Echo SRM 225 String Trimmer Won't Start - Flooded

[@aarondavis8734]

Two years later, and this video is still getting weed trimmers started! Bought mine today and promptly flooded the engine, this worked perfectly.

[@Future9]

OMG same

[@DHD-z40]

Same lol u

[@dylaninterval6355]

Me too! Haha

[@nicsincompletelibraryofsou5496]

Me as well 😅

[@mccglastron1972]

This is the BEST Echo trimmer start video! She describes the issues EXACTLY! Her start procedure at 2:50min works 100%, THANK YOU! I was getting pissed off... I bought this thing because it was supposed to be easy to start! It's unreal their manual's instructions make the product look bad! Works perfectly now thanks to her advice! I'm gonna post a link to her vid on the other vids that were close buy not quite as good.

[@Know-How-Now]

I also made a video on how to change the trimmer line. You might find that helpful too. Here's the link to the video: kzbin.info/www/bejne/bJuUaqiOe7l4adU

[@marktaylorauthor1000]

I switched out my air filter but I also did what you said and it started right up. Thanks! Literally the first time in 8 years I couldn’t get my echo to start

[@paulwosny]

Was ready to take it back to the store. Bought it brand new and was very difficult to start according to directions. Haven't had a problem since watching your video

[@descalante8282]

Your method to clear the flooded engine worked flawlessly thanks 1 million. I was getting a little frustrated as I just purchased this and it took me two hours to just trim the edge of my grass which would’ve taken me 10 minutes if I refuse my electric trimmer to begin with. But you live and you learn thanks again

[@Know-How-Now]

You are welcome. Thanks for taking the time to comment. I always enjoy hearing from people who watch the videos. So far the only complaint I have about the trimmer is the incorrect starting instructions.

[@AnthonyGlass-dh6dm]

😊

[@alhardie8277]

Thanks saved me a lot of frustration I was almost going to buy a new carburetter kit off Amazon

[@Stmpjmpr01]

Totally agree! It was flooded and I was so frustrated. Did this method and bam we were good to go. Thank you!

[@ekriesch]

Thank you! Like many others who posted, I followed the directions and couldn't get it started. I figured it must be flooded, but couldn't fathom why the directions led me down this path. I was beyond fed up and no other videos I found helped. I followed your directions to move the lever to run and pulled about 15 times and started right up. Very clear and easy to follow - thank you for taking the time to make this.

[@Know-How-Now]

You are welcome! There are many comments similar to yours. It's hard to believe that Echo could get the starting directions wrong. I do like the trimmer.

[@FC-cz6zd]

After retiring my wonderful Husqvarna, I picked this one up. Flooded the carb. Thought 8x was excessive but I was obedient to the instructions. Thanks!

[@Know-How-Now]

I too followed the instructions thinking this isn't right. I called Echo and their tech support rep didn't agree with those instructions either. I am still scratching my head at how those instructions can get sent out with the trimmer. Although, I just pulled my toilet to troubleshoot a possible clogged trap. I bought a set of nice brass bolts from Ace Hardware. After setting the toilet on the wax ring, I couldn't get the nuts on the bolts. I figured out that the threads on the bolts don't fit the nut that came with the bolts! Agh! Total PITA. While I am ranting. I just installed a new over the range microwave. The holes on the template for the bracket were wrong. Luckily I caught it before I drilled holes in the wall. BTW I love the trimmer. I am running Trufuel in it. The mechanic at the mower shop recommended it. He said it will save money on maintenance. I don't think he was trying to sell more product because he told me to look for it at Walmart at the end of the season. They mark it down. I got 2 years out of one of the big cans.

[@jimcarmichael4848]

The pulling 15-20 times to clean out a flooded engine worked PERFECTLY! THANK YOU!!!!

[@Know-How-Now]

You are welcome!

[@LUV1906]

It worked, thank you! I could say more, but many have communicated my sentiments. New trimmer - 3rd time using. Would not start this morning in warm TX weather - at all. No sputter. Fuel is good, if not, I blame Echo. It's their brand 50:1. I grew frustrated after trying on my own for 20 minutes. Decided to mow my lawn anyway before work. 8 hours later, I stumbled across your video with a quick internet search, and it made the world of difference. Full disclosure, I selected it due to it being the shortest tutorial. You weren’t exaggerating with 10-15 pulls. I exceeded that twice over, likely due to user error. I cleared the flood, edged my front and will return to weed eat. In closing, THANK YOU!

