Fast Etch: www.eastwood.com/rust-remover-eastwood-fast-etch.html?KZbin&+comparison+fast+etch Gel Dissolver: www.eastwood.com/rust-remover-eastwood-rust-dissolver.html?KZbin&+comparison+gel+dissolver Rust Converter: www.eastwood.com/eastwood-rust-converter.html?KZbin&+converter+gel+dissolver
@craigwiest7728 ай бұрын
Excellent comparison of these three products.
@T3glider8 ай бұрын
Fantastic video!
@eastwoodco8 ай бұрын
Glad you liked it!
@frankstehm22508 ай бұрын
Is the rust dissolver basically the same chemical as fast etch, but in gel form?
@levih.42526 ай бұрын
Eastwood, same question.... (not necessarily the same chemical but the same result?)
@diegosilang48238 ай бұрын
So far I find the fast etch to be very effective and it suffers virtually no flash rusting, the only side effect is you have to wipe out the excess before it get dry or it will leave gummy residue. Heavily rusted metal requires some wire brushing or these chemicals will not able to penetrate.
@sabbo688 ай бұрын
Will there be any other flavors in the future?
@ughievox25136 ай бұрын
Please tell us the active ingredients of the last two. Phosphoric acid was the fast etch. Then what are the next two? Is one of them Lye like found in RUST OUT?
@cjcarpenter83668 ай бұрын
Awesome video
@eastwoodco8 ай бұрын
Thanks!
@Mrsark59192 ай бұрын
Is this liquid version of rust converter good/ok to use on bare metal spots? The aerosol can says not to use on bare metal
@kanoahstevens6603Ай бұрын
Would it be good to use rust converter on inside of a truck frame and then go over with your Eastwood internal frame coating? Or should I just go through the inside of frame with internal frame coating alone?
@eastwoodcoАй бұрын
Do you have access to the inside of the frame? The benefit of internal frame coating is that it has a wand to get inside boxed frames. If you have an open c channel you have more options.
@kanoahstevens6603Ай бұрын
I don’t have access to wipe anything down but I have a spray gun with access rod that can spray rust converter in the frame if it would be better than the internal frame coating by itself? Can I use rust converter and the internal frame coating together? I have a boxed frame.
@eastwoodcoАй бұрын
Okay now we understand - yes you can double them up. Spray converter let it sit for 24 hours then top coat with encapsulator or internal frame coat.
@jimdrechsel36113 ай бұрын
If you use the rust converter can you go over with a different product if you are not satisfied like the remover or Fast Etch?
@eastwoodco2 ай бұрын
You could - more likely you would use converter, fast etch, or remover and then coat with encapsulator or move to epoxy primer.
@jimdrechsel36112 ай бұрын
@@eastwoodco my understanding is that the encapsulator is not meant for large panels like quarter panels. If you don’t get all the pinholes of rust and you apply epoxy primer will the epoxy prevent rust from popping through? It seems like the last insurance step would be a converter since a disolver may not get everything. I’m talking about a panel that can’t be blasted for fear of warping.
@eastwoodco2 ай бұрын
Okay now we understand. You could use use the converter and then spray fast etch across the panel as extra insurance. Check out the workflow we did on the mustang here at 4:17 : kzbin.info/www/bejne/qIuad2mdotJ7aqc
@jimdrechsel36112 ай бұрын
@@eastwoodco so would the fast etch begin to remove the areas where it turned black from the converter? Does epoxy primer seal any small rust pits or will it eventually come back through? It seems impossible to get all the rust. Are your epoxy primers high build?
@eastwoodco2 ай бұрын
We spoke with our engineering department and they said: For rust on large panel best method is DA/sanding with 80grit, thus leaving rust in valleys, sub scratches and pin holes. Blow off panel, apply fast etch. This is the best method for actually dissolving rust with diluted phosphoric acid. Apply to surface with rag or spray bottle, allow to sit 5 mins reapply until pin holes turn to dark spots (rust is now dissolved and chemical reaction leaves iron phosphate). Then apply epoxy primer. Rust convertor is used when panel can not be first abraded with 80 grit to remove corrosion (think recessed door jamb). rust convertor must be applied directly over rust not fast etch or any other product. Our epoxy's will have some build (OptiFlow has a decent amount) but for explicitly high build you would want to look at urethane or polyester High Build Primer.
@hpautostyle2 ай бұрын
Any rust removal spray that can be sprayed on and let dry?
@eastwoodcoАй бұрын
The rust converter will do what you're talking about. Or you can use rust encapsulator and top coat from there.
@iphanyeАй бұрын
Can i use this on my motorcycle exhaust?
@eastwoodcoАй бұрын
As long as it's not freshly running it will treat pitting that's common on exhausts. You'll still need to clean it off and then top coat with something to prevent the rust from coming back.
