Here's the first video where I show how to embed the FibaFuse drywall tape: kzbin.info/www/bejne/g3zHnX6diM-qgM0
@TreseMari3 жыл бұрын
This link doesn't work. Please post updated link. Thank you for your videos! They've helped me a lot, as this is the first time I'm doing this kind of work.
@danham33443 жыл бұрын
I was taught about the concave side on almost all mud knives 25 years ago. What I didn’t know was that I could use the non-concave side for feathering. I’ve been using the concave side only all this time for my DIY jobs. Sure appreciate your video as I’m starting to tape/mud my new 1,800sq/ft shop. 😃👍🏼💪🏼
@toddmoriarty974 жыл бұрын
I've been using my 12" knife for 16 years and didn't know there was a concave/convex side. Who knew?! Thanks Paul and KZbin.
@bitTorrenter2 жыл бұрын
Can I ask you why you and others use such a wide blade when joints and tape are no where near that size? I noticed that father has a 8" Marshalltown, but after reading I've heard 10" is a popular size due to it being easier to handle than a 12" blade.
@ScullyPop4 жыл бұрын
The channel has so many great aspects. I've learned a ton from Paul. He comes highly recommended.
@PaulPeck4 жыл бұрын
Right on Scully!💥👊🏻 I really appreciate your support my friend!😎 -Paul
@ConstructionKronies4 жыл бұрын
Right on Scully's House! Man I hope your doing well, am I missing your streams? I don;t think I have got a notification in a while. Your a solid dude brother! 👊🔥💨💨💨
@DutyRon4 жыл бұрын
This guy makes it look simple folks watch and learn from one of the best!
@allhartfidelity4 жыл бұрын
I did notice the concave side, Did my first mud job last week. I did not do the tape though, it was a new constuction house and they taped it. But not a second coat, and did not go over the tape. I jist wanted it covered. The butts were a PITA so left them. Tape job sucked as they likely figured it was a garage and would never be painted. I jist diddnt want my paint to mess with the exposed tape... Just a nitpick, if there is a concave side to the knife (there is) then there is no flat side. That would be a convex side ;) Thanks for the tips
@PaulPeck4 жыл бұрын
Haha Charles...😂 You’re absolutely right. It was just a way of explaining the concave side to the other (flat) side.😇 it really isn’t flat. Although when pressure is applied there is more of a flat surface then not.👍🏻 Thanks so much for watching and commenting my friend! -Paul
@allhartfidelity4 жыл бұрын
@@PaulPeck I used the same side for applying and pulling it tight though. I will use both sides like you did from now on. Do you prefer the pan over a hawk?
@LayneCocaine3 жыл бұрын
Concave side pushed flat on the flats, bow of the concave side to the wall on the butts, always came out best that way
@James-bv4nu2 жыл бұрын
Superb video! You explain the what, why, and how. Very clearly. From DIYers like myself, thank you.
@kathyfromtexas86134 жыл бұрын
I asked my husband if he knew about the concave side, and he didn't. I don't mind helping with painting projects around here, so I watch your channel all the time for your tips. (PS Are you so used to the work that you aren't aching at night ?? We sure are !!). Thanks, Paul
@PaulPeck4 жыл бұрын
That’s awesome Kathy!🔥 I really appreciate your feedback! 👍🏻 Haha.. I do get a little sore every once in a while!😇 -Paul
@vtec2194 жыл бұрын
I didn’t know the difference between the two sides. Thanks for the tip. Big difference on finish.
@dad1432 Жыл бұрын
I knew about the two sides from other videos, but I think you're the first to show using the convex side to smooth.
@KGrant-ty3oy Жыл бұрын
So many new knives seem to be flat. How would you/can you add a bend to it yourself? Thanks!
@jeannemyers489 Жыл бұрын
Never knew about the concave side verses the convex side. Thank you so much Paul! Now I can properly finish my bedroom. 🤩
@jeffcook8635 Жыл бұрын
Is it pretty standard when you buy a knife at Lowe’s and Home Depot for the sticker to be on the concave side?
@chaddaddy94414 жыл бұрын
So you don't sand before texturing? I have been but I'd love to skip that. Most of my jobs are knock down. Thank you so much for posting these. It makes me a better asset.
@PaulPeck4 жыл бұрын
Hey Chad!💥👊🏻 I don’t sand because all my edges are pulled super tight. I will go around with my 6” taping knife and scrape any ridges or hi spots. I also carry a pencil around and mark any areas I see that needs mud. The I’ll go around one more time and hit those areas super tight again.👍🏻 Thank you so much for watching and commenting!😎 -Paul
@sherryspectre2174 жыл бұрын
#DrywallTube
@rickeykeeton4770 Жыл бұрын
I think I might apply too much pressure in the concave side, if my knives have one. Seems like the knives being do flexible, it is easy to apply too much pressure.
