Easy method to set timing on Old Bullet | Royal Enfield 0.8mm BTDC

Hi guys, the above video is all about setting perfect spark time on a Royal Enfield Bullet 350.
Steps to be followed
1. Set the Points gap to 0.4mm at highest opening
2. At compression mode identify the TDC, Set the piston position to 0.8mm BTDC by rotation the wheel forward and backward on 4th gear.
3. Turn the points plate and stop at the position when it starts opening (paper gap), this can be identified by taking ammeter as reference, the needle returns back to Centre when points starts opening.
Note: Handle the scale with care, make sure it wont fall inside the cylinder. To be safer, you can tie the scale with some string by drilling a hole on it.
Regards,
Bulleto

[@syednawaz981]

Such a beautiful lecture on point settings with basic tools, great knowledge hats off bro thank u for the awesome video....

[@shubhamchari8294]

Sir u are best teacher correrty set the point ❤❤

[@vishalmohan1995]

Great video...this would help so many bulleteers. I do this as a hobby myself because every mechanic in my locality messes with the timing like it would be 4-5mm BTDC or ATDC. I use this same method, but instead of bringing the AMP meter down to the points assembly, I attach a seperate indicator to the contact breaker because i have one lying around, I use taper scale becasue it cannot slip into cylinder after a certain length and i would apply 666 paste to the points cover after completing the timing adjustment to make it waterproof during rainy season and it absolutely works!! even when standing in open rain for hours, it would start like a warmed up engine. Old model bullets are so satisfying to work with because of the timeless british design.

[@bulletodiy4548]

Shifted ammeter for reference, I dont use any video editor...

[@bulletodiy4548]

Thank you ✌

[@jatingediya7236]

Make a video on it sir

[@avinashyermal]

Very well explained with proper details! Thank you very much! Looking for much more short videos like this which will help beginners..

[@bulletodiy4548]

Thank you 👍

[@vikramg5518]

You videos are the best...I thought of calling you to speak to you..keep up the great work

[@flaekingr5109]

Perfect, thank you! And thank you for the English, it was very helpful👍🏼

[@prasadmagal7246]

👌👌👍 very clear and simple explanation, deserves a pat.🙏

[@andreascarlberg3998]

Greate advice, sir! Thank you very much! Best wishes from Andreas, Sweden

[@bulletodiy4548]

Thank you, welcome ✌

[@harikrishnap5312]

Very well explained brother. Thanku

[@vishnudaz6864]

Perfect work bro

[@aadhisridhar9595]

Thank you brother very nice and informative.

[@suruagrawal8402]

The rear bullet guru..Original point setting..❤❤🙏🙏

[@honeyy7495]

Godfather video man 🙏🏼

[@bulletodiy4548]

Welcome

[@vijaykumarbanne1457]

ತುಂಬಾ ಧನ್ಯವಾದಗಳು ಸರ್ ಕನ್ನಡದಲ್ಲಿ ತುಂಬಾ ಚೆನ್ನಾಗಿ point setting ಬಗ್ಗೆ ವಿವರಿಸಿದ್ದೀರಿ

[@bulletodiy4548]

Thank you

[@jobinmathew7560]

Well explained. Thank you

[@bulletodiy4548]

Thank you JOBIN

[@niteshkumarmishra3873]

बहुत बढ़िया वीडियो

[@samarthautomotiveservicesr4599]

Very nice information 👌👍

[@aijazqureshividhayakpratin935]

Nice bro ❤

[@promechanic1172]

thanks for your help keep it up

[@bulletodiy4548]

Welcome

[@sravansamrat8246]

nicely explained

[@lightningbeast6674]

Thank u very much anna

[@parthagowda6869]

Thank you ❤ sir

[@swapanjyotikalita6940]

Excellent explanation. Brother, can you please make this video in English so that we can understand it better?

[@bapujiarcot1183]

Good explanation. Please explain other things like clutch cable fixing etc.,

[@bulletodiy4548]

Sure Sir

[@KrishnaPrasad-er7di]

make more videos like this

[@shibunatarajan7579]

Thank you very much bro

[@bulletodiy4548]

Welcome

[@hajeemohammed9912]

🙏🙏🙏 💐💐💐💐 👌🏻👌🏻👌🏻👌🏻👌🏻 SUPER VIDEO THANK YOU SO MUCH SIR 👍🏻

[@bulletodiy4548]

Welcome

[@mokthiyarbashask4076]

SIR VERY FINE

[@satheeshvk9875]

Good 👍

[@moamzong3569]

Very we'll explained Anna

[@The_Twins_Work]

Good job 👌👌👌👌

[@bulletodiy4548]

Thank you

[@MUNDODIVLOGS]

Very nice video 🙌 where are you located?

[@mohanck8719]

Thanks

[@bapujiarcot1183]

Please tell me why during heavy downpour, the old bullet stops. It starts after rain stops and few kicks. Any solution?

