I had to throwaway my first one and buy another one lol 😂
@Raahymm2 ай бұрын
Same because it was to hard to assemble
@Breadcatlol69Ай бұрын
THX IT WORKS SOO WELL
@J.KINGTOONZАй бұрын
@@Breadcatlol69 I'm glad you got yours together 💪
@BrianAndrews-uh9ws3 ай бұрын
I cant connect the chest to the mid part it keeps falling off
@J.KINGTOONZ3 ай бұрын
Did you use the longest hook joint in the abdomen section, mine also kept falling off because the chest cover pinches against the abdominal section which prevents a lot of back and forward motion, so it does tend to pop off that's if you move it too much over a certain point. So you have to move the hip section if you want a more bent pose.
@OfficialThatTamGuy2 ай бұрын
me too
@rellsmooth12432 ай бұрын
Some come defective. I bought 2 so far and the first one came without a thigh bone and a short hook joint. That's why it pops off.
@abeeryasin18642 ай бұрын
Me too
@TKEDEADLYАй бұрын
Me to
@Raptor_TamerАй бұрын
Thank you so much. This really helped me.😄
@J.KINGTOONZАй бұрын
@@Raptor_Tamer You're welcome😉
@Twiddlefinger129 күн бұрын
Thanks for the guide
@J.KINGTOONZ28 күн бұрын
You're welcome🙂
@yazminvilla1835Ай бұрын
!! I just need the legs and hands but you got my other piece together !! I’ll be back tomorrow lol
@J.KINGTOONZАй бұрын
@@yazminvilla1835 Haha, hopefully the video somewhat helped 😅🙈
@dwayneph6327Ай бұрын
thx it helps me aot it works so well
@J.KINGTOONZАй бұрын
@@dwayneph6327 I'm glad you got it to work👍
@dafuqdoon-4 ай бұрын
this video helped me alot i had to make 3
@J.KINGTOONZ4 ай бұрын
Damn 3, that must of taken long to connect all those parts together 💀
@Veshremy56873 ай бұрын
Oh yea I have 6 bro 😂💀
@HasnaRimi3 ай бұрын
Yo i have a problem with the knee part what do i do
@J.KINGTOONZ3 ай бұрын
Are you talking about the knee cap?
@HasnaRimi3 ай бұрын
@@J.KINGTOONZ ye and the shoulder cap it doesnt fit allat
@J.KINGTOONZ3 ай бұрын
@@HasnaRimi Did you put it on the right way? Try straighten the leg and gently press against a table to connect the knee cap to the leg, there should be a small protruding piece that it clips onto.
@HasnaRimi3 ай бұрын
@@J.KINGTOONZthe knee part fitted in, Thanks!
@Vuxsgaming144 ай бұрын
I had so many problems of mine i had to throw some peices just to connect a joint
@J.KINGTOONZ4 ай бұрын
😂 I feel the frustration
@jordanchristopher32444 ай бұрын
Same bro it was so hard for me to put the arms on practically threw it
@J.KINGTOONZ4 ай бұрын
@@jordanchristopher3244 😱 I hope its okay now😂
@AbramBarraza-jw4cu3 ай бұрын
This is almost as bad as Lego
@pace4745Ай бұрын
Thank you so much
@J.KINGTOONZАй бұрын
@@pace4745 You're welcome 😁
@bentley12785 сағат бұрын
11:17
@gracielaplascencia2557Ай бұрын
You Have To The click
@gracielaplascencia2557Ай бұрын
😊
@J.KINGTOONZАй бұрын
🤔
@monicat67973 ай бұрын
THIS HELPED ME OUT ALOT! I just 3d printed the skeletal structure of it
@J.KINGTOONZ3 ай бұрын
That's good to hear and nice man, I wish I had a 3d printer 😢
@monicat67973 ай бұрын
@@J.KINGTOONZ GET ONE BRO!! you can get a good ender printer for like a 100 bucks which is pretty cheap considering the other prices for other printers
@monicat67973 ай бұрын
@@J.KINGTOONZ if you can afford a printer and a couple spools of filament, buy one! don't ya remember that old saying? when jobs give you money, buy a 3d printer!
@J.KINGTOONZ3 ай бұрын
@@monicat6797 That's the first time I heard that🤣
@TmntkingАй бұрын
When working with ghe crotch i can't connect it when it looks like i did its not all the way up and i 3d printed one
@J.KINGTOONZАй бұрын
When you connect it to the torso?
