Easy Factory Amp Bypass 2002 Chevy Tahoe GMC Yukon

Did you like this video? If so, please consider becoming a Patreon Member to support this channel. It will help me bring you more videos like this. Here is the Patreon Link: / tahoesteve
Easy Factory Amp Bypass 2002 Chevy Tahoe GMC Yukon
Link to Savage Home Automation Article: www.savagehomea...
Link to Z71 Tahoe - Surburban Forum:

[@ThePOPAJOE]

You should sell these connections/ I definitely would buy buy for the bypass, use the vids and the product to get paid

[@juniorcantor9719]

I have a question would it work on a 2003 Silverado

[@TahoeSteve]

I'm not sure as your 03 is a generation newer than mine (99-02)

[@DAskew]

You used 2 harness connectors to get 8 wire connections? I got 6

[@04DynaGlyde]

Thanks for the tip!!! 👍🏻👍🏻👍🏻 EVH 🎸🤙🏻

[@TahoeSteve]

EVH forever! Anytime

[@smokey210210]

I have a 2003 GMC Yukon and I wired the harness the same way n I didn’t get no sound out of the speakers.

[@smokey210210]

I’m still working on it

[@TahoeSteve]

03 new Generation. Stuff changed from my year

[@kevinmarlow8719]

So my 04 suburban with bose amp. is different than this video?

[@TahoeSteve]

Yes!

[@edgarrivas6598]

You mention ur sub worked at the end of ur video with just using the Metra 70-2002 is that correct?

[@TahoeSteve]

@Edgar - In my situation, I have an aftermarket sub plugged DIRECTLY into the aftermarket amp. In this case, you do NOT need anything besides the Metra 70-2002. Keep in mind that the D Piller tweeters will not work though. IF you have an aftemarket amp and your sub is NOT wired directly to the amp, then you will need both harnesses as described on www.savagehomeautomation.com/projects/bypass-factory-ampcrossover-in-2002-chevy-tahoe.html.

[@lisacostilow4817]

, if I do that that means I do not use my Bose amplifier right all four speakers will work without the ant working

[@TahoeSteve]

to my understanding, it does not work with a bose system.

[@marqkirby9837]

you showed only a1 to b9 does it go downhill from there??

[@TahoeSteve]

Not at all. It's just a very repetitive process. Everyone between A1 to B9 was exactly the same. I didn't want to bore the shit out of you by showing every one.

[@gas2419]

Steve...I know this video is over a yr old but thanks. When I searched for bypass Chevy Tahoe LS 2002 factory amp... You video popped up and here I am! Thanks first most! But will this work for my car also? Also wiring it this way I called Crutchfield for the 70-2002... Will configuring it your way power all 9 speakers discluding the tweeters in the pillar? Will it work with the tweeters in the front? Sorry about the long question bro... But thank you in advance!

[@jackkhol4251]

Did you ever hook it up? How did it work? I have a 2001 Tahoe . Do I need the 70-2002 harness?

[@gas2419]

Jack khol Works just as advertised... Got the harness from Best buy... Took about an hour tops... Just pop the pins out and follow the video just like he says! He nailed it on the head!

[@jackkhol4251]

Awesome thanks.

[@willgates6620]

all of a sudden my speakers dropped volume midrange ane bass. They all sound like distorted tweeters, is that my factory amp? I've installed 3 different head units and it sounds the same. will this bypass work on a 04 suburban?

[@CarlosGonzalez_753]

How do you do it on a bose amp on a 2004 chevy silverado 1500

[@HAMBONEM]

Do u have to pull the pins? Can i just splice the wires to the pins without pulling them out?

[@Tracert-mc1hu]

That's what I'm going to try. I don't see why it wouldn't work.

[@Lordvoldemore]

Why is the amp still plugged in? Would anything change if you unplugged it? My factory amp makes a white noise.

[@jdrecyclers2441]

I have a 03 Chevy Avalanche 1500 with Bose. Will this same diagram work for my truck?

