Explaining how to remove and install an input shaft on an Eaton-Fuller transmission.
Пікірлер: 37
@nelsonlopez88042 жыл бұрын
Man this video is super helpful thanks 💪🏻💪🏻💪🏻 I hope you made more videos like this
@darwuinzabala37902 жыл бұрын
Excellent video, very detailed. Thank you!! please one more video with the complete disarming of the transmission. 🙏?
@wildwombatindieseltrucks97823 жыл бұрын
Now do this on a trans with 500k miles covered in grease and grime without removing the bell housing
@firsttimediesels6289 Жыл бұрын
Pull the bell do the gasket, every part in that kits getting used.
@wildwombatindieseltrucks9782 Жыл бұрын
@@firsttimediesels6289 so your going to reseal the aux section that comes in the gasket kit
@itsmisterchris3 жыл бұрын
Nice video thanks.! Do you take out the gears and time them ? Could you do a detailed explanation video on how to time the gears.
@alir53163 жыл бұрын
Awesome video bro appreciate it make more videos like that thank you for everything
@jorgeenriquezambranotinjac54472 жыл бұрын
Soy de Colombia es buena enseñanza que nos dan yo ase 20 años que manejó y siempre me a gustado la mecánica
@illidan2ify2 жыл бұрын
Air regulator, air hammer and blunt bit. It will put that input bearing in in 3 seconds, no damage at all. I've seen them bearing installers break those input bearings.
@camarowilson32732 жыл бұрын
? If shaft is leaking what I'm I replacing is there a seal or I'm i just replacing gasket with bolt holes thanks
@helderhenoch36983 жыл бұрын
Boa noite daqui de Portugal gostei do seu vídeo parabéns muito profissional espetácular um grande abraço para você obrigado Hélder Henoch
@lancelotmasunda18033 жыл бұрын
Good one brother
@donaldtrumps2912 жыл бұрын
I've fought to get those bearings off because I didn't have a puller. The easiest way I found was I got a peice of cable from and old air tank drain valve,. Pull the bearing out wrap the cable around the shaft and smack it in with a hammer, pull back out wrap more cable
@user-dh3ut9ut7w6 ай бұрын
great idea, thank you
@Chris-kq7ko3 жыл бұрын
i like the music. great video.
@codymoorehead5459 Жыл бұрын
Awesome music
@brandonlebeck4233 Жыл бұрын
What is the kit number for the tool?
@tshaunscales5252 жыл бұрын
How can you tell when it needs replacing?
@RussianSupaPowa4 жыл бұрын
no more music, hard enough to hear you talk as is.
@maxuson46162 жыл бұрын
you forgot the gasket for the input shaft kit
@stanluk4618 Жыл бұрын
DONT TRUST THIS ONE. There was supposed to be a spacer outside the snap ring #1 on Input shaft.
@eddiebartholomew9172 Жыл бұрын
Lmao no you are wrong no spacer it’s a fro metric transmission… it does not take a spacer.
@aquamon13393 жыл бұрын
Reverse steps are not rewind but reverse video, LIKE BUTTER MuThaFuKKaH! Hahahahahaa
@Riggafatdog5 жыл бұрын
2 snap rings, and you're not bleeding? Thats not right. You did it wrong.
@mattmcneice7223 Жыл бұрын
no need for that tool, if you've managed to get the bearing top pop out that far on its own, you've already won!
@donhopkins15952 жыл бұрын
Wheres the spacer
@Dizzwayne Жыл бұрын
My thoughts exactly 😮
@rwbborn4 жыл бұрын
Less music
@davidbell70912 жыл бұрын
7:00.. how to ruin a good bearing 101..
@antonmicallef14943 жыл бұрын
Tooo long til vid starts
@howofasttransmission51183 жыл бұрын
Engineering
@davidfs.62333 жыл бұрын
Music sucks..Trying to listen what tech has to say..Hmmmm.next