[@Know-How-Now]

You are welcome. I try to keep the videos as brief as possible, but still informative. I hope the weeds were tasty! lol. Thanks for commenting. Have a great day.

[@benjaminlarson7292]

This video changed my entire life 🎉 thanks for sharing this info for flooded start 🎉 … I’m going to go live my new better life now 🎉

[@Know-How-Now]

Wow! Have a great life.

[@gg3947]

I couldn't get my Echo to start for 6 months. Basically stopped using it. This video got it working. Thanks!

[@Know-How-Now]

You are welcome. I really like mine. In a few days, I expect to post a new video on how to load new string. It's really easy. I love it.

[@ligeng8079]

I was ready to give up and return the trimmer. Luckily I came across your video! Thank you so much for sharing.

[@Know-How-Now]

You are welcome. If you haven't had to replace the string, I have a video that shows how to do that. kzbin.info/www/bejne/bJuUaqiOe7l4adU

[@jimmyjames7789]

Your video was a lifesaver! Was on my second brand new echo trimmer and could never get it to start. Following your directions got it started and can restart easily! Thanks!

[@Know-How-Now]

You are welcome. Other than the incorrect starting instructions, I am very satisfied with trimmer. It's a breeze to refill the line. Here's a video I made that shows how to do it: kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=NPYIX-4KPjICR382

[@johnvogel1150]

Amazing, worked perfectly. Tried to start the dang thing for 2 hours before finally seeing this. Got it started 15 seconds later

[@jasonwu6564]

I followed your instructions and restarted my Echo. It saves me CAD$100. Thank you so much.

[@Know-How-Now]

You're welcome.

[@Crymsyne]

Thank you!! We just bought one and couldn't get it to start. Your video fixed that.

[@Know-How-Now]

You are welcome! It's a good trimmer. I am satisfied with mine. I don't know why they have not fixed the starting instructions.

[@mixedmakingsbyamanda1204]

Thank you so much! We rented a brush trimmer for the day with the same motor set up and were getting so frustrated because we were following the directions. It started right up when I followed this video.

[@Know-How-Now]

You are welcome. It's good to hear the video solved the problem.

[@billnotice9957]

WOW! How helpful. Never imagine I could start it in non-start position when warm. Wasted half the day. Took a 5 minute break that turned into 3 hours. I watched your video when right out and wham. Off the Subject. I put the renagade brush cutting blade. OMG does it cut brush.

[@mr.wonderful7479]

Thank you! I have Echo SRM 2620T, would not start, and keeping the choke off in down position helped get it started, after like 15 quick pulls. I normally do not press the primer bulb if using weekly and I normally have choke in up position till it sputters, then push it down and it starts.

[@carolynmilhiser3478]

Thank you! Totally saved me. Rented a hedge trimmer from home depot so only had it for the morning. Would never have figured it out if it wasn't for this video.

[@Know-How-Now]

You are welcome, Carolyn.

[@natashar2883]

Got a great deal on this trimmer and almost returned it. So glad we watched this video first!

[@Know-How-Now]

Other than the poor starting instructions, I am pleased with the trimmer. Replacing the line is a breeze. I have a video that shows how to do that. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=aKrmkF4Vi9eraFFe

[@carolstrobelberger1834]

Hi. I reviewed the Echo Quick Start manual that came with the trimmer and the more extensive manual on line finding nothing useful at all to help me understand why the trimmer wasn't starting. I knew I had the correct gas octane and the right oil and ratio of gas to oil. After exhausting many websites to no avail, I came across your KZbin instructional. I followed your starting instructions & how to clear carburator KZbin video. After following your instructions, my frustration melted away and I was thrilled. Thank you so much for your specific "flooded" video--the trimmer started right up!!! I will be viewing your other videos as I like to, "Know How Now".

[@Know-How-Now]

It's my pleasure to help, Carol. Thank you for taking the time to comment. I like to hear when the videos have been helpful. Have a great day.

[@MikeRich912]

Your are a blessing! I was so frustrated after following all the directions to Tee, putting in my diamond blade trimmers in all of the other things mention only to not be able to trim my yard due to what I now know is the engine being flooded with fuel. In South Carolina where the weather is 90° and rising by 8:30 AM. I was super frustrated. Thankfully I came across your video salute and thank you.🚛💨🔥

[@Know-How-Now]

You are welcome. Stay cool!