@user-tn1hk6zm2freedomАй бұрын
White vinegar is great for removing rust and it is cheap.
@DavidPlass6 ай бұрын
9:00 that's the thinnest gel I've ever seen!
@oOs4MzOo2 ай бұрын
Hey bro, i need some help, so i have water leak in my trunk, after i fix thr leak, i want to fix the the rust, what is the best way to do this? Should i use fast etch or rust converter, The rust seemed to be near seam sealer area
@eastwoodco2 ай бұрын
How deep is the rust? Fast etch is for light pitting/surface rust. Rust converter is for deeper issues.
@oOs4MzOo2 ай бұрын
@@eastwoodco hard to tell its between middle to deep rust, can i use fast etch first, then hit it with the rust converter after? I also came across the por-15 kit, any good?
@eastwoodco2 ай бұрын
Okay with that info we'd recommend wire brushing all the loose/bad stuff off and rust encapsulating the area, we have it in aerosol or brush able versions. www.eastwood.com/eastwood-rust-encapsulator-plus.html
@cougarslayer914 ай бұрын
is it ok to spray eastwood fast etch near hydraulic hose?
@eastwoodco4 ай бұрын
You will probably want to tape it off, and wipe any excess spray off with pre-painting prep to neutralize it.
@calebtrussell85244 ай бұрын
What’s the stuff in the can that he using after apply the fast etch in the first demonstration
@eastwoodco4 ай бұрын
After Fast Etch, he applies Pre-Painting Prep to neutralize the fast etch, and clean off the panel www.eastwood.com/ew-pre-painting-prep-aerosol-11oz.html
@DugEphresh7 ай бұрын
Dude, do you know how many morons are going to use this stuff outside on a windy day! Mask and eye protection is a must anytime you are working with chemicals. Just saying, great products and great video. Thanks for posting.
@eastwoodco7 ай бұрын
We totally agree PPE is a must, that's why Dave has his safety glasses on when spraying the fast etch and gloves on throughout.
@williamheckman4597Ай бұрын
Gonna save you a LOT of time, get a Laser Rust Remover from China.
@eastwoodcoАй бұрын
The problem is laser rust removers are very expensive - this is a chemical means that is far more cost effective.
@cart-wheels8 ай бұрын
I had bought some of each based on the amount of work I'm doing on my car. Can't wait to try them out.
@eastwoodco8 ай бұрын
Let us know what you think!
@miketeeveedub57798 ай бұрын
I have a rust spot on the lower fender of my daily driver that keeps coming back every winter. I've been using gel dissolver, etching primer and an enamel urethane top coat with no luck. I will use a rust encapsulater in the spring. Thanks for the tip!
@anah92884 ай бұрын
I’m hearing the rust belt uses a rust encapsulater after the other stuff. Etch, clean/prime, encapsulate, then put a wax based product on top every year, like Cosmoline. You can also do clear coat, but still have to use a fluid or wax film on top every year. I spend summers in Maine and never had to worry about rust til now. One summer and my van was aged over a decade! Going to be doing the series I said on the whole undercarriage. Prob one section at a time, cause it’s a lot and gonna take a while. It’ll be worth it though!
@aroundlinemen6 ай бұрын
I use it on my 56 , 63 f100 and 51f3 it work great , east wood has great product! Thank you.
@eastwoodco6 ай бұрын
Please leave us a review on the product page! We'd love to have your feedback. Fast Etch: www.eastwood.com/rust-remover-eastwood-fast-etch.html Rust Dissolver: www.eastwood.com/rust-remover-eastwood-rust-dissolver.html Rust Converter: www.eastwood.com/eastwood-rust-converter.html
@jesusmendoza16458 ай бұрын
That's good
@Rottingboards6 ай бұрын
Fast etch...so acetone neutralizes?
@eastwoodco6 ай бұрын
Yes.
@Rottingboards6 ай бұрын
I want to let my parts set for a year before I paint. Will fast etch stop them from flash rusting if I keep them in dry storage?
@eastwoodco6 ай бұрын
That's not what it's designed to do, we recommend putting the parts in primer at least if they're going to sit.
@Rottingboards6 ай бұрын
Thanks for the quick replies. You products are top notch! @@eastwoodco
@dannykanchanarin42956 ай бұрын
FYI with the liquid rust dissolver, do not leave any metal part in this liquid over 24-36 hours especially thin metal parts because this chemical will dissolve more than just rust. I had left bolts, screws, clips and even sockets submerged in this chemical for over two days to remove all the rust off and everything looked like the aftermath of metal spoons used to mix caustic chemicals in cartoons! I’ll be the first to say the product works, but definitely a little too well so whatever item being covered in this chemical needs to be checked every few hours to monitor progress. Also if the part is cleaned with hot water, it must be forced air dried immediately along with coated with a chemical such as metal wash to prevent flash rust from forming.