[@bulletodiy4548]

Ensure water doesnt enter/ touch the spark plug adapter area and ignition coil terminals... water moisture will cause spark leak/earthing issue... For clarity you can contact me on 6360703486

[@jatingediya]

Sir i can’t adjust point plate bcoz when piston rich at tdc it showing fully retired position how can adjust?

[@bulletodiy4548]

Dismantle the contact breaker assembly, and reset

[@thomasts5002]

Supper

[@onkarkalsi3694]

Super

[@shibink3416]

🎉

[@user-ds5zb8ww9l]

ಸೂಪರ್

[@paavammalayali3957]

Very well explained, Super 👍🤝❤️ Where is your work shop location,

[@bulletodiy4548]

No workshop. Located in Udupi/Mangalore. I do it has an Hobby 👍

[@paavammalayali3957]

@@bulletodiy4548 Ok dear, in another video asked about a tool pl. Reply Me toi as a hobby doing things with my RE.

[@bulletodiy4548]

@@paavammalayali3957 Have replied on the same comment pls do check..

[@Paul630sqdrn]

Does that apply to the 350 and 500 bullet?

[@bulletodiy4548]

Yes its same for 350 and 500 cc std bullets

[@Paul630sqdrn]

@@bulletodiy4548 thank-you sir.

[@Paul630sqdrn]

One further question does that apply to UK models like my 1959 350?

[@bulletodiy4548]

@@Paul630sqdrn this method is applicable for the Bullets having Distributor assembly.

[@msharief6273]

What happens it it's at TDC ?

[@bulletodiy4548]

It will be in retarded position/late spark and overall performance will be less. Thank you

[@msharief6273]

@@bulletodiy4548 thank you sir.

[@anuppardeshi3910]

Sir u had explened it very well but I can't understand Tamil so please explene it in English or Hindi it's my request to you

[@bulletodiy4548]

6360703486

[@Rajesh-pq7zy]

Sir while keeping point Gap the piston should be in BTDC?

[@bulletodiy4548]

At 0.8mm BTDC, point should start opening from closed position

[@Rajesh-pq7zy]

@@bulletodiy4548 thank u sir

[@Rajesh-pq7zy]

Then y we should measure with scale sir ?

[@bulletodiy4548]

@@Rajesh-pq7zy scale is used to identify piston TDC (Top Dead Center) and move the piston position back to 0.8mm BTDC (Before Top Dead Center).

[@Rajesh-pq7zy]

@@bulletodiy4548 sir u can put separate video for how to measure the btdc level because I can't understand properly

[@balum8725]

Better to set timing with 12.7 mm to 9 mm before TDC with full advance by expanding the centrifugal auto advance unit and locking it with something..because measuring 0.8 mm will not be accurate with a scale..

[@msharief6273]

Surely, this will not help

[@user-vj8hq4zl4t]

🫡

[@JK-jo4gp]

Sir wr r u frm

[@bulletodiy4548]

Mangalore/ Udupi

[@JK-jo4gp]

Kk i thought ur in Bangalore

[@JK-jo4gp]

Super sir

[@nasifnazeer1337]

Bro where is ameater connected

[@bulletodiy4548]

For reference, to cover up in single frame, I have pulled a line by disconnecting existing ammeter

[@lightningbeast6674]

@@bulletodiy4548 I also did the same anna

[@msharief6273]

You can also connect any 12v bulb( use indicator or meter bulb with holder) in series at point, one end on body and another end at point wire bottom.

[@indrajitlpk4374]

I think the scale you are using is in cm not mm

[@honeyy7495]

Dont text without knowledge

[@ramakrishnegowdatr4888]

Super demo sir nemma cell no Kodi Sir,🌹🇮🇳🌹 VANDHEE MATHARAM 🌹🙏🙏🙏

[@user-ds5zb8ww9l]

ಇನ್ನಷ್ಟು ವಿಡಿಯೋ ಹಾಕಿ

[@sdigitize6006]

There are alot of trash video, but here is tru work That is 7. 2 tdc or 8.2 you said?

[@bulletodiy4548]

Thank you Sir. Its 0.8mm BTDC at compression mode

[@bulletodiy4548]

Scale is used to identify the Top dead centre and 0.8mm Btdc. The scale what I used points at 7.2mm(reference value in my scale) is piston TDC

[@yadvindersingh1975]

Sir explain it in Hindi or English please

[@shivakumarshivu2160]

Sir ನಿಮ್ಮ ವರ್ಕ್ ಶಾಫ್ ಅಡ್ರೆಸ್ ಕೋಡಿ ಮತ್ತು ಫೋನ್ no ಕೋಡಿ ನನ್ನದು old bullet ಇದೆ ರಿಪೇರ್ ಗೆ ಬೇಡಬೇಕು

[@vinodkaliyamoozhy1969]

Nimth garege yelli irothu? Nimth watsap number kodi. Naniku swalpa maathaad beko.

[@bulletodiy4548]

6360703486

[@onkarkalsi3694]

Very good job

[@onkarkalsi3694]

You r great

[@onkarkalsi3694]

You are great

[@ajaymundlia431]

Bhai ji Hindi me bol ke btao plz