[@jadenbright3854]

No

[@markanel]

Do your steering wheel controls still work for the aftermarket radio?

[@michaelstewart6689]

Good afternoon I would like to see if you can make me one of those I have a 2004 Chevy

[@zogmontanastyle7348]

What is speedwire? I've been installing stereos since 1990, and I've never heard that term. Low level input, high lev, yes. Speed wire? No

[@ernestopineda4996]

Google it, basically is one thick wire with all 4 speaker wires inside to easy connect all together

[@csizzle1]

A group of wires with different counts. Most run a 9-wire. Has 9 wires. 8 pairs and 1 remote wire.

[@unmademusic]

I can't get the amp to move after removing the top clip like something else is holding it in if anyone can help

[@markgardner42]

I'm having the same issue. I've removed the clip but the amp won't move. I feel like I'm going to break something if I force it.

[@mijohnst]

I just did this, thanks to your video and article you posted, and I cannot believe what a difference it made. I hadn't even realized that I was even missing out on anything. My door speakers are now all pushing base which makes the experience even better! I'm amazed! Thank you again for the time you take to do these videos. :) It is very much appreciated!

[@TahoeSteve]

Glad it helped!

[@jayvalentin018]

Metra 70-2021 is the part number for one already made $13.26 as of Jan 2023. Not full proof. Gotta swap a couple wires around but apparently works.

[@danielduncan8345]

With stock radio?

[@jayvalentin018]

@@danielduncan8345 yeah I still have the stock radio in. I might make a video on it. So when I do I’ll send it.

[@danielduncan8345]

So your saying installing that part , with stock radio , you will have sound out of door speaking ?

[@jayvalentin018]

@@danielduncan8345 all 4 door speakers work yes. It’s wired the same way he stated in the video that he’s using

[@mu9627]

Hey, when using the Metra 70-2021, how does it effect the sub and rear d pillar speakers? Thanks for sharing btw!

[@condor5635]

great video! thanks.. i have an 03 suburban that the OEM head unit (6 changer CD) with bose speakers. the speakers lose output but the head unit remains powered. hitting bumps or something intermittent cause it to go on and off. The ding ding ding door lock functions is also silenced when this happens. ARGH! I have heard it could be a bad ground in the A column but now that you have shown me there is a separate amp i am thinking it is related to that because like i said the sound out put is affected but the head unit remains on all the time. Any ideas or insight? thanks so much!

[@ace4u79]

I also have a problem like that bro I hit a bump once and now it starts playing for like 2 minutes and then I lose power

[@davidalvarez-lucatero9931]

Is this the same for a 2011 Ltz extended Silverado?

[@averageViewer5]

Just wire nut your speaker wires to the wires coming from your aftermarket deck. much easier for us who dont like doing pins

[@blastztrixx]

does that not work when using factory speakers?😂

[@mobilemike8500]

I'm a 50 year Auto Tech I just want to let everybody know that the bypass is fine but pay close attention to the positive and negative to the speakers as GM release their wiring schematics incorrectly to the public I own three of these vehicles and I found that the positive negative configuration in the speaker wiring diagrams for these model trucks is incorrect... the a connection at the speaker is the positive and if you look at the schematic going back to the head unit or the amp it shows it as negative on all the speakers ...that is not correct so Crutchfield and Metra and all these people are supplying these quick connectors for aftermarket speakers and everybody's wiring their speakers in reverse polarity even the stereo shops don't even know what they're doing it's funny because a phase tester only cost ten bucks from China I also found that on my 2003 Yukon XL with the Bose system my rear door speakers are in reverse polarity I contacted Bose to see if that was done on purpose and nobody has the answer to that of course I doubt it was done on purpose somebody dropped the ball there too happens all the time in this business and all the KZbin videos are showing people how to wire the stereo speakers in reverse

[@jackkhol4251]

Really? That's F'ed up. Why wouldn't GM fix that error? I'm about to by pass and wire up an entire after market system in a 2001 Tahoe and your comment has me worried

[@mobilemike8500]

Jack khol if you can test it from the head unit all the way to the speaker's you won't have a problem but what I found is that all the positive and negatives are reversed in the schematics for the Chevy there is also a polarity Checker CD or download for your phone that you can buy and then you put the tester at the speakers to test them after you get everything installed and make sure they're correct you can buy them from China for like 15 bucks call the speaker polarity tester I don't know why everybody doesn't have them

[@jackkhol4251]

Thanks for the reply. So you are saying every Chevy during these years are like this? I'm working on a 2001 Tahoe without Bose system.

