Eachine TS832 TS835 & RC832 FPV Gear

[@DutchRC]

Allso the same as the Skyzone products I think? I was wondering what the diff between these 2 VTX's is (apart from the input voltage) I'd suggest using these VTX's at their lowest specified voltage by the way.. They won't get as warm & live a lot longer.. At their maximum voltage, they will fail after a while (ask me how I know that :P)

[@AndyRCchannel]

haha yes agreed

[@Raqtor96]

I bought the TS832 and so did my friend. We both have those artifacts / lines / noise .. Even without a quadcopter or anything else electrical running anywhere nearby. Also this transmitter is very noisy on other channels than the one selected and does interfere with other people flying FPV nearby. We found one channel that we were able to pick up on 8 different channels on the receiver :-) But we were easily able to find 2 channels that did work together and the lines/noise isn't that bad that you can't fly with it. Concerning running it on a 4S battery. You should keep it running for 10 minutes and then immediately check it's temperature. Then chose for yourself if you are comfortable with that in the long run.

[@AndyRCchannel]

flights with this aircraft are 15 mins at a time and no issues so far. but I am stepping it down now. thanks for the other Info

[@kamil13877]

Andy, will it be dectected by windows 10 as a normal webcam? Or does it need additional software?

[@justovelarde3456]

Excellent video. Congratulations friend. A question, what maximum distance can you reach? Maybe 1 km? Thank you.

[@stridermt2k]

I use an 832 TX on my WLToys V666, with CP antennas. I replaced the smaller FPV transmitter with this one on the lens-modded V666 camera. (channel 38 for the WLtoys receiver BTW) I use a smaller 7.4v 2s battery attached to the top of the quad to run the FPV system as I've found it to be the most effective way of eliminating electrical noise from the video. Filters have not helped much on my V666 and I also want to spare the flight battery. Even running at base voltage on a smaller battery the system works very well, and with CP antennas multipath interference is of course eliminated. Great stuff as usual, Andy!

[@AndyRCchannel]

that's good to know Michael. this quad setup is running a 4s however that can't stop me down stepping it to 7v. I might give it a try cheers. that's a nice setup for your v666!

[@stridermt2k]

+AndyRC Mine is merely a modified toy compared to your setup but it serves as a test bed and flies pretty good too. You are most gracious, thank you.

[@AndyRCchannel]

they are all toys really ;) i dont care what anyone says they are big boys toys ;)

[@hippopotamus86]

Try aiming your cloverleaf down instead of up, that way its always in line of sight. I have the same transmitter and not had problems as much as yours.

[@CrisisActorJonsiri]

if you use the balance port and an adapter that goes from 4 pin balance to jst, it will reduce interference.

[@TheDaniel366Cobra]

Greetings! Just got myself this set. Everything seems to be working alright, but the transmitter is running hot at 12 volts.After 3 minutes it is painful to the touch. Is it OK or should I rip the metal casing off and glue a nice radiator onto the power amplifier IC?

[@vjjames4567]

good thing I ran into this video Andy, I just found this transmitter in my hobby box, I am trying to get audio out of it but do not know how can you help. thanks

[@YevgenShevchenko]

These transmitter and receiver are neither Boscam nor Eachine. Manufacturer is unknown. Both transmitters are 400mW; 450mW on some channels.

[@AndyRCchannel]

everywhere sells them as boscam and being 600mw they are uber cheap and work nice for me. many products in this hobby are rebranded.

[@arnepetry]

you can also use immersion or flyingfolk antennas which are equal or even better, but I found the aomways to be very good value... btw: using better antennas did more to my range them the step from 200 to 600mw; 200mw with a good antenna gives at least double the range to 600mw with bad antenna...

[@AndyRCchannel]

yes definately makes a difference these were just antennas I had lying around. I need to upgrade

[@DrohneschweizCh]

what about only adding lc filter and not fpv voltage 12v regulator ? Do you think do you really need it ? Thanks for your videos !

[@hookabunny5030]

How do I get sound mine has a mic on it.. I have a 7 inch monitor with speakers and it's a stand alone monitor... Eachine

[@arborcam]

Novice question. If I have a Eachine 5802D dvr monitor (5.8ghz) and a Eachine TS 832 transmitter, do I also need a seperate receiver or is there a receiver built into the 5802 monitor?

