Make an IR sensor module for Arduino | Proximity sensor by yourself

[@atulmulsha9016]

Thx u ee wave I tried all others but it didn't work but when I tried ur I was just like !finally , one thing that is important if u are making this for hand sanitizer that I made also u have to keep in mind that it will not work with tip32c it will only work with Bc547that is very common transistor

[@paulmeynell8866]

This is interesting for learning but I can but this as a sensor board cheaper than I can buy the components!

[@LUISDIAZ7777]

EXCELENTE AMIGO,ESTE SI FUNCIONA....HE PROBADO MUCHOS MOSTRADOS EN KZbin QUE NO FUNCIONAN PERO ESTE SI.....GRACIAS!!!!

[@EEWave]

Thank you...

[@fdiy8612]

superbly explained Sir, good job! I had an IR module , I attached a 5 vmotor pump to it using a TIP32C transistor, Output from module is attached to base of transistor, VCC 5v from power source & module to the Emitter & positive line from pump to collector, when the current is switched on it makes the pump to run continously , It , however slows down when an obstacle is brought near the IR transmitter / Photodiode, is there something wrong with the IR module? I was trying to make an automatic soap dispenser

[@fdiy8612]

I found the solution to the problem, I realized there are two types of IR module in the market , one with single LED which works well with BC 457 transistor , as shown in your schematics & other with Two indicator LEDS, which works well with TIP32C /TIP 42c

[@MuhammadArslan-qp8xm]

@@fdiy8612 can you tell me how to perform it with tip32C ,should i use same IR of two leds as shown?

[@AvdL769]

I was looking for a simple diagram, but this will not work for me. I want to make an ir light tunnel, but this might not be reliable. What's the problem? Sunlight or some other heat source might be the problem. This gives a dc offset to the ir receiver. So please use a kHz carrier (good old NE555) with the ir led and detect this carrier on the other side. There is a capacitor after the receiver to block dc signals (sunlight). When the carrier is present after the capacitor, there is a signal (clear line of sight of the tunnel). No carrier, then the signal of the ir tunnel is interrupted. That's why ir remotes also use modulation. But thanks for this video. It's nice.

[@jumbo999614]

I added buzzer to the circuit. But the noise the buzzer makes is too low. How do you make loud? I want to install this at the door. So whenever someone walk in, it will make a loud noise. Also why receiver's cathode is connected to positive? This is confusing.

[@satishrajp1934]

nice work bro....but the sun light makes the sensor on...is there any solution to it...

[@prabhat_ranjan]

Very Good Circuit for Arduino. It successfully works.

[@jibiabrahamabraham4211]

Bro where did you connect our pin I am in the final stage of making this pls reply

[@farhad6365]

4:12 what is the gage of the green wire... please tell..

[@archanamulsha7644]

Bro finally really works

[@Berghiker]

In my circuits the negative of both IR LEDS are connected to the positive of the battery to work.

[@jamalayub6290]

Nice Video, Can I use this ir sensor circuit with (12 Volts small water pump) , How to use it? Please tell me.

[@maherdweik2302]

Thank you for the detailed instructions,that really helped.

[@mujtabiralam5016]

What is output voltage from this sensor? Is this sensor makes 0 volt when it gets any obstacle?

[@KarlA-vk4kn]

The output will be Logic 1 (High) or 5Volts when obstacle is detected. If using LM393 OpAmp then the output will Logic 0 (Low)

[@Devil-dn2ew]

Do the photodiode works in forward bias??????

[@Iamsuccesspro]

No. Photo diode or transistor conductivity is yearly increased (resistance lowered when exposed to infrared light) in forward bias it would conduct right away

[@cw4608]

Is there a way to adjust the distance at which the sensor triggers the LED?

[@EEWave]

By adjusting the potentiometer on the circuit, you can adjust the distance. Maximum distance is nearly 25 cm, minimum is 1 cm.