[@deanfletcher8284]

This video saved my afternoon. I finished mowing and picked up the trimmer, and basically had the same experience described by mccglastron1972, with the same emotional response...looking for a pine tree to wrap it around lol. I came in and searched KZbin and found this video, and in about 10-15 minutes was back in business. Thank you Know How Now!!!!

[@Know-How-Now]

You are welcome, Dean! Thanks for taking the time to comment.

[@NganNguyen-m4u3q]

You are the best! After changing the spark plug, air filter, fuel lines. I couldn’t get it to start so I gave up and while laying down and thinking about it I stumble upon your video and this worked. I literally had to pull 15-20 times on switch to run since I think I pump the carb with too much fuel. Now tomorrow I can trim.

[@Know-How-Now]

You are welcome. It's good to hear the video solved your problem. Happy trimming.

[@Carlos-nz3vi]

This worked! I have a GT-225 and I thought the issue was the fact that I haven’t used it for over a year

[@mikehughes8023]

2 year old vid still relevant today! Thanks👍🏿

[@Know-How-Now]

You are welcome.

[@michaelflacco4303]

What a great video. Thank you, I was going to return my Echo thinking it was broken. Your video explains everything in detail.

[@Know-How-Now]

You are welcome. I still have the trimmer and have no complaints other than the wrong starting instructions that come with it. The other thing you'll need to know is how to install new line. I have a video that shows how to do that. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=0fgSi20Zwtjij5H_

[@hcooper267]

Thank you,I been trying to start my echo for one month and I followed your instruction and finally start. Thank much.

[@Know-How-Now]

You are welcome. I just made a video on how to change the line. You might find that helpful, here's the link: kzbin.info/www/bejne/bJuUaqiOe7l4adU

[@WestalSage]

Yep works great - I've learned to press that primer bulb like 3 times max for a cold start. Really just watch the fuel line and only use the bulb to get a bit of fuel into the line.

[@goddessinaritaoist2970]

omg!! Lady I did this just like you said and furiously yanked on it and it worked HA! I love you!! I was just yanking really hard oneor twoo times on cold start after only priming it 4 times. I didnt realize you had to do it hard n fast Hrmmmmmm Hee hee

[@williampfahl5758]

Thank you --at --2:29---- How to clear a flooded engine! this worked for me. Love your voice rhythm and careful word choices, easy to understand.

[@Know-How-Now]

You are welcome, William. I do my best to make quality videos.

[@johnedwards9338]

Thank you! Like everyone else here I followed the instructions and flooded it. Thanks for the fix!

[@Know-How-Now]

You are welcome!

[@matthewvarela9540]

Best echo start videos out there thanks we all followed the starting procedure just to not start thanks got me yard workin right after video

[@Know-How-Now]

You are welcome, there is also a video on how to replace the line. Here's the link: kzbin.info/www/bejne/bJuUaqiOe7l4adU Thanks for watching the video and taking the time to comment. I love to hear from the people who watch the videos.

[@brianmoore3063]

Cleared the fuel lin, cranked right up. Thanks cuz 🍻

[@21deangelo]

Actually worked thank you and not a long a drawn out video

[@Know-How-Now]

You are welcome. I try to keep the videos as short as possible.

[@nancymedina5314]

This video was super helpful couldn’t get my echo to turn on! Turns out I flooded it! Awesome info easy to follow!

[@Know-How-Now]

You are welcome Nancy. Have a great day.

[@francoalfaro7750]

LOVE THIS TYPE OF VIDEOS!!!!! THANK YOU 😊 Now, does anyone know how to clear/clean the overflow fuel on the carburetor or exhaust?...

[@2aminitials]

1:43 It did start on the third pull but died due to the choke being on. That is normal. Once the engine fires stop trying to start it with the choke on. Move the choke lever to half choke or off. If you don't you'll flood the engine. Also you can push the purge bulb as many times as you want to. It is not a primer bulb in the sense that it adds fuel the the engine. The purge bulbs purpose is to bring fresh fuel from the fuel tank to fill up up the metering chamber of the carburetor. The second fuel line connected to the carburetor is the return line where excess fuel in the metering chamber of the carburetor goes to be returned to the tank.