[@iainknowles9008]

Is the picture quality and the artefacts that you saw in the video typical for most FPV setups in this price bracket (or the more expensive boscam versions). At this range I was expecting it to be artefact free.

[@AndyRCchannel]

+Iain Knowles its analogue so its never artifact free :)

[@adityamittal2253]

pls send the link of the site from which I can buy the 600TV line camera as used here

[@SmidFilip]

Did you run into the same issue with low voltage on power out of the TS835 ? I get 4.64v there.. is there a way to adjust it ?

[@kerryomo]

whether the device can transmit sound/audio ?

[@NathansVideos46]

Hey great video, I just have one question. You say your 4s is 16.6v. Is it not a lipo? because I thought lipo 4s were 14.8v

[@AndyRCchannel]

+NathansVideos46 they are 16V+ when fully charged

[@TheRealDylanFraser]

Dear rc model reviews I am looking to buy a RC quadcopter for my birthday I have looked at Hobbyking ready to fly quadcopter but I seen your video talking about how hobby king aren't always reliable so I was wondering if you could help me choose the parts to buy to make the quad copter the budget for the quadcopter is £120 and that will include everything apart from FPV Gear it will be my first time flying a proper hobby grade quadcopter but I know what I'm doing because I am well knowledged in quadcopters and I have flown cheaper quadcopters in the past thanks for the help.

[@AndyRCchannel]

+dylan fraser check out my video called build a cheap quadcopter. I did it for about 120 pounds

[@TheRealDylanFraser]

is it 250 size

[@AndyRCchannel]

no 450 size for 250 size check out rcmodelreviews build

[@oskarjennische2490]

i can use this one to my stock fat shark attitude v3s right? i am talking about ts832

[@ReallyHarrison]

Hi I think I might be making my own quad I have got a base f450, soldering stuff, electric tape, a electric dispersion board, motors props and esc, a transmitter and receiver all I need is a flight controller but I want to keep it on a budget, I want it to be simple and if there is a cheap one I may want to add GPs later in the year, thanks is there anything I'm missing apart from that

[@AndyRCchannel]

+ReallyHarrison yes you missed time and patience haha you need a lot of it in this hobby ;) good luck with the build! all the best

[@ReallyHarrison]

+AndyRC is there a cheap flight controller you can suggest

[@AndyRCchannel]

the CC3d is the cheapest. its used on the cheap quadcopter build check it out :) you cant add gps to a cheap board though and theres no alt hold either. to add gps you would have to go with the naze32 but be careful with that as it only has ppm input (all down one wire) other than that u are alooking at 80gbp for the cheapest GPS enabled flight controller

[@ReallyHarrison]

+AndyRC there is a apm 2.6 which is around £20 which has a gps input have you seen this,thanks for the reply

[@AndyRCchannel]

+ReallyHarrison yes I have one however support for APM has been discontinued so bare that in mind

[@Glenn.J]

Hi Andy, Did you manage to get the TS 835 working with 3S / 4S lipo? I recently got one from Banggood, plugged in everything, I am able to see the FR and CH digits on the VTX but no video output on any of the channels. I have tested this using my fatsharks and even a RC 305 VRX. The RX on the fatsharks are the BETA bands one ("Fat Shark Dominator 5.8GHz Receiver Module, BETA Bands") The seller sent me a second one as a replacement but I am seeing the same issue. I am wondering if I am missing out something critical. Thanks.

[@AndyRCchannel]

I had the same issue with my one. never got a picture from it and assumed it was defective

[@Glenn.J]

+AndyRC so what did you do? replacement?

[@AndyRCchannel]

no it was sent in for review so i left it. if you bought it off banggood send their customer service an email and they will refund you

[@Glenn.J]

+AndyRC ok thanks a lot. let me do that and try and investigate further with the unit when I get time.

[@AndyRCchannel]

let me know as id like to get to the bottom of why mine doesnt work too!

[@obinnaeke8067]

I'm buying the TS832, I don't need an extra lc filter then right?

[@AndyRCchannel]

u shouldn't do it depends if your system has much noise

[@obinnaeke8067]

ok, thanks. btw I am using one 5200mAh lipo. I just connect the vtx to the power module?

