floatless level switch connection | high and low water tank control | Electreca

Floatless level switch
Unlike ordinary level switches that use a float for level detection, the 61F Floatless Level Controller uses electrodes to electrically detect the liquid level
The Level Controller would automatically operate the pump, to control the liquid level in the tank.
Floatless are used in two different way
1) they are used to protect the pump from getting burnt in case the water levels are low only in the borehole, well and ground or surface tank
2) to control the pump that is filling the overhead or upper tank.
WATCH MORE VIDEOS HERE
FLOAT SWITCH|flaot switch high and low • Float Switch Wiring - ...
Float Switch Selector Switch connection • Float Switch Selector ...
How to use the float switch in the tank • How to use float switc...
CHECKOUT THIS PLAYLIST...... LEARN MORE ABOUT CONTACTOR
• contactor serie
SUBSCRIBE TO THE CHUNNEL www.youtube.co...

[@abassembatya]

Thanks for the educational videos David. We really appreciate, I request that for such videos of circuits and connections, I request and suggest that for each pin that you connect, you say it out loud so that we don't get left behind. Some of these components are new to us. Thanks again.

[@electreca1]

Understood! Thanks for watching

[@kaundabwalya7776]

Well explained Sir 👍 God bless you 🙏

[@hajimuhammad2928]

Thank You Very Much, Sir. Kind Regards From, Karachi, Pakistan

[@mayeelect]

Thank you so much for contribution to knowledge. Please I have questions: what type of electrode is used in the connection, is it normal Earth electrode? 2. Would the water in the tank not carry current that can get one electrocuted? Thanks in advance for answering the questions.

[@electreca1]

Earth electrode tends to be long and naked(not insulated). But for float less are called PROBE. They have insulated almost 3 quoters of their length and only a tiny tip is exposed. There is definitely a leakage in the tank, But as I said in the video, Electrode No3 is Earthed. When you Earth there will be no leakage completely Thanks for watching

[@rawlingsnuweaha3838]

Hi For the nc connection,when it reaches e1 the relay becomes on /off like that until you switch it off

[@davechesney7721]

Great videos just what I was looking for. In a water tank do you use a wire with a bare end, as you used in the demonstration, or is there something specific available. A quick search online didn't come up with anything her in Thailand. Many thanks Dave

[@electreca1]

Thank for watching, there are deferent types of probes take look s.click.aliexpress.com/e/_DkQTcXN This can do.

[@davechesney7721]

Thanks for your prompt reply. I will look for those on the local equivalent of Ali Express I did find what Omron call eletrodes ,stainless steel rods. I think that I will use a float switch when we install the water tank. Thanks Dave.

[@itsok2902]

U are my best

[@linossinkala7840]

Super super thankyou sir

[@dennisimujaro512]

What if I short all the electrodes during drain or fill

[@mohamedqadar4478]

I would like to have your contact to learn somethings from you.thanks

[@86benjah]

Quick question assuming the two bulbs are pumps will it drain and fill the tank without you rewiring the circuit?

[@electreca1]

Yes

[@abassembatya]

Replace the bulbs with the contactor coils of the respective pumps.

[@mathewsnyirenda4004]

So all the 3 probes have to go in the borehole?

[@electreca1]

Yes< But set at deferent hights

[@otengamponsah6034]

How can I get some of the level switch to buy

[@electreca1]

They are widly sold localy but you can get them on Aliexpress

[@gamelover2594]

nice video, pleasure to look at your video

[@ErnestAsodio-ir4ks]

Thanks big man, I just request for your number. Thank you