[@jackkhol4251]

And it seems like I could just reverse the leads at the speakers if that was the case correct?

[@mobilemike8500]

Jack khol I'm just saying you can't trust any wiring schematics part of the problem is the rear speakers were 4 ohm speakers and they flip the polarity around on the speaker connectors so they reverse the wires but the problem seems to be that the A&B is not labeled correctly for positive and negative and nobody has ever picked up on that and nobody really ever checks they just put speakers in and hook them up the same way they were and realistically if all your speakers are wired in reverse polarity you probably won't notice it much but they do make cheap polarity Checkers to tell you if they are in phase to me all these high-end stereo shop should be using polarity Checkers because a lot of people's cars I work on I check them and their speakers are wired in reverse polarity

[@kevincaduff4010]

Hey instead up splicing wires to bypass the factory amp, you can unplug that same 24 pin harness from the amp and plug the aftermarket radio / new harness directly into the same harness you just spliced or bypassed

[@user-wu4fg7tc9y]

what do you mean?

[@cdboor79]

Which kit?

[@kevincaduff4010]

From the factory amp in the dashboard. Same 24 pin harness is used on the back of the radio as on the factory amp. Hard to find it in there

[@k5_kiaupgrades622]

This amp bypass was awesome. But they actually make a harness already for that. It’s the metra 70-2021. Plug and play. I just did one 2min ago on a 2002 Tahoe

[@danielkruckenberg9882]

U just saved me so much time thank u good sir

[@k5_kiaupgrades622]

@@danielkruckenberg9882 np at all. 👍

[@mikem8475]

Me too been working on this damn thing for three days now

[@randymurdock2547]

Everywhere says it’s the 2000-2001 Monte Carlo/impala is that the correct one?

[@k5_kiaupgrades622]

@@randymurdock2547 the harness? Oh what do you mean?

[@SunnyD206]

Just did this to an 01 tahoe non bose. Fixed my no sound issue.

[@chrisscott373]

my 70-2002 only came with 14 wires. do not have enough to repin. Where can someone purchase a bag of pins and just make new wires. Skip the soldering altogether.

[@paluewutitdew2200]

Only one speaker work in my car and that's on the right side. The 2 backspeakers just went out I'm trying to hook up 2 new apps and 412 speakers, and the last 2 back ones went out. Now I'm trying to make sure all my speakers are working on all 4 doors and the extra 2 went back to deep pillars and not the on the internet. That's showing me how to make my 2 back door speaker's work and the D pillar speaker's work.

[@mauriciorosales5971]

They sell a bypass now online pre-made, its marketed for an 01 Monte Carlo but I read that it worked for an 02 Tahoe. Ordered it and will find out soon, it ranges from $8- $15

[@mauriciorosales5971]

It worked perfectly, if I could post a photo I would. It was advertised as an amp bypass for an impala/monte Carlo and came prewired, didn't have to do any modifications. It was pretty much plug and play for my 02 Yukon, amp was in the same spot as this video

[@carsonday5748]

I should have read the comments I could have saved time and ordered the same thing for 12 bucks but hey at least I have the satisfaction to say I made my own wen ppl ask lol

[@ryanmccausland6497]

Tahoesteve, i just did this bypass after watching the video! Now i need better speakers hahaha (I listen to metal) very easy. Only took me 20min. Thank you for also explaining how to still use the back tweeters and factory amp/sub!! I love everything about my 01 LT, but the sound system definitly wasnt impressive..till now!