[@Know-How-Now]

Hi there, thank you for the thoughtful and helpful comment. I think you may not have watched the entire video. In the beginning of the video, I am flooding the engine on purpose by following the quick start guide that comes with the trimmer. Then showing how to start it if is is flooded... which is likely to happen if you follow the instructions. The guide does not tell you to move the choke lever to half or off as you noted should be done when the engine sputters/fires (correct thing to do). Later in the video I show how to start the engine without flooding it. I don't know why Echo would include only a quick start guide with incorrect starting instructions. I wondered why there was a return line for the fuel... thanks for the education.

[@2aminitials]

@@Know-How-Now I agree with you on the quick start guide being incorrect, and you do explain the starting procedure very well in the later half of the video. ECHO needs to hire you to make their instruction sheets instead of the people they have doing it now.

[@Know-How-Now]

It's a head scratcher on how an incorrect quick start guide could be the only instruction that comes with the trimmer. I reluctantly followed those instructions and flooded it. My previous string trimmer was an old Cub Cadet. It had the craziest starting proceedure, so to me having instructions that go against common sense didn't stop me from following them. I did call Echo's tech support and read those instructions to them. The guy I talked to was quick to say pushing that bulb 8 times was too much. I downloaded the user's manual and the starting instructions are correct. Hopefully the video will help anyone using those quick start instructions.

[@2aminitials]

@@Know-How-Now Like a lot of things today the quick start was probably wrote / designed by someone with book smarts and no real world experience.

[@Dani-blue]

You saved me!!! Flooded the engine and was about to throw it over the fence lol. Your instructions worked and got me going. Thank you!!

[@Know-How-Now]

You are welcome!

[@alanapatten2778]

Super clear, to the point and HELPFUL. Thank you!

[@Know-How-Now]

You're welcome!

[@numberformat]

The gas looks super clear as well is that 1:50 mix?

[@jimmyrumney4379]

Holy cow. Do this once and it started. Thanks!!!!

[@Know-How-Now]

You're welcome!

[@3rdgenbestgen21]

Thank you so much. i though i bought a lemon but after this video, 1 hour later my backgyard is done. It’s been since 2012 the last touch anything to mow a lawn. Lol.

[@Know-How-Now]

You are welcome. Other than the wrong starting directions that came with the trimmer, it's been perfect so far.

[@3rdgenbestgen21]

@@Know-How-Now awesome i look forward to use this for years haha

[@liaison66]

I just flooded mine yesterday. thanks for the tip!

[@Know-How-Now]

You are welcome.

[@kenelledge3299]

Best advice ever! Thank you so much for sharing how to clear a flooded engine. 😊

[@Know-How-Now]

You are welcome.

[@thenextchapter3615]

Thank you, this methods works!! Also, please add how long you let it sit before retrying

[@Know-How-Now]

You are welcome. KZbin won't allow me to add to the video. You might let it sit for a couple of hours. The time could vary greatly on the outside temperature. By pulling the cord, you are creating air flow and drying it out.

[@jessej.nelkie5978]

Great tutorial. Came in handy. Thank you very much!!

[@Know-How-Now]

You're welcome!

[@jpvet5411]

Recently bought a brand new Echo and they still have these same dumb instructions. Thank goodness I found your video. 👍

[@Know-How-Now]

Wow, it's hard to believe they have not fixed the instructions. Other than the poor instructions, I like the trimmer. If you haven't filled the line yet, it's easy. I have a video that shows how to do that. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=lq1Km4FY_0jtChbp

[@johnpwrites]

Excellent work on this video. Very helpful! 🙂

[@JohnTurner-bd1of]

Man your method works my weed eater started right away

[@bulldawg71199]

Super easy fix just didn’t know exactly what was wrong. Thought I was getting the half and half gas and water mixture wrong but clearly that wasn’t the problem. Cleared engine of excess oil and was able to finish the rest of my yard. Thanks

[@Know-How-Now]

You are welcome.

[@johncollins8304]

@@Know-How-Now "half and half" ?? Gas and WHAT??

[@johnboy7029]

Finally no gimmick!!!! this video actually works

[@digitalnorm]

At minute 1:39 as you are pulling the starter you can hear the weed eater fire. At that point the choke needs to be opened back up to the run position and then the engine would have started on the next pull or two. The reason it didn’t start is that although it had started to fire, you kept the choke closed.

[@Know-How-Now]

You are correct, Noah. The start directions that come with the trimmer do not tell you to do that. I am demonstrating what happens when the quick start guide instructions are followed... and likely what someone would do who doesn't have the same level of knowledge as you do. Later in the video, I show how to start it correctly..... maybe you didn't watch the entire video? Many don't.

