Automotive Paint Removal - Tips & Products You Need and How To Use Them - PART 2 of 2 - Eastwood

Part 2 of 2. In this video that originally aired LIVE on Friday January 17, 2014, Matt demonstrates many of the techniques available for removing paint and primer, including 3M Bristle discs, Gel Paint and Powder Dissolver, Flap Discs, Stripping Discs, Sanding Discs, Blast Systems and grinders.
Visit Eastwood: www.eastwood.c...
Part 2 of 2. In this video that originally aired LIVE on Friday January 17, 2014, Matt demonstrates many of the techniques available for removing paint and primer, including 3M Bristle discs, Gel Paint and Powder Dissolver, Flap Discs, Stripping Discs, Sanding Discs, Blast Systems and grinders.
Are You an Eastwood Guy?
Eastwood has everything you need to do the job right, including welders, plasma cutters, paint and paint guns, rust solutions, powder coating supplies, metal fab tools, hand tools, fender rollers, soda and abrasive blasters and more.
Since 1978.

[@Demondal]

Thank you for this video. I'm about to strip my engine bay down for a repaint and wasn't entirely sure what to use. Very helpful.

[@ludditeneaderthal]

when using the alkaline strippers (non citrus), keep a small "finger bowl" with lacquer thinner in it. the lac stops the stripper "biting", and is quite nice for the little splashes onto sensitive flesh that seem to be burning their way to shanghai via the bones in your wrist, or your belly, or those delicate spots not so mentionable on so "family" a comment board, lol. NEVER let stripper dry on the panel, re application on top of dried just makes awful, smeary, sticky plastic goo that defies removal. warm metal strips easier than cold, but also dries the stripper faster. NEVER use chem stripper in direct sunlight, btw, it goes to goo as often as bond breaking, after chem stripping, wipe with lac to "stop" the stripper, THEN you can soda blast, prep etch, etc without ghosts of alkaline corrosives spoiling your day.

[@woodworkerroyer8497]

No one else was brave enough..... Why is this able to burn your belly?

[@ludditeneaderthal]

@@woodworkerroyer8497 lol, large pieces, waist high tank, mopping the stripper on with a Tampico roofing brush, it becomes a fairly splashy affair. Lean on a wet edge, it just becomes an itch til you peel the wetted t-shirt off the flesh... or so I read once I think, lol.

[@Motodude35]

I'm trying to strip the paint off my 1970 vw beetle of its original paint but I'm not sure what I should use and I'm a beginner at doing this and I'd like to do all the steps of stripping and priming before I send it off to painting

[@teferagetachew]

Thank you for the video. this so important for me to remove paint

[@SprayWayCustoms]

Very helpful and well explained.....I think I'm going with the stripping pad method for starts.....thanks for your time!!!!

[@SprayWayCustoms]

Yea Mike, I don't know how many coats of paint and what kind of paint on it so I think I need to just strip it down to bare metal....I was just trying to go the quickest and easiest route...

[@SprayWayCustoms]

Thanks Mike....I will be very cautious not to put to much heat on the panels.....thanks for your help

[@fuzzzeballs]

well that's answered my question! chemicals and sand blasting it is

[@eastwoodco]

Glad we could help!

[@marenghi123]

The yellow 3m Bristle disc will leave a 80 grit scratch ?

[@jockellis]

People don’t seem to realize the grinder turns in a direction that tightens the threads. I’ve seen people put one on and put all their strength into tightening.

[@AgentWest]

They do have to be at least somewhat tight. I have an air powered 4.5" grinder that loves to throw the discs off. Had to chase one or two across the shop before! :)

[@SteveDavisCarGuy]

The gel method, does it need to be neutralized?

[@CJurasin]

I wetsand the panel when I've got most of the paint off.....and the water neutralizes the stripper. Just wipe the water off immediately after and you can coat it with Fast Etch or a similar product.

[@richardhawkins879]

I think I'm becoming a EastWood Guy....

[@eastwoodco]

Awesome!

[@jockellis]

Tool ownership is a slippery slope.