@thriftyninja00752 жыл бұрын
I am just trying to do a few joints in my house. I bought a 12” knife. When I stand the knife up on its edge on a flat surface the middle is not touching. Is it supposed to be like that? It’s not exactly what you are talking about here. I just feel like this would cause the edges to dig in really bad.
@rickeykeeton4770 Жыл бұрын
I saw in the ither video you mentioned people sealing the drywall before mudding. I have never done that except for once when I applied popcorn. That being said and with possible problems being moisture from the pool, would have been a good idea to seal this ceiling? If not, what is to prevent the same thing happening again?
@mdavid71493 жыл бұрын
It's a feeling and nothing else. Not to take away from ANY of this. I'm a baby in this world of contractordom. You feel the concave and it does flow but your hands will flow as well. The blade; even against corners and corner beads will flow as long as this process you're showing us is followed and your keep your hands with the curve
@tcc8823 жыл бұрын
How are you getting mud on only part of the knife and how are you sliding the knife to prevent the mud from dripping off the side and falling on you
@tallmex963 жыл бұрын
Honestly the only video I've found for this exactly. sparky by trade, decided to take the time and get into carpentry which just like electrical has many aspects, ive taped before but starting tommorow its going to be more serious (for me) than juts patching holes i make to run pipe lol thank you!
@johngannon13492 ай бұрын
Hi Paul I'd like to see how you finish your butt joints into factory bevel edge thanks.
@johnjohn-ne8fw2 жыл бұрын
Did not know about the concave side. thx for the info. I'm committed now to subscribe 👍
@aaronjacobson69578 ай бұрын
Man,I can always tell a real pro cuz you guys make that look so so so damn easy. Thanks for your channel boss. I need all three help I can get when it comes to mudding so I don't have to sand much... Or none at all preferably... Maybe someday...
@leeb.71887 ай бұрын
I heard about concave/convex blades and looked at mine, but they look the same, completely flat. Maybe it’s my eyes, or the brand I use (Quinn, from Harbor Freight.)
@UrbanVanlife4 жыл бұрын
i dont use any cos im not good like you , but that wire was annoying me as well lol , nice work paul ,
@PaulPeck4 жыл бұрын
Haha... I kow right! You know all about annoying wires lately I'm sure Neil. Thanks for stopping by bro! -Paul
@vertebrate7464 жыл бұрын
I love your videos which have been very helpful. Thank you. Do the same rules apply if you are doing a skim coat over sheetrock on a ceiling repair? Thanks again.
@inspiredbythekingYT2 жыл бұрын
Depends on the patch. If the whole patch needs mud your gunna use the non concave side applying pressure on one side and working all the way out so you don't have a line
@martinm21784 жыл бұрын
Not aware of that feature, Paul. Thanks for pointing that out. Just got some fibafuse. Can't wait to try it out. Thanks for the tip.
@PaulPeck4 жыл бұрын
That’s awesome Martin!💥👊🏻 Let me know how you like the FibaFuse man!😎 -Paul
@Janton_12 жыл бұрын
Im new to this and just looked at my 12 inch and. its completely flat, who makes a concave 12 inch? Thank you for such a great video and lesson.Could I bend it and make a concave side?
@Jdww893 жыл бұрын
So use the non-sticker side to apply mud and the sticker side to take the mud off/ smooth out
@sherryspectre2174 жыл бұрын
I know about the concave side. Use it occasionally if it calls for it. Otherwise, the side that has my groove....
@PaulPeck4 жыл бұрын
That’s how I roll to Sherry!💥👊🏻 Thanks for watching and commenting my friend! -Paul
@yjohn52903 жыл бұрын
Great tip. I never knew.... that will save me some time. Thanks for sharing. Great channel
@PaulPeck3 жыл бұрын
That’s awesome Y John!👍🏻 I appreciate that man!😎 -Paul
@stephenjhayes14 жыл бұрын
Wow! That's great info! I always use the flat side but this makes so much more sense! I've used A curved trowel occasionally and this looks like the same concept.. smh that i didn't get it till now! Definitely gonna use it that way next time!! thanks Paul!!😊
@PaulPeck4 жыл бұрын
Glad it was helpful! Thanks so much for watching and commenting! -Paul
@KevinDiaz-kz9lt3 жыл бұрын
How do you reuse and clean your drop cloths for drywall work? Mine always have clumps of mud from drops and get super dusty
@malcolmgary10862 жыл бұрын
DANG!!! I checked my 12'' knife, and it does have a concave side (on the lable side too). Thank you for the tip... I subscribed to your channel.