@jhoorlino53302 ай бұрын
The leg is too hard to assemble it kep falin
@J.KINGTOONZ2 ай бұрын
Yeh got to apply some pressure so it can click in, like against a table or dip the covering part in some lukewarm water and gentle push it in. It was difficult to put the legs together because of the cheap one I got.
@jhoorlino53302 ай бұрын
Damn really?
@J.KINGTOONZ2 ай бұрын
@@jhoorlino5330 yes hot water expand plastic and makes it softer to take apart and put together 👍
@_A_q_u_a_4 ай бұрын
3d printing them bigger and then assembeling them ist so much easier
@J.KINGTOONZ4 ай бұрын
True and less likely to break.
@wallfebox4 ай бұрын
4:52
@Dahzgtau9 күн бұрын
2:55 the ribcage on mine has a hole but the rib doesnt, what do i do
@J.KINGTOONZ8 күн бұрын
The holes at the back doesn't matter, it won't affect the figures function. I think it was just a design to show the front and back of the piece.
@diefetusАй бұрын
The head id too hard to assemble it keeps falling
@JuliusDiaz-po5kdАй бұрын
Same
@JuliusDiaz-po5kdАй бұрын
5:08 how do you do this
@J.KINGTOONZАй бұрын
Turn the black joint to the side and push it in and use a small tweezers to push it in firmly.
@AshirSohail-u4nАй бұрын
my hands cant move and they break easily also the same with the legs and tip?
@beambastic3711Ай бұрын
just try to make them move then there will be a crack sound
@AshirSohail-u4nАй бұрын
@@beambastic3711 k ty
@IsaAlbaloushiАй бұрын
I y do some of the prices keep sliding off when I attach them
@J.KINGTOONZАй бұрын
Maybe they too loose and need to be more rigid, try adding a small layer of super glue around the ball joint.
@riddhimahida6701Ай бұрын
The knee won’t connect
@J.KINGTOONZАй бұрын
You gotta press hard sometimes, preferably against a desk.
@darlewis1759Ай бұрын
Jeez i got ming of temu and it was not easy
@J.KINGTOONZАй бұрын
@@darlewis1759 haha same🙈
@edwardnellis2 ай бұрын
I DID IT!!
@J.KINGTOONZ2 ай бұрын
WAHOO! Gratz man🎉
@edwardnellis2 ай бұрын
Ty
@FrenkJanse3 ай бұрын
Now record one with focus on the parts ......
@AshirSohail-u4nАй бұрын
I MADE MY SECOND ONE :D 3 MORE TO GO
@TheSpecterXDАй бұрын
I lost a piece and I couldn't make it
@J.KINGTOONZАй бұрын
Goodluck finding the missing "one piece"
@TheSpecterXDАй бұрын
Thx...
@Dethtaild232 ай бұрын
Really help the assembly guide was really confusing
@J.KINGTOONZ2 ай бұрын
I'm confused to what you said, did the guide confuse you?🙈
@saffy630Ай бұрын
the m shape isnt fitting in the leg?
@J.KINGTOONZАй бұрын
@@saffy630 make sure everything facing the right way, you want the m shape to face the back of the leg so the middle part of the m is facing the front for the knee cap.
@Dezbisp3 ай бұрын
This helped me so much
@J.KINGTOONZ3 ай бұрын
I'm glad 👍
@rellsmooth12432 ай бұрын
Same
@user-yv5br7vl6q4 ай бұрын
For me the little parts are the most hardest part to put on probably going to take a other 3 hours
@J.KINGTOONZ4 ай бұрын
Goodluck! 🙏
@eyasahmad54162 ай бұрын
I need to connect all of them I mean all of the colors blue red everything
@J.KINGTOONZ2 ай бұрын
Nice! You have a variety of different ones, send me some haha
@Michelle_23147_hiАй бұрын
What is the name of the scissors tho
@J.KINGTOONZАй бұрын
Haha it's just really sharp kitchen scissors that I had, I don't know the name. Sorry 🙈
@TCJ-12342 ай бұрын
i have to build 15 of them took me 2 hours to make
@J.KINGTOONZ2 ай бұрын
Damn that's fast!