[@TahoeSteve]

Nice work! I've been listening to Hard Rock/Metal/Thrash since the 80's so I understand the need for a good sound system. Thanks for watching.

[@marcuselon]

i have a 2001 tahoe and i just pull the fuse under the hood...25 RDO AND IT SHUTS DOWN AMP AND YOUR FINE..ALLL THAT WIRING SHIT IS UNNECESSARY

[@joesanfilippo8708]

I pulled the RDO AMP fuse and lost all audio...

[@antovio6162]

Is there a way to connect the back pillar speakers and sub?

[@Tracert-mc1hu]

Yeah, you can wire in a second harness as well that plugs into the amp to make the tweeters, D pillar speakers, and stock sub work as well. That was the first diagram he showed in the video.

[@BubaJ1000]

Question. Why can't you run the speed wire to the plug on the amp? plug it into the plug at the amp instead of the plug behind the stereo?? And how may channels does the amp ave to run those speakers??

[@TahoeSteve]

If you are installing an aftermarket amp, you can run speedwire to the amp, or rerun your speaker wires directly to the amp. I have a 5 channel amp. One for each speaker and a subwoofer.

[@carsonday5748]

Thanks man for this video. I just sat down and did mine just gotta go out and install it. Huge thanks

[@ewstxit1975]

Make me one bro for a 04 yukon

[@redbullminifridgepcbycusto8204]

Steve... Thank you for this tutorial! I'm working on it now. Question for you.. Using a sony dsx-gs80 hu and plan on hooking my 8" sub to it. Where are the wires for that sub? On the amplifier? And do you know if I can bridge rear channel on a hu to this sub or do I need to just use channel 3?

[@TahoeSteve]

I'm not 100% sure how it was originally wired to the sub. I added an aftermarket amp and sub and wired them directly and did the amp bypass.

[@stonigee7997]

If i comepletely bypass my factory amp will my aftermarket stereo alone be enough to power my door speakers? Or should i still use the factory amp for the door speakers and my aftermarket amp for my subs.

[@blueflowers6738]

Depends on the new head unit. I'd prob go with one or the other based on installation time/effort rather than performance if the difference is only trivial. You'd have to be more specific about your factory and new equipment if you wanted to get a specific answer though. Good luck on your project!

[@4486xxdawson]

Wouldnt be a real diy without a little blood , i hope i can use this video to fix my 99 yukon stareo , someone installed a regular stareo to the bose system and i dont have any front speakers and right rear door speaker . The left rear door works and 2 speakers at tail gate work also sub woofer seems to be working all though i cant find it lol . If anyone can help or direct me to some help i would appreciate it very much since i dont want to go back to stock stereo lol nobody uses tapes any more ..

[@TahoeSteve]

thanks for watching

[@Pappasquatch]

So..in response to one question you said yes your factory sub still works, then later you say it only powers the four door speakers. Which is it? I want to do this to keep the factory sub yet use the new head unit to power the four door speakers.

[@TahoeSteve]

If done right, it can be reversed so the factory amp will work. However, once you apply the mod, the point is to use a better aftermarket amp.

[@sidneymeyer6668]

Hello, do you sell this setup for my 02 chevy silverado 2500hd 4 door crew cab? Or is this something I can maybe figure out myself? Also does my truck come with this factory amp setup like the 02 avalanche? Thanks.....

[@TahoeSteve]

the point of the video is so you can follow along and just do it.

[@joshcrosland8733]

I know this is an old post so I may not get a reply, but im about to bypass the factory amp also and had a question. Did you have to use a 4 channel amp to send signals to the amp using the RCA and speed wire? As in RCA's to give the sub sound signal and speed wire for the door speakers? And if so do you have to splice the harness coming off the radio? thanks for the video!

