Electrical tips for wiring up your motorcycle and a quick Ninja update

[@melaniestevens8987]

Love it men we need more people like u make life moreover easier.good job

[@russbug100]

I watch your videos because it does'nt matter if your in America or England Bikes are all the same. I apply your tips when I work on my bike. Nice one thanks. Now lets see a vid of your riding

[@wedginator]

Add a fuse to the positive connection. The fuse should be closest to the power source.

[@wedginator]

Thanks. To unbolt the tank, you'll have to remove the 2 bolts up front, then remove the seat. You should then be able to lift it up easily. The hoses should not get in the way.

[@vibhuvashisht8032]

Hi! Thank you for the tips. I have a ninja 250 and I went on my first ride of the season. Within 5 minutes the tachometer started going crazy and eventually the bike stalled and broke down, I wasn't able to start it again. Someone at a garage checked my battery and said it was fine but suggested I check the grounding wire to see if it's loose. I'm wondering if you could help me figure out where the ground wire is and how I can tighten it down. Thank you!

[@wedginator]

Thanks. 1. One black wire connects to chassis ground. The other black wire connects to the relay. The reason why I did this is the front of the bike does not have a suitable chassis ground. 2. I'm not sure about what mine is rated for. The ones you found on ebay is sufficient for a project like this unless you're planning on pulling more than 15 amps.

[@wedginator]

That's an interesting approach. I haven't seen it done that way with a battery before. I'll post a comment on your video.

[@djadisalim7]

i like your mecanique video,keep going man,good and remarquabel job

[@lukedemeda1376]

I got my first kawi ..zx6r 98 gear box blew so decided to get a completely new engine have put the new one it got everything pretty much on but and ready to turn on and see some light 🤞 but can't seem to find...Ur remember 🤔 the other end of the negative wire comes from?? Any info would be great

[@rohlen6215]

Great tips. I just got a 2009 Ninja 500R. It hasn’t been run in a few years, so I’m taking one issue at a time. I have it started but no headlight. The bulb is good, the connector is good, the ground is fine and the hi / low switch seems fine. When I turn the key all the other lights come on but no headlight. Any suggestions would be greatly appreciated.

[@lampingromeo]

Wow! I was actually just thinking of adding a distribution block to my bike as well! I was gonna use Kulka blocks also, however one for + and one for -. The battery screw is just not long enough to accommodate more than 2 ring terminals each.... smh

[@Chuckles1981]

I love you "how to" vid's, But i dont seem to have a brain for thi sort electrical work hehe. Great idea for the aux sock, I run a GPS, but its connected stright to the battery using a ebay bought item, seems to work well. Keep'em coming!

[@lukedemeda1376]

Great video also made me realize how awful mine is not had the bike long and fit the age makes me wonder who els has had a go 😅😂

[@mffdesigner]

Hi. I got a bluefire alarm system to install in my bike. And I was checking the videos and is saying to get a resistor to setup the anti-highjack system. Do you know which resistor should I buy for my bike 2014 ninja 650r? Thanks.

[@walkerrog25]

Awesome vid my friend, I really enjoyed it. thanks man.

[@wedginator]

Rosin core, 60% tin, 40% lead is what I use.

[@clarkeboss1072]

Hey man you should never disconnect your hot side and leave the ground in take both out and woolah no worries

[@wedginator]

I get this at my electronics store. Ebay should sell them too, try searching terminal block instead.

[@Wolphe22]

Great tut on electrical! I recently installed an LED kit on my bike, but with a twist. My leds can be powered by either the bike battery or a battery pack. Only difference now is I just changed my battery pack in the video with a rechargable rc battery pack. Check it out, I would like to hear your thoughts on it. :-)

[@wedginator]

It could be a problem with your banjo bolt and fitting or your seals have deteriorated. I'll put this on my to-do list, don't hold your breath though as it may take me a while to get to it.

[@futboleroR10]

I love your videos bro simply because I have the same bike. I got an unrelated question. How do you unhook your tank? I tired doing it but There are 2 hoses close to the front that I can not take of because I feel like Im gonna tear them. Do you need to empty out the tank first? Or how do you do it? Is there a video on it? Thanks.

[@Sludgepump]

Nice vid! Very helpful advice.... thx!!

[@danver1818]

Wedginator, was wondering, where do you get that distribution block? Been searching for it but can't find one... you know if they supply that on ebay for instance ?

[@motorcyclerefurbishment8162]

Just wondered which brand your wire strippers were.......ta

[@jwbonnett]

You shouldn't solder cables in any vehicle, this was a lesson learnt from the aerospace industry, due to vibrations the solder cracks and creates a break quicker.

[@soljahblast]

Im using the distribution block diagram from canyonchasres, is your set up the same? If not could you tell me what you would change? My wire running from (relay) pin 30 to the + side of the block is causing my fused wire from pin 87 to + bat. to blow. Plan is to run HIDs,DEVIL EYES, LEDs and I'm using 2 toggle switches.

[@reaperwayne]

Another good vid thanks

[@renzovc]

thanks brother

[@pittbulldutch]

How do you like the hyperpro dampner?

[@sagunadhikari1591]

Hi guys i was having trouble with my ninja 250r 2009 model i was riding home one day after heavy rain which has ended when i was riding but the bike got soaked and suddenly my motorcycle just switched off engine cut off and electrical all died. i moved the motorcycle and checked fuses and my 10A ignition fuse has blown so i replaced it and it started and ran for awhile but then it died again then got it towed home!! My brother took apart the bike the next day and couldn't find any exposed or wires that rubbed anywhere and cleaned the whole ignition wiring. Started the bike up ran perfectly then 10 minutes later the fuse blew again any suggestions or anyone know how to solve this problem??? Thanks!!!

[@wedginator]

Thanks!!

[@renzovc]

Hey man i really need your help i just bought some led lights from led glow and i wanted it your advice on how to connect an in line fuse to it ? Plz help me let me know i could also make a video to show you better how im planning on installing them . Thanks

[@SonicMotoVlogs]

renzovc battery positive to fuse to LED red wire

[@wedginator]

thx bud. Will do.

[@apracing01]

Once again A+++++++++++++

[@foxbraap6373]

google search "motorcycle power relay and distribution block" first link from canyonchasers your welcome

[@32marcopolo]

Apple 15.02

[@apracing01]

Once again A+++++++++++++