DYSON V10 - HOW TO FULLY DISMANTLE AND REASSEMBLE THE DIRECT DRIVE CLEANER HEAD

Рет қаралды 24,569

The Vacuum Doctor

Күн бұрын

Пікірлер: 65

@Michael-qg6dm Ай бұрын

This video has been super helpful. I would never have dared dismantling this part without your video. Huge thanks!!!

@TheVacuumDoc Ай бұрын

Welcome

@michealcamilleri4994 Ай бұрын

Thank you for the how-to. I got it apart easily enough. I got stuck with the wires. You are a needed little nook of the internet cheers mate.

@TheVacuumDoc Ай бұрын

Anything you need Dyson mate . Let me know I got you :)

@kevinobyrne5 2 ай бұрын

Thanks for making this! 👍 I was about to order a replacement head for €90, but instead got a part for €20 delivered. Took me only half an hour to replace the broken part 😊

@TheVacuumDoc 2 ай бұрын

You’re welcome

@xhelhor 3 ай бұрын

Your video saved me money on buying a new one. Thank you very much! I took it apart and cleaned it myself... Great!

@gavintobin4912 Ай бұрын

Thanks a million for such an informative video, only got caught out on some of the smaller screw sizes.

@TheJamLancaster 2 ай бұрын

Thanks so much. I’ve just replaced my cyclone neck, attaching it to the original brush head. I assumed this would be a quick 5 minute job, but how wrong I was! Your video was invaluable, thank you.

@TheVacuumDoc 2 ай бұрын

Great job :)

@agnieszkawright5932 6 ай бұрын

Thank you for the video, I fixed my Dyson thanks to you 👍

@TheVacuumDoc 6 ай бұрын

I’m glad!

@chencheninnz 7 ай бұрын

Your video has saved me $150 buck to buy a new one 😅. Thank you so much!

@TheVacuumDoc 7 ай бұрын

Glad to help

@brandonvansittert2200 4 ай бұрын

Successful repaired my cleaner head with a $20 amazon kit thank you!!!

@theresawitter8247 6 ай бұрын

Great video. Clear and precise 👍🏾

@sonicuno1 6 ай бұрын

Thank you very much. You helped me to not fry my brush motor with incorrect pin order. Just saved 100+ euros and produced less waste

@ShunsukeK1 7 ай бұрын

this is exactly what i wanted to disassemble, thank you so much !

@melmclean7738 6 ай бұрын

Hi helpful because I didn’t know where the other screws where and they were under the bloody red strip u pulled out near start. However u doing the stem first means much less pressure and minimal rush of breaking. The bottom of the head will drop out easily by itself if left until time to pull stem/neck apart. Top can still come up in the same steps as you have. Cheers for the head mate. Appreciated

@mld8 Ай бұрын

Thank you!! Needed to know how to get the electrical wire out. Annoying need a T8 screwdriver as only have T10 upwards 😞

@TheVacuumDoc Ай бұрын

You’re welcome

@youngsie1 3 ай бұрын

Great video. Thanks for taking the time to do this.

@TheVacuumDoc 3 ай бұрын

You’re welcome !

@lloydpape8732 5 ай бұрын

Fantastic, I could not have done it without your video, I think Dyson should have included Torx t8 screwdriver free with the vac and also details of what to do.🎉🍷

@TheVacuumDoc 5 ай бұрын

Glad it helped mate !

@MsCashFlow 5 ай бұрын

Hi there, how do you replace and where can you get a "Freehweel body" for the head, <a href="#" class="seekto" data-time="302">5:02</a> It just broke on mine

@TheVacuumDoc 5 ай бұрын

Hi there , you’ll have to look on eBay or from a local seller or repairer who sells that party . Can’t buy separately from big parties

@MsCashFlow 5 ай бұрын

@@TheVacuumDoc Thank you

@janieskelton-christian7652 5 ай бұрын

Hi. I borrowed my beasties Dyson and the entire round part at 5:02 you showed broke completely. I dk how but now the neck just flops over and not stand up. It's the plastic under and around the 2 circular sides. Is there a way to replace that whole part or do I need to find an entire head?

