Easy Carbon Buildup Removal from Pistons - How to Clean Pistons & Make Them Look New Again Tutorial

In this video I go over how to remove carbon buildup from your pistons easily and make them look like new again. This is super easy!
Build Update: Addressing Turbo Manifold Heat Issues and What's Left to do before we hit the Dyno
AEM Boost Controller - amzn.to/3k9Ujiq
100$ OFF code for the street performance turbo : Matthew100
bit.ly/3ubpXls
10% OFF code for all maxpeedingrods products : MATTCHEVY
Blow-off Valve link:bit.ly/3CPR7Qa
Maxpeedingrods web: bit.ly/3DK0Ut0
Installing the $113 eBay Turbo on the Chevy Cruze 1.8 Daily Driver Part 1 - • Installing the $113 eB...
The eBay Turbo is Building BOOST!!! Chevy Cruze 1.8 Daily Driver Build - • The eBay Turbo is Buil...
PCV Issues we had - • Something Went WRONG w...
Making an equal length turbo manifold - • How to Make a DIY Turb...
Making a log style turbo manifold - • The DIY Turbo Manifold...
Custom Forged JE Pistons - • Custom Forged JE Pisto...
How to Install an Upgraded Fuel Pump - • How to Install a Repla...
Custom Camshafts for the 1.8 Cruze - • My Reground Camshafts ...
Upgraded Stage 5 Clutch and Aluminum Single Mass Flywheel - • Single Mass Aluminum F...
Be sure to follow me on Instagram to get the inside scoop...
►Instagram - @matthewchevalier
🔔 Subscribe and hit the bell to support me and so you don't miss a thing!

[@johnsnow1355]

I am always amazed how squeaky clean you always get engine parts 🥰

[@cmattdabrat]

Thanks!

[@jay1185]

Thanks for the tip! I've never used the big cans of that stuff.

[@cmattdabrat]

Any time!

[@jimmyfavereau]

thanks Matt great background tune at the end of the vid!

[@cmattdabrat]

Thanks 👍

[@jqureshi4943]

Awesome tip, will definitely be using this method in the future!

[@cmattdabrat]

Glad it was helpful!

[@user-rv7od7mv9h]

Tried this same stuff on motorcycle pistons and so far they have been soaking for 3 days and the carbon is still rock hard 1

[@johnnyturbo8460]

Another great video! Well done

[@cmattdabrat]

Thanks!

[@802Garage]

Nice tip man!

[@cmattdabrat]

Glad to help!

[@danssv8]

Nice one Matt

[@cmattdabrat]

Thanks 👍

[@watson6401]

Definitely gonna try this. My pistons for my miata are looking a tad gross

[@cmattdabrat]

Will work nicely.

[@delatuned]

You made that look easy

[@cmattdabrat]

The Chem-Dip made it easy. I didn't have to do much.

[@TruckThisGarage]

Did you replace the rings. I’m doing a refresh on my engine wondering if I can get away with using old rings. Motor ran great but timing chain needed replaced so just tore down motor to double check things

[@cmattdabrat]

I kept the same rings. Just did a light dingle ball hone and put them back in. No smoke, ran great.

[@TruckThisGarage]

@@cmattdabrat darn I’m not so lucky. First ring I took off snapped. Any idea what the stock sizes are I’ll need to replace? Thanks 🙏

[@kylelane342]

When u gonna upgrade the cooling system especially for this Texas heat

[@kylelane342]

Stock doesn't seem sufficient enough especially for west Texas

[@cmattdabrat]

The radiator has been fine. Just everything is so tight in there. Not much clearance.

[@kylelane342]

@@cmattdabrat I'm upgrading mine from a single to a dual fan setup to hopefully keep everything cooler looks like we gonna have a summer this year here in Odessa already 110

[@danieldegg1]

yep since my hemi shortblock is taking forever. ill be doing this and building it back to stock until i get my parts..... nice tip i was just looking for something like that lol

[@cmattdabrat]

lol, clean her up and toss it back together.

[@jimhiscott2918]

How many miles were on those pistons Matt?

[@cmattdabrat]

122k

[@builtbybagsy]

Looks like a good product. Shame it's not stocked on shelves here in Australia.