[@mrgoodtimes05]

If someone is stripping the threads out of plastic discs they are more than likely hitting the edge of the work piece. It will jolt the disc tighter causing the threads to pull.

[@timothyjrosser1]

after you have got the paint off with the chemical stripper, what steps would you take before painting? Would a wipe with some white spirits be enough to remove it?

[@JordanPayneLV]

Awesome 2 part video!

[@CFDJohnnyE]

Regarding media blasting.....if my work is contained to a small area in the garage, can it be neatly swept up and reused?

[@Just_smile89]

Is it okay to use the chemicals on a steel bumber and plastic grills ?

[@LH-spec09]

Thank you.

[@beznerindustries3057]

can i use a tiger wheel or a flap wheel to strip surface rust and paint

[@phreaktor]

What psi is needed for the smaller media blasting kit?

[@ArchivosMusicales]

Good question. I would like to know as well.

[@abdullahsaad9340]

Nice video 👍🏻

[@jeffreydeutsch7336]

I guess it is self evident but the bristles are more than plastic. They are impregnated with a ceramic abrasive. I would like to see a comparison between the coarser bristle brush and the coarse 3M roloc pads like the purple one or Norton's Gold one. I would like a comparison between the plastic bristle brush and the stiff unbacked woven hard wheels in general.

[@moneyhustlebizniz916]

I'm new to this stuff. I have one question though. I am interested in the media blaster you have there. The blue one. If I was to purchase one would that be it or would I need an air compressor? I have an 80 gallon air compressor in my garage. Can I use it with that or is the media blaster you have there in the video it??

[@michaelkaser2219]

If you get an engine back from the engine shop but won't be working on it for a little while is it okay to spray the machined surfaces with fast etch? (cylinder walls, cam/crank journals)

[@eastwoodco]

I don't recommend Fast Etch. Ask the engine builder what they recommend, which will likely be coating them with oil.

[@jokat98]

Money hustle, I have an 80 gal also and have this blaster, and my 80 cannot keep up with this blaster

[@jesus_built_my_hotrod]

Good video but would have been better if you demonstrated the blasting

[@englishrose212]

My car is peeling like a skin I can pick it off, is there any way to cure this or do I have to take it in for a respray ?? :O)

[@KWW0321]

Yeah spray glue on it and take the pieces and put them back on like a puzzle:)

[@jockellis]

Soda blasting leaves a film which is pH base. Does this need to be removed before painting?

[@eastwoodco]

Yes. that film must be removed. We recommend using Eastwood PRE Painting Prep, available in aerosols or gallons. Visit www.eastwood.com.

[@MotoGPatrick]

Pretty much any media leaves a film. I've used plastic media on aluminum aircraft skin and we used products similar to this companies fast etch and then Pre as well as alodine. At home, I've found a wet media blaster kit on a high power pressure washer to be awesome. I used Rustoleum gell rust dissolver first on axle rust and on a used Deaver leaf spring pack I stripped and refinished. I'm ordering the fast etch and pre. Really just have good paint and rust-free sheet metal but axle and light frame weld rust. Corrosion control protocol on an off-roader.

[@norbertrudas9852]

Hi guys, I have a question, can I use brake fluid for paint removal gel ?

[@nathanoppermann8896]

what about aluminum or aluminum boats best to use

[@andrews5926]

I bet you could find some specific blast media for aluminum

[@eastwoodco]

Are YOU an Eastwood Guy? Check out this video from Eastwood to find out: Awesome Office Pencil Sharpener - Sharpening the Pencil - Are You an Eastwood Guy?

[@coodeville1091]

i know a guy who used the paint stripper and then had to take a piss

[@eastwoodco]

To purchase a product, click a picture at the beginning of the video. And don't forget to SUBSCRIBE to our KZbin Channel to get all of our great videos.

[@michaelcampbell6011]

Dude love your explanations but like we need the chemical . Go old school start Fromm begging everything needs to be removed including rust

[@davenameless]

How long does the phosphoric coating protect against flash rust?