Install/Review: JBA Catless Downpipes For Dodge Charger/Challenger SRT Hellcat!

[@thatboynyah5292]

Great work on going the extra steps to edit and be thorough. It really seperates you from the other lazies (youtubers) . Had to sub. 💯

[@JMV1777]

I just purchased the jba midpipes for my charger hellcat, only difference is that I have the Corsa extreme as my catback. I am so pumped to get it installed

[@DrivewayDemons]

Awesome! I have the corsa extreme now and tried it with the catless downpipes. Have you noticed with the corsa extreme that around 1400 rpms @ warmup idle or hold the accelerator in the spot there is a rough idle? I have that as well as a slight cabin vibration @900 rpms. When I switched the stock rear resonators back on it went away. I have done some research and learned that the corsa extreme is more of a muffler not a resonator so its leaving some frequencies alive and causing a really bassy vibe back there. I have been researching it and was going to do a video on it soon.

[@JMV1777]

Driveway Demons I have that rough idle on initial warmup! The interior overhead lights (if I have them on during warmup), dim if I lightly tap the gas during warmup! The cabin vibrations I do not have! How do the midpipes sound with the Corsa?!

[@JMV1777]

Driveway Demons i see your other video with the corsa. Going to watch it now lol

[@davidjames8613]

@@DrivewayDemons should I get the Corsa Extreme and the JBA Catless Downpipe or with the JBA Cat4Ward

[@undergod9586]

Awesome job and vid my G... Very informative, detailed and clear. Great content keep the vids coming...I just subscribed😉😉💯‼️

[@DrivewayDemons]

Appreciate it 🙏

[@KnightsGarage]

i know this has nothing to do with the video but what wicker bill is that?

[@5.0h76]

Get a zl1 addons wickerbill

[@jessw3503]

Did you need to use the factory crush gasket inside the cats or are they no longer needed with catless mids?

[@dlo__3929]

I keep getting a CEL light even after putting two o2 extenders. My guy cleared the code for me but came back after driving back home smh. Is there a way I can bypass it ?

[@triggerfocus]

DLO__392 same me too bro

[@dlo__3929]

Jerry Rocha It’s our damn rear o2 sensors smh we need a tune and unlocked pcm to get rid of that CEL. I have a oil change coming up and I know the dealer is going to throw out my warranty

[@LiyahWillsWORLD]

is it just me or do you get an accelerated rattle at about 2k-3k from the exhaust. i installed mine and i get a rattle now

[@SixTwoHemi]

Space it off the stock exhaust bracket will correct that

[@socalfun64]

Really nice job bro. Thank you.

[@italy18myg0t]

is this about the same for scatpacks?

[@2010svtraptor]

When you switched to catless you got it tuned? How bad is the smell now that you are catless?

[@TopG82]

This catless mid pipe will fit in a challenger TA 2020? 5.7 engine

[@DrivewayDemons]

Yes

[@MrLilLegend]

On Highhorseperformance the picture of this part number has 4 02 sensors ports but on this picture it has 2. im confused, because your link has it sold out . so i needed to source it somewhere else.

[@flacodominican9850]

hey i jus put the mid pipe n got mid muffler deleted n i buy o2 sensor spacers but the check engine light came on still

[@RS3_WAY]

What size boots is used for the headers to engine piece just incase I break a bolt

[@mikefuchs8122]

How much louder is this compared to just the mid muffler delete?? My mids are deleted now but looking for more volume! Thanks man

[@DrivewayDemons]

It’s a lot louder.

[@mikefuchs8122]

Driveway Demons niiiiice 👌 Great video man

[@Shelby_Moe5.2]

After you get it done, does the car leave a smell inside the cabin or no?

[@DrivewayDemons]

No smell really. I am used to it. Just super super loud LMAO

[@MBballer2]

can these steps be taken with a 14 srt8

[@DrivewayDemons]

Marc Be Hoopin absolutely! Exactly the same

[@The_Bandit_750]

So does the challenger and charger jba fits the same before I buy them

[@DrivewayDemons]

They do indeed 🤟

[@The_Bandit_750]

Bro you are the dude I was scared to buy them cause it says it don't fit, but can you send me a link for the o2 fouler I don't know which ones to get

[@DrivewayDemons]

Thanks bro. Just buy two spark plug non foulers, then drill one out the bottom hole and elongate it large. Screw oxygen sensor into it then screw that modded fouler into the other one. That's a home made version it works.