@Squ3aky-YT2 ай бұрын
Which way do I put on the neck piece it’s hard wondering how I put it on
@J.KINGTOONZ2 ай бұрын
It doesn't matter which way because they both the same length 😂 but you want the side with the point in the middle facing towards the back, so you can add the neck cover onto it.
@Squ3aky-YT2 ай бұрын
@@J.KINGTOONZok tysm I just finished it this video is amazing you deserve a like and sub
@J.KINGTOONZ2 ай бұрын
@@Squ3aky-YT Thanks man, I appreciate the support ❤️
@Squ3aky-YT2 ай бұрын
@@J.KINGTOONZthis vid is so helpful I already finished 4
@J.KINGTOONZ2 ай бұрын
@@Squ3aky-YT wow you got 4, you should try make a stop motion with them👌
@grefaldekarenp.36543 күн бұрын
bro i used my hands to take off the parts before assembling it💀💀
@J.KINGTOONZ19 сағат бұрын
Damn you got some strong fingers
@referee19844 ай бұрын
Mine was having a really big problem Like the body dont comnect or it doesn't fit through cus its too big
@J.KINGTOONZ4 ай бұрын
Mine was big too. I had to heat it up a little and squeeze it a bit with pliers but not too much else you might break it. Then I pressed down against my table and it eventually popped in place.
@demonvoid47464 күн бұрын
The arms cant move... It only goes straight instead of other directions
@J.KINGTOONZ19 сағат бұрын
Did you put the joints the right way?
@vasilijekrstic95024 ай бұрын
Had to glue some of my dummy 13 cause some of the joints didnt want to connect, i also have a fake one
@J.KINGTOONZ4 ай бұрын
Yeh it's not as easy as some videos make it to believe 😂
@Skittlegamies2 ай бұрын
The hard part is the head since it is hard to put in the lego like hand inside the square 😑😑😑
@cateriksson34192 ай бұрын
Fr
@J.KINGTOONZ2 ай бұрын
😂
@LarryBarnett-z3kАй бұрын
I just ordered a lot of similar ones, so wish me luck
@Blue_sans1Ай бұрын
I can't connect the head with the joint
@J.KINGTOONZАй бұрын
Try use small tweezers fit the joint inside the head, then push down using the back end of the tweezers. It should fit in nicely unless your figure isn't well made, like mine.
@Blue_sans1Ай бұрын
@@J.KINGTOONZ ty
@Blue_sans1Ай бұрын
@@J.KINGTOONZ where you buy you figure I wanna buy other
@J.KINGTOONZАй бұрын
@@Blue_sans1 from Temu😂
@Kay4739_3 ай бұрын
Bro the number 3 looking attachment is not budging to the leg
@J.KINGTOONZ3 ай бұрын
Yeah you got to push against a table or something, like I did with the back of my piliers but also not to break it at the same time xD. Make sure the 3 is facing the right way, you want the mid of the 3 facing outward so you can connect the knee covering to it later.
@SansakarinАй бұрын
can i ask some questions about this
@J.KINGTOONZАй бұрын
What are your questions?
@Andrei-k7z5 ай бұрын
Am having trouble connecting the first one
@J.KINGTOONZ5 ай бұрын
Yes, it's not easy if you get a knock off like mine, the joints are rigid and not very smooth to slide in each other. They can get stiff and sticky, you might need a little force to combined them but be careful not to push to hard on the small edges because they can break, like I did to mine. I super glued that piece that broke and its not noticeable unless I actually point it out😂
@danielapociumbeanu34064 ай бұрын
It took me days to assemble like im still working on it😂😂😂😂
@J.KINGTOONZ4 ай бұрын
@@danielapociumbeanu3406 Damn..that's crazy 😂 but you will eventually get there XD. I hope 🤣
@Veshremy56873 ай бұрын
Me too
@vinceveloce98974 ай бұрын
Thanks, it help me out a lot.
@J.KINGTOONZ4 ай бұрын
I'm glad it helped someone😁
@Guesty_AnimationsOfficial4 ай бұрын
I GOT THE BLACK ONE 😢😢😢😢 I CANT FIND THE JOINTS 😭😭😭😭
@J.KINGTOONZ4 ай бұрын
I see what you did there😂 I hope you find them😅🙏
@vinceveloce98974 ай бұрын
Lol.
