Dyna Clutch Basket Rebuild pt.1

[@balmand4043]

Thanks for the video. Haven't touched my bikes in 4 years. (Pre-covid) Forgot alot!😂

[@walterhoward4646]

What kinda woodpecker hammer skills have you developed there young man ! smack the socket one sharp rap at a time !

[@trevorhalford8410]

... You almost lost me with that rubber mallet, then you pulled out that homemade thingamajig and completely redeemed the video! LMAO 😅 awesome job yo! 👍🏻👍🏻👍🏻 I make homemade tools from odd stuff like that when I'm working on stuff. I refuse to pay 300 bucks for a tool that's going to sit in my toolbox for most of it's existence. 😬

[@donaldducharme4100]

For ever loving god man get a 60 dollar press from harbor frieght or northern tool. Son i new when u didnt flip over the basket to get the clutchs out, this one was going to be fun. One more thing. Get a vise bud any man , trying to diy style guys best 2 investment after a tool box is a table vise, and press! Thanks carry on!

[@lonewolf2608]

A press would work alot better

[@ernestcopoulos2709]

I can't watch this hack anymore!

[@dormantmenace]

I perfure the freeze the hub heat the race with a hot socket trick

[@rahulkumar-lb6nl]

i hv harly bob 1600cc having some ENGINE noisePROBLEM while self BUTTON press so pls suggest which part i SHOULD change

[@finley614]

Compensator chain too tight and probably from automatic chain tensioner in primary. Does your noise happen after bike is warm and you go to restart? If so it’s what i said and probably also starter clutch going bad now due to the issue over over tightened chain

[@finley614]

Also stock compensator could be going bad also from over tightening of primary chain. I had same issues and I replaced the automatic chain tensioner with a Baker Attitude manual tensioner and a Baker Compensator plus primary chain and transmission mainshaft bearing and starter clutch. All because of Harleys flawed automatic chain tensioner which cause severe issues in primary

[@shimaze5479]

I was hoping you would separate all the clutch discs. I want to see what the spring plate looks like

[@cliffordbaker7830]

what was your problem to begin with? i am having terrible noise coming from the clutch area in the primary still. after i have replaced every bearing including main drive gear in the transmission. seems to worsen as i ride it longer. ride has been down over 2 months and still haven't pinned down the problem. hope you see this message soon.

[@unclemaxschopshopmax5844]

I was converting my bike to chain drive and when I noticed the teeth were stripped out on the basket. I had no problem or noise when riding my bike that indicated the problem. If you are having a terrible sounding rattle in your primary case, it might be the big spring disks on the motor shaft. They might be installed wrong. I made that mistake myself and it took me a while to figure it out.

[@samarmstrong6990]

you are beating on the back side of an already weak aluminum clutch basket. this can cause more problems than you already have. I get the idea but this could turn out very expensive. those stock clutch baskets are very weak.

[@JCcanU]

Back in 2000 I broke a clutch hub doing that I was cringing , the whole time 1300 bucks , beating on the main bearing is not good . the cage race can get knocked out of round and under torque it will blow . Been there . Now I go to the welding shop pay them 10 bucks to use the press . they like to watch me do my own work and they make money . I live in Rule MO I make a lot of my own tools to get by . just like your bolt press , but a shop press is the only way to go .

[@robertculbertson9741]

You should use the snap ring pliers correctly.

[@wcaniz]

excelente video , gracias

[@davidmcmahon5991]

Really get a Bering press man or Machine shop to press it out 🤔😎

[@roncarter445]

Holy s*** you never heard of a press

[@ska60te]

That's what I said too Ron Carter my goodness !

[@roncoburn7771]

Dam I have seen it all

[@MR-rb5fz]

Like a 🏈🐒

[@divine_swine9665]

This is exactly what my grandpa said to me when he watched me get the struggle bus wrenching on w/e. After I finished or got pissed, then he’d show me how to use the press. Good times

[@amberbali8881]

Painful to watch. Use a press.

[@DavidBloxsom]

Probably a good video - just couldn't get past the foul language in the crappy music.

[@matthewhalpin8351]

Everybody wants their fifteen minutes of fame even those who dont know realy what they are doing ...

[@divine_swine9665]

Yeah cause that’s exactly why dude put the vid on KZbin. 🤔