Edwards Fire EST3 Replacement Smoke Sensor and Pull Station

Edwards EST3 Fire Detection Systems are able to work smoothly by taking their own address from the CPU when the field elements such as Detector, Button, Module are damaged when they are replaced with new ones. . If your loop line its complete and you havent any problem can you replace any device on your line . Thanks for watching and please like and subscribe !
www.teknik.kz

[@jalalwadood6519]

For those who want to add or delete detectors in 3x panel using 3sdu software Go to configure, then module, then select Loop controller (ssdc or sddc) then click lrm config then loop detectors add or delete detectors from there

[@redwin1]

Sangat menarik untuk dicoba . Tks..

[@rajiibrahem7281]

Hi I have a fire alarm system. Edwards uses a fairly old DOS system, but it works fine but we have a problem. When a warning occurs in a sensor, the alarm comes to the computer screen. The alarm is located but no sound is heard. After you have logged in to the IRC3 program and when you ask for any order or access to the list of commands does not appear and I will send pictures about it please help me and thank you very much

[@raymonddavid7948]

Hi Teknik, what software you are using for configuration of EST3 panel using laptop?

[@jalalwadood6519]

3sdu

[@vishak983]

But I think when we add or replace new device then must have program the panel with new device's serial number???

[@teknikkz4233]

If you need to add new devices , sure need to SDU3

[@elawadymohamed6721]

this case If my loop work good only or what ? this in conventional and addressable or what ? Thanks a lot Prof .

[@teknikkz4233]

You loop must be Complete without any problem . This system is addressable EST3

[@elawadymohamed6721]

this case work well if i changed detector base ? i know Edward system *(est3) but i ask i can replace without programing ? please obtain how can i replace without any programing thanks for your time ^^

[@teknikkz4233]

Your loop must be fine , after this you don't need any program for change what do you want it .

[@vishak983]

@@teknikkz4233 but how can panel read new device's address without program

[@teknikkz4233]

@@vishak983 You cant add new devices whitout 3-SDU .

[@jzaragoza7296]

Replacing a Siga PHS for a Siga PHD, would I need to go into programming at all?

[@teknikkz4233]

Of course you need it because it's different device.

[@jzaragoza7296]

@@teknikkz4233 did it, and the panel learned the device on it's own

[@teknikkz4233]

@@jzaragoza7296 Did you check this sensor working normally or no .

[@maduraperera222]

can you teach how to add new ditectors to loop

[@mkmaurya9432]

Have you programming software 3SDU

[@techfire9978]

When you remove break glass the facp not showed fire signal

[@kalithmohamed1444]

Tku

[@gouseshaik7179]

Can you please guide me how to add sounder on est3cpu directly

[@teknikkz4233]

gouse shaik On CPU top have a First Alarm contacs you can use is for sounder but with service program can not put delay for this contacts.

[@devubarde3395]

How can I add, replaced unprogrammed device with fire control panel. Is programming necessary of devices ????

[@teknikkz4233]

You need to add with 3-SDU can't add w/o software .

[@jalalwadood6519]

@@teknikkz4233 how to remove and add with 3sdu can you explain please

[@thonyperez2040]

What about the address of the one you replace. It will automatically address

[@teknikkz4233]

If its your loop complete yep , but if you have some problems with your loop not possible .

[@naserkhan662]

Dear sir. Today i have replaced 2 faulty detectors. Do i need to programme the replaced device ???

[@teknikkz4233]

If its loop complete before replace you didnt do nothing .

[@mkmaurya9432]

Yes , you need to do programming , have you programming software 3sdu

[@ishmaelkumaku3546]

@@mkmaurya9432 Please how do I do the programming in technician but know little about software we are currently using parsoft at work can please help me on the programming of the replacement of a detector

[@ishmaelkumaku3546]

@@mkmaurya9432 Please this is my WhatsApp contact [phone] I will appreciate if you can help me with this one

[@jalalwadood6519]

@@ishmaelkumaku3546 if you done, help me 2

[@bijinthegreat]

SDU3 programming software. From where can i get this software???

[@teknikkz4233]

You cant download this software .

[@reymondnaquines8110]

My work before in Saudi Arabia est3 edwards

[@teknikkz4233]

Have a nice job Sir .

[@rehanzahid9600]

Hi can i ask some questions in Edwards system

[@veeranarayanachari714]

Hi, Mapping/Programming required or not after replacement of new device

[@mkmaurya9432]

Required program , have you programming software 3SDU

[@veeranarayanachari714]

Yes I have

[@teknikkz4233]

You can check device after replace around 2 mins . Give a smoke and check panel if its not coming true address and getting "Unprogrammed Device" you need to Software .

[@muzamiliqbal2461]

hell sir can i talk with you ?

[@kayantesomby3920]

Kayantesopy du startfire Kayantesopy

[@magedsobhy5376]

Is SDU software support win10 64bit

[@teknikkz4233]

The last one we used, 5.74, doesn't support it.