Hi, your info was very helpful. Need your support on how to auto start the motor as soon as the power is turned onn for the VFD, means which wire that needs to looped?
@francoismicheaux89944 жыл бұрын
Hello , thx for sharing this info, I am kinda new to the VFD world, I have a question, which terminals would I use to have a separately derived 24VDC running through a dry set of contacts/relay that will close when the motor is in motion ?, thx in advance for your assistance, cheers!!!
@rodegirmesiano22577 жыл бұрын
Your video is great, now Please show us how to configure LS IGGA to increment RPM using push button as input.
@विनायकविनायक-ल5श4 жыл бұрын
what is reset parameter of drive?
@zeeshanahmad70702 жыл бұрын
Explain please 1) Factory reset kaise kre ? 2) push button se chlane ke liye koon koon se parameters use krne he ?
@fomenkyjonas36385 жыл бұрын
How can we connect capacitor bank with vfd to correct the power factor?
@Hemantsaini04783 жыл бұрын
Overload ke liye btaoo kuch
@yasirpunjabi995 жыл бұрын
Hi. Please need some help any one knows about LS is7 and IV5 models inverter capacity setting beacuse i'm install 3.7kw inverter cpu board on 11kw and ampair defrrence show on keypad and external ampaire meter please any one tell me how to set inverter capacity set this parameter not in manual
@subasgurung95445 жыл бұрын
Hello, sir, my motor is not running when connect to Ig5a inverter, what to do...
@tahaqureshi54504 жыл бұрын
what is default function mode of ig5?
@abbas19677 жыл бұрын
Please complete the setup , start from beginning how to set the speed by keypad and so on
@charltech142110 жыл бұрын
can you show me the wiring diagram? i have here ls sv040ig5a-4, but i dont know how to use
@mohammadfahim68235 жыл бұрын
Come
@ishfaqali46895 жыл бұрын
Sir My vfd rpm is set on 100rpm how can I set it to 400 rpm
@MIZUTECH5 жыл бұрын
yes bro help u so plzzz text
@mohamedabdu9324 жыл бұрын
dear sir the inverter gives inverter overload one time and overload trip another
@R.S.ELEVATOR4 жыл бұрын
LVT fault please sir help me
@sobints87954 жыл бұрын
How can we restore the factory settings
@abbas19677 жыл бұрын
Hi, what is the amount of potentiometer used for controlling the motor in kohm ?
@ionsuditu69852 жыл бұрын
any type from 1Kohm to 10 Kohm( 1k, 2.2K,4.7K.10K)
@khaleddiab83379 жыл бұрын
Thank you for sharing experience
@nadeemrashid93198 жыл бұрын
please hlp me....i have err error in my ls ig5 invrter how i can solve it
@bismillahelectronicsindust98245 жыл бұрын
Cpu card error
@Watchtillend2798 жыл бұрын
How get frwd the? Bcoz it run in reverse
@blackhornet34595 жыл бұрын
Bro how can I lock keypad in this vfd?
@MIZUTECH5 жыл бұрын
i uploded my channel vedio plzzz wach
@bismillahelectronicsindust98245 жыл бұрын
Sir you please little video share on inverters repairing thanks
@MIZUTECH5 жыл бұрын
yes bro
@peerzada0076 жыл бұрын
How to replace it with smart motor controller
@Machiuka8 жыл бұрын
It could be run on 1 phase input?
@CuongTran-tv6pn6 жыл бұрын
..........
@bismillahelectronicsindust98245 жыл бұрын
Yes sir I can operate 1 phase input side give 220v and get 220 3phase outside
@hieudo359110 жыл бұрын
Dear EMAINC. now i want to set up ACC and DAC for each speed. could you please show me how to set it. i want to control 3 speed, speed 1 ACC and DAC 20s, speed 1 ACC and DAC 40s, speed 3 ACC and DAC 180s. can we set up IG5A like that. today i wasted many hours but i can not set up it. Thank you for sharing experience
@bismillahelectronicsindust98245 жыл бұрын
Sir you can multi speed set then you each parameters set on multi speed pi p2 p3 soo on then you set Acc and Dec by parameters setting
@farazahmed99378 жыл бұрын
Dear sir i want to run this iG5A invter upto 60hz on variable mode. May you demostrate?
@bismillahelectronicsindust98245 жыл бұрын
Increase the base and maximum frequency using programming setting