[@The_Bandit_750]

@@DrivewayDemons you a genius 👏

[@troys.5226]

Do they hang any lower than stock pipes? My challenger is lowered and I don’t want the bottom to scrape

[@wilheimreis8272]

Mine hang a bit.but mine not lowered.

[@JefeHones]

Sounds amazing but no sound clip of open headers!? I skipped a few parts but aren't you throwing codes now with no cats?

[@DrivewayDemons]

Hey J. No I didn't want to do that as it's not healthy. For me or the car haha. It does if you don't have a non fouler or simulator.

[@itsavibemotorsports-ivm126]

Did you get any O2 errors after this install?

[@wilheimreis8272]

I enjoy mine on my 1320 scatty,no mufflers and no resonators. The smell not so much. Going through tunnels the windows are up,cause it so damn loud on wot.😆🤘

[@nataliedeyton6829]

Thank man under my scat pack installing SW mids lol

[@DrivewayDemons]

Awesome! thanks Natalie!

[@MRRB172]

What if I striped the bolt. How can I remove it? I tried taking it off but it was really rusted. I used the female torque 8th but it was to rusted and that’s when I messed up

[@MBballer2]

ouch...

[@Playboyraj]

What the model number cuz the link don’t work no more

[@slomango7927]

Do you have a tune also???

[@DrivewayDemons]

Grocery Getter indeed. I put the cats back on tho.

[@slomango7927]

Driveway Demons too loud?

[@anthonydamico5830]

why put the cats back on? I'm about to order this same mid-pipe.

[@wjlowe111]

stainless works is the way to go!!

[@flacodominican9850]

need ur help i buy the o2 sensor spacers in amazon

[@Ebruhhk]

Hey guys i got a queston. Why not just hollow out ur cats. Cus after u do that, they will be just pipes. And isnt that the same as buying new one with no cats. Cant u just hollow them and use them instead of buying a new uncatted midpipe. Thanks

[@mcm95403]

Because then you have a big expansion chamber that disturbs the flow and doesn't do you much good. You COULD cut off the inlet pipe, destroy the honeycomb (which is FAR more difficult that you might think), then add a piece of straight pipe to avoid the expansion chamber effect, get it back on the car and then re-weld the inlet pipe. A lot of extra work though.

[@michaelgreen2962]

Looks and sounds good

[@DrivewayDemons]

Thanks Michael!

[@sunnyb707]

When going catless on the srt. Do you plug in the rear o2 or the front o2?

[@brandonscioneaux]

Plug in all 4. Double stack the 2 non-foulers on the 2 front 02 sensors.

[@og_blue3925]

Does it void ur warranty?

[@DrivewayDemons]

No it shouldn’t

[@ShogMan]

Anti-seize instead of WD-40 please

[@chapowiththesticks]

Bring back this hairstyle

[@DrivewayDemons]

I miss the hair but a lot of people disliked it.

[@polosrt2262]

What exactly would these be called online? I search jba catless down pipes and it says x pipe, y pipe, mid pipe. Thanks Bro

[@DrivewayDemons]

The links are in the info section Patrick. Everything you need 😀

[@polosrt2262]

Driveway Demons perfect still getting used to KZbin lol thank you! I appreciate it

[@EscobarMT]

Yo harry

[@OctaneRed392]

I’m thinking of doing this to my Daytona 392 gold content thanks for the info. I would’ve had my car on the ramp for three days lol 😂 without this info. #octanered392

[@SixTwoHemi]

Downpipes? Mid pipe*

[@srthatejeep]

Man you couldn't have started this in the morning or early afternoon 🤔

[@tonycolon67]

Man how do you afford a hellcat and the extra parts for it and all the expensive cameras and gear that you have on your other channel .... whatever it is share it with me bro!! good job living the dream

[@86HellCat831]

How are these compared to the stainless works?

[@DrivewayDemons]

They are great