@jean-claudevacher6476 2 ай бұрын

Merci beaucoup !! la brosse de notre aspi Dyson ne tournait plus, le démontage m'a permis d'accéder aux fils reliant le moteur et de les changer ! 👍👍

@megamanmike81 7 ай бұрын

Huge help, much appreciated the video

@TheVacuumDoc 7 ай бұрын

Glad to help !

@Addzaye 4 ай бұрын

Thanks man, you helped a lot!

@shotbyarian 24 күн бұрын

the brush bar seems like i can change the brush strips inside, but i can't find a way to open it?

@TheVacuumDoc 24 күн бұрын

Does the brush bar have a screw inside it?

@shotbyarian 24 күн бұрын

@@TheVacuumDocyes but behind is a bearing and i can't seem to remove it or the cap, that's why i am asking

@shotbyarian 24 күн бұрын

@@TheVacuumDocfor me it seems stupid to replace the whole thing when all i need replaced is the black strip

@TheVacuumDoc 24 күн бұрын

You can’t replace it you’ll need to replace whole brush bar for that 1

@shotbyarian 16 күн бұрын

@@TheVacuumDoc i was able to remove the bearing, just needed a lot of force, now i inserted new strips, working

@ilmancio8336 6 ай бұрын

Thanks Man. This helped me a lot

@TheVacuumDoc 6 ай бұрын

All good brother

@KoinKollect 4 ай бұрын

Awesome video helped me with a repair

@TheVacuumDoc 4 ай бұрын

Awesome :)

@michaelandcaron 6 ай бұрын

In my Dyson the black wire was broken. Great video. Thanks

@TheVacuumDoc 6 ай бұрын

Usually from to much turning and rotating in the head and a wire would’ve came out a bit. Replace head. Thanks

@philipgregory506 4 ай бұрын

Unfortunately I've disconnected the wires from the motor but not sure of the polarity to put them back! On the motor there is one plain pin and one with a blue dot. I'm assuming white wire to blue dot, is that correct?

@TheVacuumDoc 4 ай бұрын

It’s tricky to put in. I’d suggest watching a video on KZbin first.

@philipgregory506 4 ай бұрын

I've sorted it out now, actually the black wire connects to the blue dot. My problem was the brush not rotating and thanks to this video I dismantled it and found the broken wire. Repaired with solder and managed to reassemble.

@5678ytube Ай бұрын

I mistakenly soaked the whole cleaner head underwater (not realising that there is a motor) Any suggestions?

@TheVacuumDoc Ай бұрын

Did you use it at all after cleaning it?

@martinsaunders2942 3 ай бұрын

The most impressive thing there…is that you did it all wearing gloves!

@finns27 9 ай бұрын

Great video. There is two different lengths of screws, if you told us which lengths went where would be a great help.

@TheVacuumDoc 9 ай бұрын

The screws don’t vary in size much but if you follow the video and don’t get your screws mixed up they will go back in to the same spot. I’ll make sure to point this out in future videos as well, thank you for your feedback!

@hazelmoss6310 8 ай бұрын

Roller is solid and wont turn even after cleaning.?

@onetimedon 7 ай бұрын

this was so helpfull

@TheVacuumDoc 7 ай бұрын

Great to hear!

@Kate-wh4us 6 ай бұрын

Thanks a lot! ❤

@marcosgp8424 Ай бұрын

Thanks..!!!😉

@rolandtam2973 2 ай бұрын

don't understand why Dyson make the design so complicated. For generic home appliance should be user friendly for routine maintenance. If my V10 out of order, I will consider another brand. Anyway, the battery pack is long life. Very good performance. Really very very good !!