@JoshB883 жыл бұрын
Watching this video was like hearing finger nails on a chalk board
@AnniePilatesPhysicalTherapist4 жыл бұрын
Another clean and precise work
@PaulPeck4 жыл бұрын
Hey there Annie!✌🏻 Thanks so much for watching and commenting my friend!😎 -Paul
@pilotmedic2 жыл бұрын
A lot of people don't explain both side. Thanks
@josephine26392 жыл бұрын
Just watched your video, i’m in Scotland, i just think its a bit quicker with two trowelled on coats with 11 & 14 inch trowels no edges n a light sand to finish, each to their own, but your blades are good, what make are they?
@Driver7323 жыл бұрын
Saw another video yesterday that mentioned 4 inch taping knives have this too and wanted more info on that. This video was helpful, thanks!
@lestalkmorebasss5 ай бұрын
They all have some degree of concavity….. Even a 2” knife
@Scrapienza Жыл бұрын
I’m a finisher and I’m ngl, I’ve never seen anyone use green lid all purpose for coating. That’s normally just a taping mud. It’s also a lot harder to sand because of the glue that’s in that mud. I tape with the all the all purpose and coat with the plus 3. IMO the plus 3 is a lot smoother and twice as easy to sand
@michaelwellner81512 жыл бұрын
I didn’t know that ‘awesome to know “please keep me posted I do some drywall and always want to get better. Are all knives con caved? Or what is the best brand to buy?
@ConstructionKronies4 жыл бұрын
Alright man I think I got it Paul, thank for these vids man I really appreciate it! 🔥👾👊
@fraseramos40292 жыл бұрын
What taping knife is this? Pretty sure my marshalltown doesn’t have a contoured side
@johnsayman22714 жыл бұрын
Your experience is showing, didn't have KZbin when I started this trade
@harperchalmers11822 жыл бұрын
Many newer big box store drywall knives are straight... without a concave side. My 45 year old Red Devil (with a wooden handle!) does! 🤗
@inkstain71937 ай бұрын
I haven’t seen a straight one.
@robsand80373 жыл бұрын
I never connected the sticker and the concave. Thanks
@AAPHomestead4 жыл бұрын
Another awesome Tip from The Pro👊🏻💥BAM
@PaulPeck4 жыл бұрын
I appreciate that brother!💥👊🏻 I hope you and your family are doing well man!🙏 Thanks so much for watching and commenting! 😎 -Paul
@gladdementia2 жыл бұрын
Um... I think I might have once thought the knife was bent. I tried to straighten it. Thank you.
@donaldtobin2354 жыл бұрын
Never look at the knife, excellent tip for today. I will be putting it to use the next time I drywall
@PaulPeck4 жыл бұрын
Right on Donald!💥👊🏻 Let me know how it goes. I really appreciate you watching and commenting my friend!😎 -Paul
@huejanus55053 жыл бұрын
Didn’t know about this feature, but i usually use my 12” curved trowel for the big coat.
@markwigley91854 жыл бұрын
I knew about the differing sides, but only used the non-concave side before. I was conditioned to do so. But will definitely try your method
@PaulPeck4 жыл бұрын
That’s awesome Mark!👍🏻 Let me know how it works out for you. Thanks so much for watching and commenting!😎 -Paul
@leonelhurtado90902 жыл бұрын
@@PaulPeck pp Moo mop la la my mi
@billyholt2270 Жыл бұрын
Did not know about the concave side
@nicholasregich78362 жыл бұрын
I’ve been a taper for 8 years now and everyone that I know around here already knew about it and we use both side. And not sure if you were doubling (2nd coat) or what but looks way different then what we’re used to lmao and get a hawk and trowel like a real taper
@CraftedbyMonnowLane3 жыл бұрын
Looking forward to watching your videos! DutyRon sent me over to say hi! He has some very good things to say about you!!! :)
@SuzyTopAgent4 жыл бұрын
Such a smooth and sleek job! Years of experience pays off 👍 #DrywallTube
@PaulPeck4 жыл бұрын
I really appreciate the support Suzy!💥👊🏻 Thanks so much for watching and commenting my friend!😎 -Paul
@micheleringrose40334 жыл бұрын
Thanks, Paul, very helpful as always! 👏👏 Noticed the concave side but did not realize how useful it could be, just a DIY’r here!
@PaulPeck4 жыл бұрын
That’s awesome Michele!💥👊🏻 Thank you so much for watching and subscribing my friend!😎 -Paul
@Jdww893 жыл бұрын
Is that the same with all knife lengths or just the 12
@sprayaholic4 жыл бұрын
Nice work buddy
@PaulPeck4 жыл бұрын
Right on man!💥👊🏻 Thanks so much for stopping by bro!😎 -Paul
@elvisvelez6609 Жыл бұрын
The funny thing is that I have the same exact knife but the sticker is on the other side or the conclave side. So if your watching this video and asking yourself why it’s not working the same then check what side your sticker is on.
@bonnivilleblackcherry97452 жыл бұрын
Not one of my knives are concaved. Marshalltowns, Level 5's, tape tech and kraft. Well dewalt too but they are really level 5.
@dscrive4 жыл бұрын
well darn. I never noticed, and I've gone through about 8 or 9 gallons of premix joint compound. thankfully pretty much all the work I was doing was repair work, so not knowing about the concave isn't such a stinker.
@PaulPeck4 жыл бұрын
Awesome man!👍🏻 Thanks so much for watching and commenting!😎 -Paul
@petethehandyman91854 жыл бұрын
You just keep teaching me something new!
@PaulPeck4 жыл бұрын
That’s awesome Pete!💥👊🏻 I really appreciate your feedback! Thanks so much for watching and commenting my friend!😎 -Paul
@Tierone13372 жыл бұрын
You. Took all the mud back off
@flowman7774 жыл бұрын
Nice job thank you..
@PaulPeck4 жыл бұрын
Right on flowman!💥👊🏻 Thanks so much for watching and commenting man!💥 -Paul
@ericamundson47002 жыл бұрын
the concave side does not the sticker side! it can be bent either way. I prefer a flat knife because then I can use either side and get the same results. I don't want to think about which way the knife is bent because this is distracting and would slow me down. I have 15 years experience is the finishing business
@vianalo95914 жыл бұрын
I really like your work..you have a amzing knife..
@PaulPeck4 жыл бұрын
Why thank you Mary!👍🏻😎
@offthecouch19992 жыл бұрын
I literally didn't notice
@michaelcarson48873 жыл бұрын
I was shown to use both because I aprentice under two different companies.
@cwrowe4 жыл бұрын
I had heard about it...however I have always just concentrated on finger placement? Mmmmmm
@PaulPeck4 жыл бұрын
Hey there Cw!💥👊🏻 I hear ya man! It is perfect for diyers on the factory joints though. Thanks for stopping by bro!😎 -Paul
@Nazgrok4 жыл бұрын
Mind blown.
@rogelioybarra40684 жыл бұрын
I knew that all taping knives have a concave side.. but i only use the other side to smooth
@PaulPeck4 жыл бұрын
I hear ya Rogelio!💥👍🏻 Thanks for watching bro! -Paul
@rogelioybarra40684 жыл бұрын
Paul Peck DrywallTube what would u use the other side for besides feathering a joint
@marshallwelchel72183 жыл бұрын
I've been doping for 45 years & I can show you alot better way than what your doing! Your working to hard...
@k.a.haugen36804 жыл бұрын
Damn.. forgot about that
@panormus0744 жыл бұрын
Complimenti, ottimo lavoro.
@PaulPeck4 жыл бұрын
Thanks bro!💥🔥
@k.a.haugen36804 жыл бұрын
Will remember for next time... and when sticker goes.. will put tape
@PaulPeck4 жыл бұрын
Right on K.A.!💥👊🏻😎
@terrywilliams52853 жыл бұрын
If you look at the handle of the knife one side should be smooth and the other side should have a logo on it thus eliminating the need to mark it to distinguish one side from the other
@losmoore33582 жыл бұрын
My knife kept making lines in middle. I cleaned it, so this concave could be the problem.
@PaulPeck2 жыл бұрын
Yes that could do it for sure Los.👍🏻 -Paul
@losmoore33582 жыл бұрын
@@PaulPeck thank u
@andersonsidney693 жыл бұрын
never knew that about the knife
@mdavid71493 жыл бұрын
Ugh I love my job 🤦🤦🤦😄
@loan64896 ай бұрын
Top ❤
@EdgeLord-js4vf2 жыл бұрын
I use the concave side 99% of the time
@xephael34854 жыл бұрын
Why did you put down plastic? Your work is so perfect you're not getting anything on the floor 😂
@mrtv7774 жыл бұрын
It reassures the customer you care about their property. 😀
@micheleringrose40334 жыл бұрын
Watch closely, he did drop a few blobs! 😁 Still a very helpful video! 👏 The plastic is an inexpensive, yet professional, touch.
@PaulPeck4 жыл бұрын
@xephael 😂 Thanks for stopping by bro!💥👊🏻 -Paul
@PaulPeck4 жыл бұрын
So true @mrtv77. I always try and show my customers that I respect and pay special attention to protecting their things. Actually, it’s one of my selling points when I go and do the initial estimate on a project.👍🏻 Thanks for watching and commenting! 😎 -Paul
@PaulPeck4 жыл бұрын
Haha @Michele Ringrose...😂 Yes covering and protecting makes a job go so much smoother! The customers happy and I’m happy! 💰 Thanks so much for watching and commenting! -Paul
@chrisagnew10473 жыл бұрын
When you want to learn how to do it right let me know been doing it 40 years and you take two God damn long