[@dabloesco]

Sure you figured out by now but just in case LOL. If you are installing a sub only and have factory Hu you run a proper and that matches as close in rms not peak to you sub so sub handles 600 rms at 2 ohm then try and find a ame with a rms of 600 watts rms is steady power what it outputs like 1200 watt doesn't matter as much as rms in all speaker installs. Then your run the RCA and Renate wire which is what I assume your referencing as the speed wire. That goes into the back of Hu they make adapter for stuck headuncts called line convert out I think,, basically extra part I0 connect your rea and remote wire non of you already have aftermarket hardest which I wou ld get first for any upgrade you went need the loc it will have RCA and remote wire connect on radio harness already. Same goes for door speakers get a 4 channel run set of RCA and remote wire to headunit and then speaker wire goes from amp to each door speaker. You have a +/- wire going to each and that's how gu run aftermarket speakers and amp. You can also get a five channel amp, which will give you the same concept except you only have to run one set of RCA’s and remote wire(speed wire). There are other configurations and I’m pretty sure you can buy RCA wires to run directly in some head units and amplifiers. I’m sure there’s other tips in anyone will correct me if I’m wrong, but this is just a general explanation. Also, you will have to run your power wire and ground wire for the amp obviously but I didn’t mention that. Hopefully you were able to figure it out either way. .

[@Chatomino]

I use the factory amp just for the four speakers, Independently set of wires for my amp and woofers. Im not doing all this lol.

[@Catholic1391]

What about the vol control on the steering wheel?

[@rickybobbygang6677]

Thanks so much it worked great awesome step via step my Tahoe sounds amazing with the amps now I see roll off effect is gone I have more control of sound and can crank it thanks Tahoe Steve

[@TahoeSteve]

Glad it helped

[@woogmaster101]

Will this work for a 2006 chevy trailblazer

[@rcsix3rd]

Is it gonna be the same diagram for the 2000 tahoe no bose. But plug says needs to be a metra 70-2021???

[@wadehulsizer]

Metra also has a 70-2054 kit it is the 24 and 8 pin harness for those that want to bypass both.

[@michaelgracephotography8308]

When you say both, what do you mean. This video shows amp bypass. What else can I bypass.

[@Thehotboxhangout]

Hey quick question, so my doing this bypass would it cut the power to the amp? I’m asking this because I’m having my amp stay on and kill my battery.

[@nickb1776]

Did you figure this out? My battery has been dead 2 days in a row after full charges.

[@Thehotboxhangout]

Nicolas Brown yes It did I bought this bypass from amazon for like 10$ my problems was that my amp was staying not turning off, I recommend pulling the amp fuse if it fixes the problems buy the bypass, it’s cheaper than a used amp and it sounds 10x much better without it

[@TKD187]

Okay so if I hook the radio up just normal and then come off of my amp to the factory speaker that eliminates that whole problem right cuz I really don't want to go through this I think it will be more work but I will save a little and headache

[@TahoeSteve]

yes.

[@TKD187]

@@TahoeSteve ok but when I tie my harness together all I should tie together is my power ,signal and ground right the door speakers in the front are disconnected but there are still some speakers in the back that are not disconnected so even though I have my main speakers I'm going to be using running straight from my amp if I tie the harness in color to color for all wires then the leftover speakers are going to be running through the factory amp and make it sound like crap right ? Kind of a rhetorical question lol it just sucks because I want to use them highs

[@MaxxTheSavage]

Am looking to remove factory amp completely, add new head unit, new speakers( with new wires run to those speakers) Where is the second link in your description to the site that had the amp wiring schematic?

[@DjNateNaSty_YT]

It's almost like you could've left the connector unplugged, find your positives and negatives to each speaker, and call it day. The harness seems to not be much needed.

[@zacharypowers1979]

does this work for chevy silverado’s 2004?