[@harshsaini8795]

Bahi moja ak dout ha ke is ma pump moter kasa lagaya automatic sanitizer machine ka lia

[@anonymousmanavalan9953]

Hey bro nyc video but how can i connect a TSOP38238 instead of photodiode plzz help me🙏🙏🙏🙏🙏🙏🙏

[@IIT2007]

Bro make a video plz how to make hand sanitizer machine using this sensor or else plz tell me can I use this???

[@jaysernal8701]

my friend how about if im going to use 12v relay what should i do? thanks

[@EEWave]

Connect a 10K resistor with the output, other pin of the resistor should be connected to base of BC337 transistor. Connect One pin of relay coil to +12 v. Other pin of relay should be connected to collector of transistor and connect the emitter to the ground. Across the relay coil, you should connect a freewheeling diode.

[@jaysernal8701]

@@EEWave thank you so much for this really appreciated ... i'm a new student thats why im asking... im going to try it now

[@naderhumood]

Great job Sir. ✌️🇧🇭

[@IIT2007]

Can I make hand sanitizer circuit with this circuit?

[@IIT2007]

Bro tell me fast it's urgent

[@veeral__rathod]

@@IIT2007 bhai banaya ??? Tumne ??

[@IIT2007]

@@veeral__rathod ha mast Kam Kara par my mon destroyed as I made it with cardboard na toh unhone bola fungus lag jayegi 😅

[@veeral__rathod]

@@IIT2007 great 😃👍

[@khadijasoomro3519]

is it suitable for counter circuit

[@EEWave]

Yes, I uploaded two counter circuits using Arduino and this sensor. Unidirectional object counter: kzbin.info/www/bejne/Y4q7e3lqa7Ccf68 Bidirectional object counter: kzbin.info/www/bejne/fJvId3eCr6aAi5I

[@khadijasoomro3519]

@@EEWave but i am assigned to make circuit using counter Ic n IR sensor...so for that i wan Clock signal so will it provide Clock signal

[@EEWave]

Yes, it works in the without microcontroller circuit also.

[@khadijasoomro3519]

Thank you.

[@ronaldleon6952]

Hi how can I read the input from the sensor using an arduino micro-controller and light up the seperately LED using code?

[@francisco9427]

Como faço para colocar um relé nesse circuito para ligar um secador de mãos?

[@rahmanocawni5618]

Yes friend. I want 12 m distance if possible

[@Robonova]

Bro, didn’t worked. I changed the receiver, and tried tv remote as transmitter but there was no response... I even changed the ic with new one but it didn’t worked. But when I connected two ends of receiver with external wire the led glow... help me and reply ASAP.

[@atulmulsha9016]

It works perfectly it's ur mistake while making

[@boybravo689]

Sir may i know if that circuit is good for testing remote control and the infra red led are different from photo led? tnx much sir

[@EEWave]

Ya, you can check your IR remote with it. Actually the black one is photo transistor. Some people says it photo diode. And the transparent one is IR LED.

[@boybravo689]

@@EEWave tnx for the info sir

[@MrNixified]

Hi, i have accomplished this circuit before. And now, i want to use this to trigger a pump using a TIP32C. But why is it that the operation was reversed. When it doesnt detect anything the pump starts. But when it detected something the pump stops. Can u help me?

[@atulmulsha9016]

Reason is there are two types of sensor in market one with 2led and one with 1led , tip32c is used in 2led it sensor , while this circuit is one led it will work with bc 547transistor..i also made today my hand sanitizer machine

[@surapantouchtech]

Ir most can mot work on solar light , how to solve this problem ?

[@kadusirajulmuneer4202]

Does Vout give a single pulse output when an object passes before the sensor

[@pawanmitrarenewableenergy558]

Hai sir we procured the preassembled or sensor module and it's functing but when we bring any objections then the output stops and we remove the objects then the signal comes.what can we do it's inverted can we make any changes in the board itself

[@waseemaboudahr9215]

Hello, how to add a relay 6 v to the circuit to connect a buzzer and how can I use it in the opposite way where when you remove your hand the red led with goes on . Thanks.

[@naderhumood]

Aptly well done.. ✌️

[@Muhammad_Uvais]

Sir v out is analog or digital??

