber not covered, leaving it exposed to the elements, and complaining about warping. - Not using the proper tools like an SDS hammer drill. - Not using proper scaffolding. - Removing the casings while they are still needed - Not preparing the ICF build process (RTFM !) - Ignoring good advice and calling it trolling. (The first search hit on KZbin explains to work from the corners to the common joint) - Not seeking the help and advise of an experienced builder or engineer. - How on earth are you going to connect the ground floor concrete slab to the walls? Why isn't it poured before raising the walls? - Debris inside the wall to ensure the concrete does NOT adhere to the footing? - And the list goes on and on.

[@theoldtimeywoodworker2488]

Bor the Wolf. I'm calling in Ed and Willem Bever, cause these folks need some serious help from these experts. 😉

[@RPDundas]

My man, you don't need anything fancy, but even the cheapest hammer drill from any big box store will make it SO much easier, and I promise you it won't be the last time you use it!

[@cafe88racer53]

Those drill bits don't look like concrete bits

[@craigschofield64]

Oh and if you haven't already realized it Jessie you are blessed to have a beautiful lady like Alyssa who can do more work than most men and still be absolutely drop-dead gorgeous my friend you won the mans dream lottery when it came to finding a woman!

[@rsymonds53]

safety glasses dude...

[@joemoe1601]

i wear a full face mask. I don't like cuttings of anything hitting my face or neck.

[@vintagecreationschannel655]

Hey guys really love your journey and just catching up after being on holiday, just wanted to pass a bit of advice I received years ago from an old pro builder. I was complaining about cost of drill bits and poor performance of conventional cordless drills in concrete (our bungalow has lots of it in the walls) he said go buy yourself an SDS drill they go through concrete like butter. Never looked back.... a bit unwieldy but certainly worth it. Also does chipping and destruction of concrete with chisels so useful for other jobs too. Leaving your cordless drills ready for action on all those screws!!!..... keep up the great work it's awesome!

[@harleyhaynes]

The amount of garbage and negative comments on here blows my mind. Bunch of complete internet warriors. These 2 are actually out building something with their own hands and sweat and probably tears. constructive criticism is probably welcomed but some of the comments are simply unwarranted. I say celebrate what is right with what they are doing and the fact they are doing it as husband and wife, together...

[@dnmtorp]

Wow I have been enjoying this channel but not reading the comments. I came on here to give a little advice and am amazed by all the naysayers. I am learning a lot just by watching. You learn by making mistakes. If you have never made a mistake in your life it is because you have never tried anything new. And yes, get a proper Hammer drill and run the generator. Bosch Bulldog if they still make it would be adequate, or rent one. Keep up the good work!

[@diygardener4556]

Question: wouldn't concrete nails be way faster, and way easier? Second question, why wouldn't you just use concrete nails? Boom, problem solved!

[@sferris5316]

I don't get why everyone is hating on them so bad. It's just ridiculous. All the "experts" and safety sallys on here thinking they know how to do all of this. If you don't like it don't watch!! Every house build has issues and every first time home builds go through stuff. Don't listen to these know it all haters Jesse and Alyssa. Keep on learning and keep each other first! Don't forget to take a date night once in a while!

[@SB-oc6pg]

You need to stop and hire a professional before you A) get divorced B) get injured or killed or C) go bankrupt Are you beginning realize there's a reason everyone doesn't build their own houses? By the time you read the comments on drainage, scaffolding, hammer drills etc you've already gone passed the point of no return. Hire a professional before this gets beyond repair.

[@guyapeterson]

WOW! This is the first time I've read any of the comments and they're almost as entertaining as the video, but I don't think I could get through 1,391 without getting bored...

[@kathyanne3587]

Well........I am also building outside, and just want to let you know... that it is HARD work. These two are doing great.....I bet all those whinny you tubers have never even picked up a construction tool. Let alone take on the enormous task of building your own home.............And have you seen how many followers.....they must be doing something right...

[@kfstreich4787]

Kathy Desjardins I have a feeling the trolls here have little to no experience, I would do a lot differently, but I'm not doing it and the foundation seems to be headed up even with a few unconventional methods.

[@kathyanne3587]

Yes, i agree. I too have tried some unconventional ideas found on the internet. And like Jessie, what i have found is that they promote it based on one concept ( like the horizontal bracing being stronger) but the downside of everything else out ways the benefits. And of course they never tell you of the downsides.....My rocket mass heater is an example of that. I got it done in the end... but had to use a lot of my own concepts, and in the end it was a 2,000.00 dollar build, not the inexpensive build that they promote.

[@island97]

I completely agree. I watch all their videos and I'm surprised about the negative comments they are getting. They aren't pros, but they are trying their best and I love their determination.