[@TahoeSteve]

No. 99-02

[@bradysolaem2467]

Thats the way to do it similar scenario on my personal vehicle 95 sedan deville factory amp in the trunk shit can get hairy if you dont proceed with caution plan your next 3 steps and your undo button BEFORE YOU START SEVERING THEM FACTORY PIGTAILS N HARNESSES I USE QUICK CONNECTS AND MALE BUTT CONNECTORS QUICK IN AND QUICK OUT ALREADY TOOK IT BACK TO STOCK BOTH WAYS WORK SOUND GOOD MINUES LOOSING LIKE 7 SPEAKERS

[@plebeZ]

And that was the easy one Thanks for watch 😎👍

[@TahoeSteve]

Thanks for watching

[@draconis112]

Thanks for the video, great guide! You can also use the Metra 70-2021 as well if you don't want to DIY the wiring. I'm not 100% sure if it would kill the rear sub/tweeters but I am getting ready to install a new headunit in my 02 suburban and may have to give it a try.

[@TahoeSteve]

appreciate the comment.

[@michaelgracephotography8308]

How did the 70-2021 work out with your install. I have a new head to put in and want to bypass the amp...

[@draconis112]

@@michaelgracephotography8308 Worked good, all the speakers still worked including the sub. I replaced the OEM speakers with Infinity Ref and a pioneer shallow mount sub.

[@michaelgracephotography8308]

@@draconis112 I've ordered what I need, can't wait.

[@jes1kbs2002]

thanks man. I did it without buying the clip.

[@michaelgrindle1365]

jes1kbs2002 jk

[@luismontemayor5713]

How did you do it man im going crazy with mine

[@violater7026]

Just to play music with another head unit u have to bypass the amp Or do something with the harness Some weird shit Best Buy did because it wouldn’t play music at all Finally worked Sounded shitty with new speakers

[@nateweiner8890]

If I go this way, can I just wire a normal amp and sub in the back, bypassing having to get a speedwire and 5 channel amp? Planning to upgrade my 02' tahoe and hoping I can get away with a new head unit, amp, and sub. Thank you!

[@Username-ng8jy]

My plan is to physically remove the amp. Maybe even go far as removing the wiring. I’m doing a full system in my 03 with Bose. I’m gonna trace and label each speaker wire. And tap in them thru the back of the radio. Or if not I’ll just tap into them from the factory amp location. I’m gonna put the amp under the passenger seat anyways. So I’ll need a short run from my speed wires to the harness at the amp. I’m not tryin to revert to stock anytime soon. Lol Bose is nice. But much nicer set ups out there. It is a bit dated. It’s time for an upgrade.

[@Username-ng8jy]

Let me know what route you took. I plan on doing a full upgrade. So I’ll let you know how it goes.

[@nateweiner8890]

@@Username-ng8jy I ended up getting a 2010 tahoe with Bose and put another amp and a 12’ sub into it, so I went a seperate way

[@Username-ng8jy]

@@nateweiner8890 ah ok man. That’s cool man. Hope you enjoy the ride. I got an 2003 I got earlier this year. With the holidays coming up. And free time. I’m finally fucking with my tahoe. Just got my tranny rebuilt with sonnax shift kit corvette servo and upgraded converter. Got carpet on order. And need to repair my headliner. I got a wood steering wheel I’m refinishing. Black Friday deals popped up so I’m ordering my sound equipment.

[@731u.s.a5]

How did u get a double din in ur 02 ? Been wanting to put one in mine

[@RayRayP2001]

put a 2003 and up bezel in it (the part you pull off to put radio in), the hole behind is big enough for double din, but bezel on 2002 only has cutout for din and 1/2 2003 has double din cutout.

[@TahoeSteve]

see this detailed video: kzbin.info/www/bejne/hInam4WXqLyVq9U

[@_BebeTv_]

so i have a 08 Trailblazer ss with bose, i installed a W4400NEX pioneer double din. my question is can i reuse the pre-existing speaker wire and cut the clips off the oem amp and just run some speed wire to the location that i want my new amp to be from the speaker wire that was connected to the old bose amp ? i want to have two separate amps one for voice and 1 for subs, thanks.

[@Rawlings-de6su]

Same slots on the 16 pin connectors? How many wires there 16. Red, yellow, black, blue, then all the other speaker + wires only. What’s the pin slots?