[@RazoE]

Dang! Let me dip my valves in real quick 😁

[@sinformant]

I was thinking the same thing. I wonder if this would work by filling your intake runners and letting it set. #directinjectionproblems

[@cmattdabrat]

I've done that as well! Anything I could toss in there. If I couldn't toss it in there, I'd brush it on parts.

[@cmattdabrat]

Would definitely make easy work of caked up heads. Just leave the valves in and fill em up.

[@barenekid9695]

Chem dip is only a V slightly different formula than Laquer thinners. What REALLY! works is Aircraft aluminum Paint stripper.

[@coltonberry9579]

imma just throw both my heads in a bath of that stuff😂🙏🏼

[@cmattdabrat]

That's what I did. Well, I would just fill the chambers with it, and brush it on. Then rinse it. Makes easy work of carbon.

[@marekgazi7939]

Hi I'm want to ask you need to remove the piston rings

[@cmattdabrat]

Leave then in so they'll get cleaned up, and you can rotate them between dips to help clean the rings lands. Pull the rings afterwards to make sure you got rid of all the carbon.

[@djmyth84]

Is it safe to work with that chemical without gloves?

[@cmattdabrat]

Better toss on some gloves.

[@rockytop4]

Those cracked rods? Like the 1.4

[@rockytop4]

Berrymans cemtool 12 is a great fuel additive cleans while driving

[@cmattdabrat]

They are.

[@Romeo_STO]

Хорошее средство.Пробовали его когда кольца уже не двигались?

[@cmattdabrat]

Not yet! I’m sure it would do the trick though.

[@Romeo_STO]

@@cmattdabrat Ясно, спасибо.

[@Romeo_STO]

Простой очиститель деталей карбюратора творит чедеса))😀

[@a2cryss]

Shouldn't the pistons be cleaned after polishing since that stuff is an abrasive?

[@cmattdabrat]

Certainly. They were clean after the fact. Just showing how you can get them looking new again.

[@mobileterminaluzer1858]

Pour some & let it piston soak when removing just the spark plugs.

[@racekar80]

The new Berryman does not work like the old one, they must have changed the formula

[@inferno493]

Doesn't work at all for me, my pistons still look like hot garbage after 3 hours.

[@cmattdabrat]

Did you give them a light scrub after 15 minutes or so? It's not just magically going to wipe off but will slowly eat away at it.

[@inferno493]

yes, I ended up taking them to a machine shop. The carbon was extremely tenacious and repeated soaking and scrubbing with a scotchbrite cloth had no effect.@@cmattdabrat

[@Forged_RSV4]

Crazy. This stuff in Canada to try to find is 75-$125 😐👎🏼 So difficult building cars here, there is next to zero parts manufacturers, shipping / import fees are insane, and our dollar is worth 3/4 of the US dollar. Plus there’s usually free shipping (on any of the sites I use) within the 48 states I have found buying my parts from Aus/UK are better deals and just waiting for the longer shipping times

[@cmattdabrat]

Didn't even think about that. Yikes!

[@Forged_RSV4]

@@cmattdabrat I wish I lived down there, any state would do 🤣

[@cmattdabrat]

@@Forged_RSV4 lol. You could get away with a lot of stuff in Florida.

[@pancake_5703]

@@Forged_RSV4 honestly never thought this would be an issue but damn that sucks, I wouldn't be able to build cars if this was the case for me lol.

[@nheng6913]

And you've just scratched the surface on reasons to get the heck out ... more to come.

[@isaaclerma4847]

You didn’t mention that you replaced the RODS. ???

[@cmattdabrat]

Well, wasn’t part of the topic for this video, but I did replace them with upgraded H beams.

[@604pmei]

Seems like 1 can can last a lifetime

[@vwbora26]

Berryman is 80% xylene

[@thra5herxb12s]

This is most definitely not carbon, this is very slight oil staining. Carbon is a solid crust that needs to be scraped off with a chisel.

[@cmattdabrat]

I'll agree with you about the crust. Find a part that has carbon build up. Toss it in a can of Chem dip for 15-30 minutes. Scrub it. After a few dips, the carbon comes right off. I've done this with plenty of car parts that had carbon build up. Eats it right up.

[@oo0Spyder0oo]

That’s not carbon build up, that’s just stain. Real crusty carbon pistons and heads are not shown here.

[@user-no6cf5cu2p]

Haha, doesn't work on caked up deposits at all and I left it sit for 24 hours. This is a cherry picked example