[@samkingcircus]

omg lol!

[@brucevanderzanden9638]

Been there, done that. Built our home in 1997, and still remember the dump runs, recycling, etc.. and all the other daily things that got put off till it had to be done.

[@JieDoyle]

Leaves all lumber without bands and in the sun and rain, while he thinks it's the lumber yards fault they are twisted now. Get a clue Jessie!

[@r.blakehole932]

+JieDoyle Properly cured and kilned lumber won't twist. All of those problems used to be dealt with at the lumber yard. But most lumber today is sold green cut which, will turn into pretzels. But, we idiots today, are too stupid to know what good lumber is, or what it used to be.

[@dwwolf4636]

Nahhh the sad truth is that we dont want to pay for the good stuff.

[@Grumpy_old_Boot]

But that's the thing, he paid for Class 1 wood, and didn't get it. It's supposed to be the good stuff.

[@TopBanana48]

I appreciate you saying "we idiots." Too many people on here are dishing it out and forget that they've learned a lot of things the hard way too. I do hope they protect their wood in the future. :)

[@SuperUncleRyan]

At the very least, stack your lumber neat. It will help keep it from twisting.

[@davestargazer]

These guys are great. They are not heavy into the trades, obviously and commenting on their work just makes us sound like a haters. Failure may actually attract viewers - they hooked me. Only wish they would read and share what they learn from some very good and helpful comments. Point out if their manufacturers or engineers say different. However, trying to video, learn, plan, build and deal with YT comments must be quite challenging.

[@donaldparlettjr3295]

Like I said a block wall for me. It's up and you waterproof it and insulate it done. Plus if your drilling through wood use the right bit. Drilling wood with a mason Army bit will just destroy the bit.

[@johnhirsch5923]

Jesse and Alyissa - you guys are doing great, hand in there - this phase will pass soon.

[@markbrown3587]

I get the feeling the lumber yard you got the boards from is scamming people :( I hope they apologize, give you some free wood or maybe just never use them again. Need hammer drill, oil/soap/lube of some sort.

[@kane2298]

love watching these. i've been thinking about trying ICF myself, but it's sure not as easy as the companies make it look!

[@riadozee]

Jesse , no offense as you seem like a decent fellow but you ought to think about using this time of hard work to lose some more weight ( by the way your certainly not obese by any stretch ) but from what I understand you have some back issues and losing some weight would greatly improve that .

[@MsSomeonenew]

Back issues that are not caused by elephants are not fixed when removing elephants... I'm from a farming community and shitty advice like yours is just a daily thing, people suggesting random "healing" nonsense that has not ever worked for anyone.

[@MegaWeagle]

MsSomeonenew shows how much you know. Plenty of people have fixed back issues caused by weight gain. Does that mean it is or will be the fix for Jesse no, but it has can and will work for some people. So let's take you and your condescending attitude some where else, preferably where you will be alone and a bother to nobody.

[@riadozee]

Ms someonenew , I didn't mention any healing only that some relief may be found if stress is reduced on the back due to weight loss .

[@Marketto8777]

even if it's not direcly caused by the fat, losing weight makes your backpain feel a little better.

[@lucaviggiani2189]

I love it when KZbin instantly turns certain people into Doctors, Engineers, Surveyors and all round specialists about everything all rolled into one.

[@Approx_99]

My one and only complaint about this channel; when they use THAT music (2:00)

[@tiptap1600]

@Alyssa, one sees this going on and on and on, and one is never sure whether something actually does need to be said or not, right? Hell, I will say it... About this guy you've chosen, I really don't know... you're setting yourself up to spending the rest of your life with a self-centered man, in love with the sound of his own voice, a nightmare I truly don't envy... your choice, but are you walking into this with your eyes OPEN, girl? PS: You don't have to (shouldn't) play dumb to keep his ego inflated, it clearly is already plenty full and one would have a hard time deflating it any.

[@tiptap1600]

Yeah, I got you. By the same token I could be right, right? At least give me that... It's just that this goes on episode after episode, of this guy and his utterly transparent bs, the "experienced" member of the duo that, in fact, is all bs. I mean, I could probably be around this egomaniac in love with himself for a couple of days, after which the air would get hard to breathe -- Alyssa is choosing to breathe it for the rest of her life, and she's young! But I'm only going by what they show, of course, it's entirely possible that in real life he's entirely different than what is shown here... unlikely, but possible. But the point is that Alyssa knows what I am talking about, and I probably know a thing or two that she hasn't lived yet. Whatever... what I thought needed to be said has been said...

[@MsSomeonenew]

Jealousy always is a bitch...

[@Kat-pg5ye]

@ Tip Tap, EXACTLY!!!!