[@michaelhernandez9035]

Hey guys I have a problem with my anti-theft system try to reprogram it doesn't program the yellow lock stays on doesn't turn off does anyone know how to reset it another way thanks

[@antoniograntwabasha5990]

I have a 2001 tahoe would be fine if I just cutt the blue and white wire that plays the factory sub. So it won't distort my own subs?

[@xxgunzgamingxx1279]

This worked for me thanks alot 💯

[@TahoeSteve]

Glad I could help

[@Ron_Masterjohn]

Awesome video and thanks for making it and posting it. So would these two Metra kits be what I need for my 2002 Suburban 1500 LT with standard radio not the Bose?

[@calmingrelaxationmusic513]

I have a 2000 GMC yukon, my rear tweeters just stopped working, could it be the factory Amp be the issue?

[@DaRazor405]

Did that now rear speakers as the tweeters and sub dont work now

[@jackkhol4251]

SO you are using the factory speaker wires? I have a 2001 Tahoe which has the same exact system. All the speakers quit working except the rear 3" pillar speakers. I am wanting to install an aftermarket head unit but I don't want to run all new speaker wires because of this factory amp. SO I can hook the new head unit up with the wiring harnesss from Crutchfield then do the bypass thing you just did with the Metra harness and I should be good?

[@tsturgeon9365]

All of my speakers cut off around 30 of I turn it down to around 26 to 28 they come back on would the bypass work for my truck or should I replace the amp 01 tahoe

[@TKD187]

Yeah even though I only hooked up power in the ground signal still plugged it into the factory harness there's no way around that so it is still running through the factory amp I just can't get it right I thought that my 12 sub was blown but after thinking about it ,it's just being double fed .. getting very frustrated iv hooked up lot I'm systems in this one is the hardest by far

[@brandonbill3121]

So i wouldnt need to keep the pink wire hooked up for the amp turn on?

[@elitepwnsor5219]

did you ever find this out? i assume you can leave the pink wire out because the harness bypass just connects the 8 speaker wires together forming a complete circuit excluding factory amp

[@Crazyredneckjim]

As for those wanting to buy the harness O'Reillys sells the harnesses that will work. The harness is the same. But the pins inside are not. The one I bought didn't have enough pins in it so I bought two (2) harnesses so that I would have enough pins. And it worked beautifully.

[@مِحًمِدُخٌآلَدُ-ب7ر4ذ]

Peace be upon you, brother and friend, I am one of your followers. I would like to connect Salvador Radio 2001 to an external converter. How is the connection done because the external visa is available to the doctors? How do I know the hot and cold of the speakers?

[@TKD187]

So if I just cut the harness and find the power and signal and ground and hook it straight up to the head unit I should be good right the power isn't coming from the amp is it? what I mean is the original power doesn't go to the amp first and then it branches off from the amp?

[@Jaydee6.2]

Sitting down to do this now. I depinned my harness and I don’t see it being possible with the 70-2002. I need a total of 16 pin ends and I only have 12 plus the red mess which is all y’d into eachother. Even if I dissected that I’d only have 15... am I missing something here?

[@wadehulsizer]

At least your watching a video of Alex Lifeson, one of the most underrated guitar players in the MOST underrated band.

[@xaman1874]

Way to much work it's easier than this

[@billyhernandez7540]

Y'all still having problems just take ur vehicle to a performance shop get a tune they will turn off the security system

[@themantheman-vo7wd]

Metra 70-2021 bypass work the same way and save time thanks in advance keep up the good work and videos

[@mariovillagomez9374]

Does this work for 01 yukon as well?

[@TahoeSteve]

it should unless you have the Bose system.

[@nalide_classic5444]

That is to bypass the bose I think Tahoe Steve is confused

[@norbertovargas1931]

Doing this will you still have balance fader and sub lev er l controll on the radio?

[@MartinChavez-iu6tu]

What if I just install the stereo without this bypass? Would I just no get sound on door speakers? Or would I just no get lows?

