This should be shown in a class if you're studying car stereo installation, great video my friend 👍 Edit earned a new subscriber

Just as a caution for anyone coming past and seeing this, click type torque wrenches such as these are length dependent, and measurements taken with force applied at a distance other than that shown by the ring on the handgrip (marked for this purpose) will not be accurate. If you're using a deadweight technique, the weight must be hung at that point and the resultant torque setting adjusted according to the ratio of the actual distance to 12". e.g. a common 15" wrench would set to 25 ft/lb for a 20lb weight: 15/12 = 1.25 x 20 = 25 (It may not be exactly 15" though, alter as required.)

Can you hear the noise?

Can you use the old clips or will I have to buy new ones

If I swap it in with the 4l80e transfer case aswell, do I have to change the front driveshaft. Will the one you got work?

Shows this part as unavailable. Axxess AXGM-04 AXGM-04 Data Interface for Select GM 2000 Through 2013 Vehicles Any idea on what to replace it with?

Just watch the c02 levels. itll probably won’t kill you but it will give you some side effects temporarily.

Love u u r 😂😂😂

I love this man you got a good personality and that's how you start a good video

First I check and tighten all connections from the turbo heater to the propane tank and use soap and water on the connections to check for any leaks. Then I set my propane tank outside the garage between the garage doors and I keep one garage door up one panel high. I set the turbo heater about 2 feet inside pointed diagonally toward the opposite corner of the garage. I set all gas cans outside beside the garage for extra caution. It does a good job heating the garage. People use propane stoves and dryers inside their homes everyday with no vents so I feel pretty safe with the precautions I take

That speed wire was a game changer for me. Thank YOU! 🙏🏼

I want to make my tahoe faster it's fast cuz the dealer I got it from put something on it for racing supposedly but I want it faster idk what I should put a cold intake or what do u think? It wastes alot of gas I noticed

Dude you got a kenwood with a volume dial! You know what sucks donkey balls? Trying to go from max volume to low via touch screen

Look at the flames if it's blue youhave complete combustion, you're fine, but if the flames are any other color something is wrong.

What a version of Raspberry Pi?

i'm 62 years old.growed up with propane heaters in every room,to much hype about co2 from propane,gas or deisel yes

“Got that, we got that , alright that’s it”😂😂😂

Perfect video..I just got the 4L80e to swap into my 03 suburban z71 some months back, and absolutely could NOT find the transfer case adapter. And thanks to you, I can finally finish the job..all I need now, is to find the 80e transmission mount..I'm swapping out to the 6.0 radiator as well

very informative . thanx .

I'm awaiting delivery of a propane heater from Home Depot. lt gets as low a -12 around here and that's just too cold for me to work in my unheated shed. There are lots of are gaps in the construction of my shed that Co shouldn't be a problem but I will get a monitor. Thanks for this video.

Hey man. This is the only video ive found on youtube that shows how to take off the bracket on the upper left bell housing both. Much appreciated brother

Omg man, I feel your pain. Thank you for making this video. I feel like I owe you a crisp 20$ and a 30 pack.

Why do Americans have no idea regarding the correct pronunciation of words ? The word Soldering is pronounced with an L ! Yes - the word has an "L" in it. Sodding is what perverts do with odd people or animals!

4 years later, these are still great videos. You really explain things very well.

I have a kerosene jet heater have had it for years and love it can get from 32 to 70 degrees in 15 minutes, gotta watch the fuel lines though they get brittle after a few years

Watched the whole journey in one sitting thank you for all the information, love love the tahoe !!!

A couple of things I did. First got a long hose and keep my tank outside (no risk of propane leak) secong I have an exhaust fan build into a 12"x12" 2x4 box to support the garage door and have thick vinyl draped down at bottom of the door. The other consideration is the concrete floor - you may warm the air but the floor will be cold so get a rubber mat or something to lay on.

Hello! I don’t know I need to change language English for RadioMaster TX16S please 🙏

I just finished mine swap 4l60 to 4l80 too,I turned it on yesterday but it goes forward and all but with no power not sure if the tranny is bad or just needs the programming

nicely done

i cant get unitrunker to install on windows 11

i

The transfer case adapter plate wasn’t in the description also thing that stopping me is transfer cause adapter both drives shaft being different cause mine is 4wd everything else seems easy to swap over can you provide a link for the drive shafts and adapter kit

My guy! This is exactl;y what i needed. I've done a ton of sub setups. Swapped out plenty of head units and speakers. I have yet to amp aftermarket speakers. This is going to help me so much! Everything is sounding great right now, but i just need a little more from the 6.5's and 6x9's. The head unit i have in right now is only pushing 17 watts to each channel. My 6.5's are rated for 60rms, and the 6x9's are rated for 200rms. Both sets are the JBL GTO series respectively. I'm gonna save this video for when i get my 4 channel amp in.

Thank you very much for the video. was the engine light on all the time? mine comes on while driving flashing... comes and goes... but comes on quicker with 4x4 or tow mode on... same P0300 code

I'd be more worried about co2 with burning propane.

Best transmission jack ever.. great work 🤘🏿

Why even heat a 53 degree garage?

I'm laughing, because I was right there with you on the snake-ing extension upper bolts situation, today. "Sh!t" and the pile of wrenches is where I paused to write this. So now,...I'm gonna continue this adventure movie, and see how it ends.

PCM of NC makes a harness that requires no segment swapping now. Just a simple shift point adjustment

😂 omg I feel your frustration I'm still working on mine 2 years later.😂😢

Doing a LS swap on my 99 Chevy Tahoe 4x4 gonna put a 5.3 with a 4L80

I'm sure it burns clean but what's more concerning is consuming the oxygen in the space for the combustion.

This may have answered a concern I have with the one that I just bought today. I realize that this vid is over 4 years old, but here's what I'd like to confirm. I noticed when you plugged it in, the igniter was buzzing away as it should. Mine does that immediately as well. I'm pretty sure that after the unit was running and working, that I hear the igniter still buzzing away. In other words, it didn't turn itself off after detecting that things were working. And THAT is what mine is doing too. I'm wondering if this is by design or if it's a fault. Perhaps leaving the igniter buzzing away is maybe a safety feature so that, oh I don't know... if the propane stops for a moment, for some reason, then flows again, this will automatically light it up. Not sure. Do you or anyone know if this is how these types works? That the igniter is constantly on? Thanks in advance.

😂😂😂😂

Bro you speak my language.. love this and hate the fact I gotta curse at this damn wiring too

So you just hookup the hole speed wire into one channel?

Great video Thank you

Can i use the same measurements for the driveshaft as you for a 03 silverado extended cab?

Hey need help removing the sub from the box can’t seem to jam it loose any tips? It’s like it’s glued onto the thing or something