[@bulletquest]

Fixed my issue with a new string trimmer

[@RamiroGarzaJR]

Thanks for the video. Got my new one to crank after watching this.

[@Know-How-Now]

You are welcome, Ramiro.

[@rolandoolivo87]

Thank you. I also followed instructions. I was about to take it back.

[@Know-How-Now]

You are welcome. I've used the trimmer for 2 seasons now and am still pleased with it. I have a video showing how to fill the line. It's a breeze. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=hJyDociDdqajAR6x

[@aaronkarcher4503]

Thank you for this video. I was beating my head against the wall. I flooded the dang carb following the directions…🤦🏻

[@Know-How-Now]

You are welcome, it's my pleasure to help. I also just published a video on how to load new string. Here's the link: kzbin.info/www/bejne/bJuUaqiOe7l4adU

[@joedove6933]

Thanks for your video, I was this close to just binging the thing back to the store

[@Know-How-Now]

You are welcome. I have a video that shows how to replace the line. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=8Xe_YRfiXj3QD65I

[@sheri023]

It's that time of year, isn't it. I'm getting out my high wheel trimmer that's been sitting for years. Good luck and have fun with your new weed trimmer.

[@Know-How-Now]

Yes, the grass is greening up and growing. So far the trimmer is way better than the Cub Cadet I had for 20 years.

[@DSPEREZJR]

Thank you so much! Wasn’t able to start this damn thing in weeks. Your video got it going. Thanks friend !

[@Know-How-Now]

You are welcome! Have a great day.

[@davidwilliams5957]

Thank you for this video. It’s 100% accurate.

[@Know-How-Now]

You are welcome, David. It's my pleasure to help.

[@pimpim.1gov]

Just tried this. It works

[@Miguel762-40]

Thank you so much for your help! 🙏🏼

[@Know-How-Now]

You are welcome.

[@stevep2325]

TY, you were the only video that helped me. wish I could give you a hug 😘

[@Know-How-Now]

You're welcome!

[@brittanislarp3850]

THANK YOU SO MUCH. THIS WORKED A CHARM FIRST TIME. 🎉

[@Know-How-Now]

You're welcome!

[@randyluu283]

Thank you so much for your great video. It helped me to fix my Echo SRM 266 !

[@Know-How-Now]

You're welcome!

[@JTskates]

Worked like a dream definitely not fake

[@OCHOSTE]

Thank you after watching the video and tried,it worked ❤

[@Know-How-Now]

You're welcome. Good to hear it worked.

[@Asquaredbastards]

Thank you for helping troubleshoot a lot of frustration !

[@Know-How-Now]

You are welcome, Adam!

[@kenl4632]

Thanks for your KZbin! It saved my afternoon!!

[@Know-How-Now]

You are welcome, Ken.

[@kinghootchie863]

Had a new srm 225 that I fueled with the can stuff (94 octane no ethanol) and let it sit outside under a patio cover for about a month. Finally got around to starting it, a couple of pops, then nothing. Tried some carb. cleaner, more pops then dies. So, fuel starved is the problem. Borrowed a small glass jar and drained the fuel tank into it. There was about 3/8" of gas and 3" of water in the jar. Imagine my surprise. Dumped that garbage out, fill it with new fuel and it took off on the second pull. I have no idea where all of that water came from. I don't think it rained the whole time it was outside.

[@danpe8945]

perfect worked exactly as you instructed. thank you

[@Know-How-Now]

You are welcome.

[@jamesclevenger2869]

You’re the best!!! Completely worked. Thank you!

[@Know-How-Now]

You're welcome!

[@WheelHouse1of1]

This worked for me. Almost put this thing on the curb.😮

[@agirlandherdad2483]

Worked perfectly. Thank you😊

[@Know-How-Now]

You're welcome.

[@saulnavarrete1708]

Wow u saved the day for me! Thank you!!

[@Know-How-Now]

You are welcome.!

[@airheads162]

bro thank u so much i’ve tried everything and this works

[@Know-How-Now]

You are welcome.

[@kellbenlewis5270]

Exactly what it was for me. Brand new and wouldn’t start after following the instructions.