[@modernmopcar1832]

Op

[@OhDatsJohnny]

Do you know where The amp is at on a 2002 silverado ext cab?

[@ernestopineda4996]

Thanks for sharing it, this will be easily for my new subwoofer install and aftermarket stereo

[@MHTwigg]

I have a parasitic draw off that thing from Onstar...when I unplug everything...draw goes away...but I lose speakers...is that plug above it the onstar? can I leave just the speakers plugged in?

[@TahoeSteve]

I'm not sure, someone else???

[@bstceltics4]

What ive learned with most car manufacturers is that it doesnt matter what features they put in your car the wireing is ussually there to plug into them so taking that into concideration if you find a truck without the bose sound system chances are there is a factory bypass plugged into the cross over plug and you wouldnt have to go threw this but its very interesting in case you cant find one in a junk yard you can still get it done

[@sergiocamarena1542]

Will this fix my issue on my '07 hummer H2? Added a after market amp and subwoofer...amp powers on but no audio....all my wiring are good...even my ground is good and bolted tight...still no audio through my woofer

[@TahoeSteve]

no. 99 to 02 only.

[@zfarmer4]

I was looking at your video and I’m trying to see how do you get your feedback from your aunt from bypass in a factory amp

[@HectorLopez-cz6ig]

Hi connected one of these 2 Chevy avalanche 02 I have a aftermarket app I install I wanna connect this bypass system It messed up everything What did I do wrong

[@TahoeSteve]

That's a hard one to answer not seeing what you did. go back and start over. double and triple check everything. this works if you do it correctly.

[@MrNeilStephenson]

Hey AVT. SO I put in a kenwood HU. And 4 pioneer 6.5 in the 4 doors. Wired up the HU to the factory harness. Jumped the blue/white wire to the pink in the 10 pin. Got audio. I know these speakers are great sounding but they sound so low. Is that because I'm going through the stock amp? I found the amp and unplugged it and yep no audio. Figured that. Any way all I want is my door speakers to work. I'm not putting in a sub. Which setup should I use? The one you did? I ask because you said you didn't care if your rear speakers worked. Just not sure. If it is how you did then I may just pair the wires together. Can you advise? Great vids btw.

[@TahoeSteve]

My setup assumes a second 5 channel amp so it would not apply to you (unless I missed somewhere that you do have a second amp). When i said i did not care if my "rear" speakers worked, I was referring to the tiny tweeters in the way back (D piller). I was not referring to the rear door speakers. Those do work. Hope that helped

[@abbondanza23]

I came up one pin short to complete the 8 wires needed. The one I bought used a two pin into one pin red wire, so there wasn't 8 pins for each side. Bummer man.

[@massey-rn8mq]

Same here. Super stinks

[@brycerowdy]

Did you have to use any pins from another harness? Or did the 70-2002 harness have enough pins?

[@TahoeSteve]

this harness had exactly the right amount of pins

[@ajmann07]

Trying to help a Buddy out with his amp and sub install His is a 04 tahoe w/bose (with rear seat video canceling while the kids watch movies) Anyone have any ideas ? Maybe a link to some videos. THANK Ü in advance

[@TahoeSteve]

this video is on an 02 without bose. The 04 is a newer generation and the bose changes things even more. I am pretty certain the setup on the 04/bose is completely different and this will prob not work for you.

[@tahoelifeb.l4082]

Hey man will these work for my 1999 Tahoe classic truck two of my fronts are working but my back is not please let me know thank you

[@hackattack7892]

waste of time that harness only comes with 15 pins where did u get the 16th? and why didn't u mention that?

[@gusparides4675]

its mentioned in the pdf file .

[@مِحًمِدُخٌآلَدُ-ب7ر4ذ]

How do I connect an external switch? How do we connect the Wi-Fi from the radio to the switch?

[@O.g.whiteboy95]

Can i do this without getting an aftermarket amp?

[@redline687]

Thanks for the information! Keep up the good work! Ill be watching!

[@TahoeSteve]

So glad to help!