@sumreenabdullah49293 ай бұрын
I also got a black one but I first put all of them apart for the jointment of 3d print than I closely looked at all the peoces and focused alot. Took me like 1-2 hours to build
@vinceveloce98973 ай бұрын
@@sumreenabdullah4929 @Guesty_AnimationsOfficial joke was funnier.
@PabloYIPPEАй бұрын
4:00 it won’t let me do it
@J.KINGTOONZАй бұрын
Put it in hot water so it softens a little and then try connect it. The heat usually expands the clip joint.
@sherryanncabanes62673 ай бұрын
Thx bro
@arnelgutierezmedico94404 ай бұрын
I think it will be easy for me cause i'm a great builder of Lego🙃
@J.KINGTOONZ4 ай бұрын
Yes but Lego is made differently, you should give it a try. It's mainly trying to connect the pieces that don't fit nicely together, which is the main problem in this figure.
@JustKen2403 ай бұрын
The headpart don't fits on mine
@J.KINGTOONZ3 ай бұрын
Does it keep popping off?
@JustKen2403 ай бұрын
@@J.KINGTOONZ yes
@Andrei-k7z5 ай бұрын
So hard to assemble
@christiemelezah85123 ай бұрын
i don't get it on 15m 23s
@J.KINGTOONZ3 ай бұрын
You must slide the cover over the joint from the smaller side (joint section) not the hook part because its too large to get it over. If you unsure which way the cover must face, the colour parts of the cover must face the top and bottom, when you lay the black hook joint flat on the table. I hope my explanation made some sense.🙈
@nuruulhidayah40702 ай бұрын
How to do the headd
@J.KINGTOONZАй бұрын
Turn the black joint to the side and push it in and use a small tweezers to push it in firmly.
@sprouty_94 ай бұрын
Mine was too hard bcz the chest part doesn't fit 3:18
@J.KINGTOONZ4 ай бұрын
Yes it doesn't line up nicely with the back holes but try dipping it in lukewarm water(not boiling water) and then gently attaching the yellow to the black skeletal part, it wont completely fit perfectly but it will still function and fit better than before.
@OliverSmith-xl2ll2 ай бұрын
Why do they not send them assembled
@J.KINGTOONZ2 ай бұрын
Some do but you pay more haha and besides... you won't have the joy of assembling them yourself XDDD
@OliverSmith-xl2ll2 ай бұрын
Are the ones of Amazon good
@J.KINGTOONZ2 ай бұрын
@@OliverSmith-xl2ll I never boughr one from Amazon but they look overpriced xD, I got mine from Temu at a very low price, it was like R25, that's like $1.34
@AshirSohail-u4nАй бұрын
@@OliverSmith-xl2ll i bought a amazon one it broke easily if u want a amazon one u should buy it assembled
@sherwingonzales251723 күн бұрын
My son has broke her toy but he has a new one
@J.KINGTOONZ22 күн бұрын
Nice💪
@edwardnellis2 ай бұрын
Oh, and also I lost the knee piece on the concrete in a crack, but I’m glad that I have a gold one coming and I found the piece
@J.KINGTOONZ2 ай бұрын
So wait... its not in the crack anymore?🤣
@edwardnellis2 ай бұрын
No I found it
@Ryomen_Sukuna293520 күн бұрын
I waited 7 months for this and it came with missing pieces I HATE THIS CRAP
@J.KINGTOONZ19 күн бұрын
@@Ryomen_Sukuna2935 Damn 7 months!! That's insane 😱, I got mine in 2 weeks😅
@Ryomen_Sukuna293519 күн бұрын
@@J.KINGTOONZ it came witgout 5 peices
@relufa2 ай бұрын
bro my body middle center cant even click im crying rn cuz it’s supposed to be for my brother birthday
@J.KINGTOONZ2 ай бұрын
Click to which? The chest or to the hips? It's bad, mine didnt fit properly either.. Did you have the longest ball hook joint in the mid section. Try put the chest part in warm water for a little while and then try click it in, but be gentle.
@SigmaTrigga3 ай бұрын
My hip section is all busted and won’t clip in for anything
@J.KINGTOONZ3 ай бұрын
mmm that's strange but it generally doesn't clip in nicely either, try rotating the joints 180 and clip the hip covering on again so... maybe the one side doesn't clip properly to the other side.