[@Know-How-Now]

It's hard to believe that the incorrect starting instructions could be provided. They didn't seem right to me, but my previous string trimmer had the craziest starting instructions, so I tried them and of course it flooded. The world is kind of messed up right now, so I'll give Echo a free pass. So far, I love the string trimmer.

[@kellbenlewis5270]

@@Know-How-Now yes it’s been a beast for me at clearing an overgrown horse pasture fence line.

[@NathanHangen]

TLDR - turn choke to run and pull hard 10-15 times. Worked for me!

[@sniper0625]

Thanks, it's my third day as the sole maintenance guy at my new job and you probably just saved me a fuck ton of embarrassment

[@Know-How-Now]

You are welcome. KZbin has saved me many times. Best wishes for the new job.

[@gustavojimenez7630]

Thank you. Your method worked!

[@Know-How-Now]

You're welcome. I have the trimmer a few years now. I am finding that to start it cold, I can put the selector to "run", pull it and it starts up. I'm not sure what has changed. I haven't done any maintenance on it yet. When I bought it the mechanic at the mower shop told me to run True Fuel in it. He said that running the True Fuel will cut down on repairs. I took his advice and it has been running like a champ so far.

[@Brian-qe3ys]

Nice clear and straightforward. 8 is way too much.

[@Know-How-Now]

I agree. I don't understand how Echo could allow those instructions to be included with the trimmer. Other than those poor instructions, I am very pleased with the trimmer.

[@GilbertoPerera]

saved me a lot of trouble...thank you!

[@Know-How-Now]

You're welcome!

[@samuelgendreau4753]

Thank you help me save me some trouble

[@Know-How-Now]

You are welcome.

[@LilParticle]

You’re a legend I swear

[@Know-How-Now]

I don't know about that, lol.

[@saldoug7467]

Worked like a charm

[@castro918]

Thank you for this video. It started right up.

[@Know-How-Now]

You are welcome.

[@rayrocha9443]

Fixed my issue perfectly! Thank you.

[@Know-How-Now]

You're welcome

[@rafaeltejeda94]

Thank you for your tips

[@Know-How-Now]

You are welcome.

[@larryjohnston5519]

I stopped Watching @ the 2.27 mark and proceeded to do that, IT WORKED!! Oh My Goodness! I was so happy! I wanted to kiss you!! Thank you very much!! 😊👍

[@Know-How-Now]

You are welcome!

[@tmph1814]

You're awesome, thanks a bunch!

[@Know-How-Now]

You're welcome!

[@conradgalvez]

my cho trimmer 225 in morning i leave out in backyard so sun gets to it for about half an hour and starts right up kinda of strange huh because if i try right off the bat it wont start but nice trimmer anyway

[@raymundoovalle1624]

New echo weed eater and won't start. I also used trufuel 50. They told me it was good stuff.

[@Know-How-Now]

I've been using Trufuel in mine since I bought it. A small engine mechanic told me to use this fuel. I've had no problems with the trimmer and am at the end of the 2nd mowing season. I don't know if they are still including the start directions with the trimmer that flood it. If you are sure that you have not flooded it, here are the directions to start it properly. You can book mark video so you can find it when you want to start the trimmer. kzbin.info/www/bejne/jp6woZmthtdkhpYsi=juYLU038Qpx33-xi If it is not flooded and these start instructions don't work, then take it back to the mower shop. I have no complaints about the trimmer other than the poor starting instructions. I also have a video that shows how to load new string... very easy. kzbin.info/www/bejne/bJuUaqiOe7l4adUsi=uWzsqg-ywIN6RKzA

[@yairROBLOX]

liked and subscribed you are a life saver my friend 🙏 was getting ready to return it lol

[@Know-How-Now]

Welcome to Know How Now. Have a great day.

[@TheOLearysNC]

Thank you. Huge help

[@Know-How-Now]

You're welcome.

[@alvarovalladares4754]

You're a goat! 🐐 appreciate you

[@jrjones437]

Great advise

[@cleartouchmaintenance]

Damn,that worked .....thank you

[@Know-How-Now]

You are welcome.

[@BurgundyRedd]

The initial tip worked to get it started but now it wont stay idled, any thoughts on how to fix it?

[@Know-How-Now]

It looks like there are several YT videos on that topic that would be more helpful than me writing a few paragraphs. Do a search for "echo string trimmer won't stay running" that will be way better than us going back & forth.

[@GotSwagBruh]

Worked for me, thank you

[@Know-How-Now]

You're welcome!