[@lolitechk]

hello andy...i havent seen new video about this quad...i know u r too busy with reviews etc. but i really loved this series...next video adding a gimbal w/ action camera maybe?

[@AndyRCchannel]

you are right i need to do an update on this one. i planned to add the storm 32 gimbal to it. but the hobby moved faster than i could attach it lol. wanna put it up against the phantom. cheers!

[@georgetheodosiou7850]

Hi, can you please tell me what is the voltage output for camera on the ts832 tx? I'm thinking to buy one to built a cheap fpv system.

[@blackterminal]

Seems it's 5v. Refuses to work on my 12v camera

[@analmasiroky]

do you recommend that vtx for 210 racing quad ? i know there lighter 40 ch vtx, but not sure about heat and stability issues

[@AndyRCchannel]

no i would go smaller than this for a 210 cheers

[@michi125125]

Hey Andy! :) I have this reciever it is not clone of boscam it is rebrand of boscam. It is huge difrence :P

[@AndyRCchannel]

I think you misunderstood . I use the words exact clone. same components, same everything so yes they are a rebrand

[@harrymoman2682]

Have you got a link to adding your osd Thanks great vid

[@juancarlosbarrera553]

With this transmitter I can transmit directly at the goggles?

[@AndyRCchannel]

yes u can thx

[@hawkeye312456]

can I use a 7.4volt battery 1000mah on the receiver?

[@PrathameshPatyeker]

Jamaine Davis yeah sure you can ..

[@lee_fpv]

the ts835 i can run it normaly with 3s correct??? or i need more s at baterry??

[@AndyRCchannel]

+George Papadopoulos u can run 3s fine yes

[@lee_fpv]

thanks man... im wating in a feew days to recive it... and i see your video and im asking becose of the voltage what you have told.. thanks..

[@AndyRCchannel]

u dont need to worry it will work good

[@cameronhill3329]

What's the output power for the ts835 ?

[@QuadcopterAnalyze1980]

Andy what dc power adaptor could i use for the reciever?

[@PrathameshPatyeker]

Shea300zxTT 10 v to 12v DC adapter you can use

[@LeonardoValente_]

Range ?

[@Ryan_Prewer]

Will any of these work with the Laser BGC Android RX? Sorry if it's a stupid question, I'm new to Fpv so finding it all a bit confusing 😓

[@AndyRCchannel]

+Ryan Prewer yes it will as long as you use the fatshark receiver module with them

[@Ryan_Prewer]

+AndyRC Thank you 😊 your channel is amazing btw and it's helped me out a lot, especially with this electrical side for people on a tight budget 😀

[@AndyRCchannel]

+Ryan Prewer no problem thanks for watching

[@gobiandreson3111]

My TS832 is heating what can I do ?

[@gobiandreson3111]

Pls help me!!!!!

[@revparsons3tl]

what is the output voltage from the tge transmitter to the camera

[@blackterminal]

5v

[@KypexHacking]

What are you use pal or ntsc?

[@viktorroyal8282]

It works both :)

[@fluxfpv]

4s is 16.8 volts. :)

[@AndyRCchannel]

I never charge to 4.2 volts so my 4s are all 16.6 volts I use nanotechs so 4.2 kills them

[@muh1h1]

+AndyRC You can put a normal diode in line to bring the voltage down ~700mv, which also protects it from being connected the wrong way :) I would really suggest that cheap (actually free, if you get the diode from the rectifier of a broken piece of electronic for example) mod, since you don't want your copter to suddently lose its video connection when you are least inticipating it!

[@muh1h1]

+muh1h1 OK should have watched all the way to the end :)

[@permapsy2020]

+AndyRC Andy what do you charge them up to? I got the same Hobbyking one you recommended.

[@AndyRCchannel]

+Perma Psy I do 4 volts per cell

[@Mooria]

what kind of battery do use for Boscam RC832?

[@AndyRCchannel]

+Mooria Devil any 12V will be fine (3s)

[@Mooria]

but i was wondering what connectors it shuld have, i only have the traxxas connector :D

[@AndyRCchannel]

it comes with one

[@Mooria]

Boscam RC832 comes with a battery? i asked the store but they dident know anything :/

[@AndyRCchannel]

+Mooria Devil no it comes with a cable to connect a battery too