Ej207 v7 rotated gtx3076r

22 pounds 426 wheel

[@toneyclayton485]

Daaaaaaaaamn… got an RS and will do my swap this Fall… you just put a little fire under me!! They pull!!!!!

[@BcapGarage]

Car sounds nice!

[@siriansight]

bro i love this cheers for sharing man i debating whether to spend 20K on my 05 STI and finally modify it (20G, flex etc) or sell it, ad the 20 and get an a45 vids like this make me know ive got unfinished business - it's now (before kids x.x) or nevr ;)

[@kylestandon4831]

It's fun man, the car has more power and a bigger turbo now. Just check some other videos on the channel

[@brandonjessup3004]

Love the grind boss. I have a V9 EJ207 w/a VF42 that I want to get built for 600whp. What's are the specs on your 207? Which brands should I trust for cams, pistons, rods, etc?

[@Jan-xj5hz]

1w😊😮😅ssa

[@chasestoddard6984]

❤❤❤❤❤❤❤❤

[@Hunter-th1hm]

YOOOOOO FUCK YEA

[@younq_soles5069]

wait I have the same exact set up mostly Built head Im only doing 379hp What else is done? or what u recomend? i needs this😅 33k miles too

[@nashedpotatoes7687]

What kind of power were you putting down with the 3076R? I’ve gut a very similar build, 2.1, pistons rods, o-ringed block, fully built heads, with a BoostLab 62X I’ll be running around 22-24 pounds on pump gas (91) and hopefully 30 ish on E. got a meth kit as well, hoping to crack 500 wheel on pump gas with meth

[@AntiSUS]

May not crack 500 on 91 but I could be wrong. That turbo on 20+ is making 426whp it says in the description.

[@CalumTrevors]

You have ignition cut?

[@escinsanity603]

Hey when does it spool, and does it still run? Also, stock bottom end?

[@kylestandon4831]

Spooled the 3076 at 3900rpm still runs just on a 6466 and built top and bottom end with like 30k miles on it

[@derekwalcott7349]

Garrett?

[@alextroll550]

Hp at hi boost?

[@mariospanagiwtopoulos9442]

I wanna make my passat 1.8t and add this little beast to make it 350++ ... Is this turbine enough for that?

[@HKUxBIGPERMx909x]

On Pump?

[@kylestandon4831]

E85 22 pounds conservative tune.

[@minipancakess]

How much did it cost you to build the 207?

[@kylestandon4831]

We built the heads and used an outfront motorsports v3 block with the closed deck procedure. Used a 2.5 crank to stroke it out a little. Used bc stage 3 cams and oversized valves.also half inch head studs. It was around 6-7k if I remember right

[@minipancakess]

@@kylestandon4831 that's not too bad actually, was expecting a lot more lol. How is the lag on the 30r compared to the 6466 you have now? Does the 207 avcs heads help out at all on a turbo that big?

[@kylestandon4831]

@@minipancakess its a 600 rpm difference. I dont spool till 5100 on the 6466 but we built the heads to rev to 9k

[@minipancakess]

@@kylestandon4831 is that full spool or just the start spooling?

[@kylestandon4831]

@@minipancakess kzbin.info/www/bejne/m2TLmWCnbLmYjtE Here's a good reference

[@arneshkadun2130]

how many HP bro and boost psi?

[@kylestandon4831]

On a new setup now, 6466 at 32 pounds 592 wheel

[@goobygoob9312]

Ok I may get hate for this, but through my shitty phone speaker, it almost sounds like an Evo.

[@kylestandon4831]

It does have an equal length header lol

[@quintenhall]

Dog box?

[@kylestandon4831]

Stock sti six-speed with an ACT clutch

[@quintenhall]

@@kylestandon4831 fuck dude nice shifting then 😂

[@kylestandon4831]

@@quintenhall thanks man, the car is faster now. This is the old setup. I've got videos on my channel of the new setup on a pte 6466

[@quintenhall]

@@kylestandon4831 yea I wanna go this far with my build but college is coming up so we will see. Shit is so inspiring to look at tho can’t wait till I’m pushing hp like that

[@cerocents]

Stock block ?

[@kylestandon4831]

Fully built, Closed deck, ported eveything. Just haven't turned it up yet.