[@EEWave]

Output of this sensor is in digital signal, it is either 0 volt or 5 volt.

[@Muhammad_Uvais]

@@EEWave thank you sir

[@EEWave]

You're welcome.

[@prakashharash8380]

Namaskar sir ji.

[@josesanta3723]

El LM 358 no lo pudego encontrar en la tienda Argentina

[@jaysernal8701]

Thank you so much for this .....

[@mansingpatil3749]

How it works in sunlight..

[@rakeshsharma-bb6jy]

Sir ji yeh bana banaya mil sakta hai kya

[@creativecrackers0079]

I have done this but the led is glowing altime it there was no obstacles why

[@EEWave]

Please adjust the potentiometer. This is to adjust the distance of detection.

[@creativecrackers0079]

@@EEWave i have done if i reduce the potentiometer the led glows dim and brightens as maximizing

[@candrasniper3404]

I have same problem. No obstacle, led still lights on. I have turned the pot till full or zero, but there is no change (led still lights on).

[@kuntalmandal3661]

Please make the circuit on Proteus and make a single layer pcb format

[@sahilakhtar4756]

I made the circuit in the breadboard but its not working

[@anildesai9885]

potentio meter how much resistance

[@axcx4582]

how many volts have the out signal?

[@MimiATechnology]

You can get it with your multimeter, either digital or analogy, set your digital multimeter to the DC volt range and then connect your positive from your DMM to the output and the black wire of your DMM to your Negative voltage supply

[@uditswaroopa5809]

Can you make a video on 7 channel IR Sensor!

[@EEWave]

Yes bro, sure. I'll make a video on this.

[@rickyarchanakumari3444]

Components to discuss karo dada

[@magarajanamagarajanarunach6661]

Wt is the role of 10 k pot in the circuit...

[@EEWave]

To adjust the distance of sensing.

[@magarajanamagarajanarunach6661]

Thank you so much

[@EEWave]

You're welcome bro...

[@magarajanamagarajanarunach6661]

Bro I build it on breadboard but the LED at the pin no.1 it is not blinking

[@magarajanamagarajanarunach6661]

Bro It's working inversely...

[@sonushukla2873]

Sir 24 vdc main banaye

[@EEWave]

24 volt me to IC jal jayega. Aapko 24 se 5 volt tak convert karna padega.

[@jeevakkuwar]

what is the range of proximity it can detect? Also, how can we increase the range to about 2 to 3 meters (I'm trying to do this for a gate opener) ?

[@EEWave]

Its maximum range is apprx 0.5 meter. If you want to increase the range then connect more IR LEDs with this.

[@mihinidarshi8938]

Tanks

[@drr4196]

super

[@nathnarayangupta8291]

It is to good ,thanks😊

[@EEWave]

You're welcome friend.

[@edgardoescudero4505]

Muy buen video!

[@udaykarthikeya]

How do you make your intro ?

[@chikka.dheerajnetha8075]

How much money it's spend to make this

[@EEWave]

Approximately 35/- Indian Rupees.

[@sundaramurthig2813]

Please provide the diagram in clear

[@sanjaybaghel1968]

Can it work on 3v supply

[@Golkun1]

yes, you just need to adapt the resistor values.

[@AbhishekDwivedi-qk7cz]

circuit diagram

[@samlorca7974]

Hablas español verdad

[@chikka.dheerajnetha8075]

With pcb it cost 35 ha

[@ProphetTLK]

100% not working

[@Golkun1]

100% your fault

[@deepanjalimishraa]

I tried this and this doesnt work it is ‼️‼️‼️‼️‼️‼️‼️‼️‼️‼️‼️fake fake fake‼️‼️‼️‼️‼️‼️‼️

[@IIT2007]

Bro make a video plz how to make hand sanitizer machine using this sensor or else plz tell me can I use this???

[@IIT2007]

Bro make a video plz how to make hand sanitizer machine using this sensor or else plz tell me can I use this???

[@IIT2007]

Bro make a video plz how to make hand sanitizer machine using this sensor or else plz tell me can I use this???