[@rixanneh18]

Did you just assume Tip Tap's gender? cuz it sounded like advice from another woman to me....not a dude trying to hit on Alyssa. Could be wrong *shrug*

[@tonycarruthers9556]

I thought thats how Australians talked

[@walt8089]

I have worked out in the heat all summer on various projects with almost 100% relative humidity, a lot of the time. I have 6 wide sweat bands that I rotate throughout the day and they really help with sweat rolling down in my eyes.

[@moparmatty98]

I'm a aircraft mechanic. I drill a lot of holes in titanium. One word of advice. You have to let your drill shavings clear. The reason why it's so hard to drill the concrete is your flute are getting clog

[@1961ebutuoy]

You should never need muscle to drill into or through concrete. My "seated in my armchair" advice, is that you use two drill bits a wood bit and a concrete bit. From experience, concrete bits have a toughened tip on the end which is melded into softer steel of the concrete bit. When you consider the effect of friction exacerbated by the amount of strength you were applying to the drill and the time taken to push, and push, the drill bit in to the wall. The end of the bit falls off and you have as much success drilling into the concrete as pushing a spinning nail into the wall. Position your wood and carefully mark where you need holes. Pre-drill holes in the wood using the marks and a wood bit, either same gauge or slightly larger. The amount of time, effort, battery power saved will be phenomenal, and give you a much happier time of it. You two are inspirational. Keep up the great work,

[@waiakalulu3501]

I've been rocking the Bosch Bulldog, and I swear that's been a good tool for concrete. Gets it done fast. They're light and cost less than 200 clams. While they've long since been eclipsed by cordless versions, I got two of them corded going on 15 years now, and they're still getting it done like a hamburger bun.

[@michaelkaylor6770]

Focus-thirty, the new KZbin official Best term!

[@FromThePrairies]

Right tool for the job dude. I rented a hammer drill last year to put in 16 concrete screws. Took 15 minutes. Would have been there until now had I used my hammer drill setting on my cordless. That hammer drill went through like butter. God I hope the next video shows that you bought/borrowed/rented one.

[@jonassjostrom9787]

Love what you do! I am a GC. You guys are doing so well. I'm impressed and must say that your teamwork through the process is a joy to watch. I just have one recommendatio. Make a quick run to pick up a hammer drill that takes SDS bits. I promise you they drill holes in concrete like butter. Good luck!

[@davidturney9813]

Yes the answer (the right tool) But budget is imporant. your looking great. good to see cat is still with you.

[@PhilipMooremba]

OMG, Jesse that cardboard is a golden garden resource. Don't throw it out!

[@HazItMade]

I hope Jesse has someone he can call when things aren't going well with a certain task. If you have future issues like drilling concrete, CALL ME. You made that a LOT harder than it had to be.

[@alienphysics8592]

I wish I lived in your area, I'd be more then glad to help out. You kids are getting lots of OJT, but just think ahead of the next house you build, you'll know more and approach it differently. Early pioneers packed it up and headed west with little knowledge of what they were getting into..... most did fine . You just have more work to do to achieve your goals, and stop often and have a nice refreshing big glass of each other because in the end that's what it is all about.

[@J3AD]

couple building a house from top to bottom, is wow, very interesting, not to many folks would do this kind of thing.

[@wessfrederick5270]

Hmmm. Im wondering if leaving the inner footing form boards would have helped??

[@Litzbitz]

YOU BOTH NEED NEVER TO GO TO A GYM FOR A WORKOUT. WOW! MY MUSCLES ACHE JUST WATCHING THE EFFORT IT TOOK TO PUT IN THOSE SCREWS. I HOPE YOU ALL ARE KEEPING UP ON YOUR ELECTROLYTES! PULLING FOR YOU.

[@wiebowesterhof]

SFS drill is your friend. Those things (regardless of brand preference) go through in no time. Where I live the battery operated versions are impossible to buy, but in the US there are a fair few options. Good luck :)

[@Foreverenpointe]

I am so afraid she's going to fall off their scaffolding! Be careful. :) Keep up the good work!

[@kodysimpson1]

Guys, a little advice. Dont drill wood and concrete at the same time. #1drill the wood over size #2 mark the holes on your concrete. #3 move wood aside. #4 drill the concrete. You see the wood absorbs the shock of the hammer drill ans it will not break the concrete at the end of the drill bit. Also use a washer on the concrete anchor

[@18twilliams]

unreal! cant imagine you actually building the house! I'm sorry but wow!

[@RemodelGC]

I must agree with others a proper SDS Bosch or Hilti rotary hammer drill will make it so much easier to drill those holes. Keep up the good work! You guys are die hard workers! Stay cool and hydrated! 💪🏽