Tap to unmute

Install Input Shaft on Eaton Fuller Transmission - I Wish I didn't need to open up the top cover 😢

  Рет қаралды 12,734

Idle & Emission Solutions

Idle & Emission Solutions

Күн бұрын

Пікірлер: 18
@truckingandfixing
@truckingandfixing Жыл бұрын
Connect with me on Instagram: ►bit.ly/3C7hRy6 where I will share our shop updates, daily truck repair stories, bite size education clips and giveaways annoucement, etc... See you there!
@mgakowski
@mgakowski Жыл бұрын
Anytime you remove the shift bar housing you need to remove the hi low slave bro. Sometimes that interlock pin doesn't come out with it either, just make sure it's out the way before you refit the cover, then you refit the slave/pin.
@mattdeckert6150
@mattdeckert6150 4 ай бұрын
4:00, I've done 1000's of these with an air hammer, VERY lightly feather the trigger with a bit that is ground flat on the end. Entire front bearing/input replacement in about 10 min with zero damage.
@mattdeckert6150
@mattdeckert6150 4 ай бұрын
I NEVER take the top covers off to swap input shafts on this style trans.
@eddiebartholomew9172
@eddiebartholomew9172 Жыл бұрын
Never seen someone install input shaft retainer without silicone
@banzaii6285
@banzaii6285 Жыл бұрын
Love the longer repair vids, but....I know you're trying to run a business (not a school), and it's probably a pain to record. Thanks👍.
@truckingandfixing
@truckingandfixing Жыл бұрын
Thank you! It is more difficult to record the longer videos! But we will make it work!
@rickysons6362
@rickysons6362 Жыл бұрын
Just wanted to know if pdi turner worth getting
@benjanos5580
@benjanos5580 3 ай бұрын
When that happens w the bearing i hold the input shaft and pull out at same time/ then i hit the bearing inner race to drive it in all the way
@edwardreyes6867
@edwardreyes6867 Жыл бұрын
When the bearing is seated and the input shaft is too far in and the snap ring groove is covered like that, I smack the input shaft with my palms side to side and it’ll work the input shaft and bearing out a bit so I can give the installer tool some more hits. Repeat a couple times and it’ll drive it in properly. Wont have to remove the top cover.
@josevaldez7281
@josevaldez7281 Жыл бұрын
That dodge @ 12:30 tho 👌🏽😂
@BoostedOnaBudget5
@BoostedOnaBudget5 Жыл бұрын
I hold and pull the shaft towards me while sending the bearing in with a hammer or mallet till you can see the indentation for the snap ring
@Rightchuare
@Rightchuare 3 ай бұрын
I do the same thing but only with a rubber mallet
@BoostedOnaBudget5
@BoostedOnaBudget5 Жыл бұрын
Send it with the rubber mallet that top cover did not have to come off!
@eddiebartholomew9172
@eddiebartholomew9172 Жыл бұрын
Lmao why did you install input shaft you can see the hub for overdrive and main drive gear is rolled to death gonna be jumping out of gear. It’s need to be rebuilt.
@BoostedOnaBudget5
@BoostedOnaBudget5 Жыл бұрын
That installer wasn't it lol
@xlxyetixlx
@xlxyetixlx Жыл бұрын
a cheap needle scaler from the usual scum bags would make quick work of cleaning the dirt and rust off the top cover then just blow it off
@banzaii6285
@banzaii6285 Жыл бұрын
"From the usual scum bags" 😆
How to Remove Input Shaft on Transmission - Step by Step
14:05
Idle & Emission Solutions
Рет қаралды 14 М.
Ten speed transmission leaking air from valve on the top and why. Eaton Fuller Fro16210c shift top🥹
7:39
ETR Truck Center | Engine & DriveTrain Specialist
Рет қаралды 14 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН
黑天使只对C罗有感觉#short #angel #clown
00:39
Super Beauty team
Рет қаралды 36 МЛН
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
Fuller Roadranger input shaft replacement
6:54
Don Smith
Рет қаралды 239 М.
input shaft removal and installation of an Eaton Fuller 10 speed
11:46
DragRacer BehindACamera
Рет қаралды 185 М.
DESARMANDO CAJA DE CAMBIOS 14709 FULLER / #UciTomafuller
6:56
TOMAFULLER
Рет қаралды 65 М.
Eaton Fuller Ultrashift Plus 10 Speed: Problem/Solved.
2:37
Lionsdejudah
Рет қаралды 90 М.
How to Rebuild a Main box RTLO 16913A 13 speed
29:22
L & L Transmissions
Рет қаралды 48 М.
Clutch Operation Explanation using a Clutch Cutaway Trainer
11:25
Transportation Heavy Equipment Tech
Рет қаралды 69 М.
Input shaft removal and install
6:09
Brandon Reichenbach
Рет қаралды 78 М.
Ремонт КПП SHACMAN Часть 2
33:48
Спецавтотехника СТО
Рет қаралды 838 М.
Eaton transmission and clutch removal
10:25
Valeriu Moscalu
Рет қаралды 236 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН