The vent is not for condensation. It's for the barometric sensor
@raoofabd30332 жыл бұрын
Thanks for your on explain the ECU
@coursesolutions5692 жыл бұрын
Glad to help
@RichieRich8452 ай бұрын
The sealant is Sikaflex 227 goes on like RTV but when dry stays flexible. The black knob is not for moisture it for atmospheric pressure, barometric (air pressure) pressure sensor is built on the circuit board.
@vitorsantos1319 Жыл бұрын
Thank you for the great explanation, it made our understanding much easier.
@JohanLouw683 ай бұрын
Nothing better than the old school.
@YakobWakjera8 ай бұрын
Ecu with all its glory.... Amazing 😊
@campbellmorrison8540Ай бұрын
The problem I have with modern electronic modules is the inability to get datasheets on many if not most of the chips used. Do you have any resources for automotive chips, the manufactures seem to supply data for the very latest but not the older ones which is what tends to be used in faulty modules.
@phybillgate458610 ай бұрын
THANK YOU FOR YOUR EXPECTATION
@MWXYT2 ай бұрын
So you don't know which component does what. Except for a diode and caps. Thanks for the explanation.
@deerhunter8533 Жыл бұрын
Heat the edges of the case with a heat gun and use ecu cover extractor tool to remove the cover. Makes the job a lot easier without destroying the ecu case
@mi-mn4ccАй бұрын
I want to learn ECU repair. What do you recommend for the devices I should use? Thanks
@ChristianGomez-b6d5 ай бұрын
Can I convert a auto pcm to manual by removing a chip or rissistor?
@indian90332 ай бұрын
Ecm black button working?
@abnad2827 Жыл бұрын
Hello, and thank you for the video, it’s excellent and informative. I have a 2012 Volkswagen, the multimedia radio, the interior light and the sunroof no longer work but everything else works perfectly. The diagnosis tells me there is a control module fault with the code: 1048642. How can I repair this fault? Is it the soft out The hardware that is at fault? Thanks a lot for your help.
@coursesolutions569 Жыл бұрын
Start with the basics like checking fuses and resetting control modules. If those steps don't work, consider software updates and, if necessary, professional assistance for control module replacement. Remember to prioritize safety and consult with a qualified mechanic to ensure a proper and lasting repair. Good luck with getting your Volkswagen back in working order..
@abnad2827 Жыл бұрын
Hello, and thank you for the answer, please how to do resetting bcm? Where can I find software upgrade? The like is done. Thank you for the videos.
@viridian69039 ай бұрын
Try to hard reset or sw reset
@Sasuke_05 Жыл бұрын
what if the ecu does not want to go out of the ground to the relay of the starter? What is thr cost? 
@coursesolutions569 Жыл бұрын
If the Electronic Control Unit (ECU) is not coming out of the ground to reach the starter relay, it suggests a possible issue with the ECU's connection or wiring. The cost of resolving this problem can vary depending on the specific circumstances and the extent of the repair required. It is best to consult a qualified mechanic or automotive technician to assess the situation and provide an accurate cost estimate for diagnosing and fixing the issue.
@sameerag5236 Жыл бұрын
1999 honda civic rpm up and down i replace iac val what tha problem
@coursesolutions569 Жыл бұрын
If your 1999 Honda Civic is experiencing RPM fluctuations despite replacing the IAC valve, there are several other potential culprits to investigate. Check for vacuum leaks, clean the throttle body, and ensure proper idle speed adjustment. Also, inspect the TPS and MAF sensors, the fuel system, electrical connections, throttle cable (if applicable), and exhaust system for issues. Verify engine timing as well. If the problem persists, seek professional diagnosis and repair to restore a stable idle and RPM.
@dwamenahakentensampson Жыл бұрын
What can make the ECM spoiled
@user-vk9rq1zu438 ай бұрын
Static discharge and short circuit.
@rgaa12936 ай бұрын
Diagram ecu ?????
@SokeElektronikKartTamiri Жыл бұрын
@simcamargo33123 ай бұрын
saan po nag reper ng ganyan
@sametalici877 Жыл бұрын
Hello can you repair continental getrag dc4 tcm
@MariaSoto-n2e11 ай бұрын
I have son problem ,the scanner conect ob2, turn on the scanner ,the ecu not comunication to the scanner.what the problem
@phonetracker57496 ай бұрын
check for signs of water around ecu and wiring connectors
@devl85656 ай бұрын
Depending on year might be a gateway module too , should be close to the obd port, you got a GoDiag breakout box or similar?
@joecantu52523 ай бұрын
Check cigarette lighter FUSE, replace BLOWN FUSE, then plug scanner and NOW IT WORKS, COMMUNICATION
@nurbaini43082 жыл бұрын
Next video... How to flash ecu
@coursesolutions5692 жыл бұрын
Noted...Thanks for sharing your concern. I will definately make one video related to this 😋
@joseabellasr975 Жыл бұрын
Sir paano hende mag restart sir
@w3svc2 ай бұрын
the sealant is butyl-tape
@dolphin265Ай бұрын
Uh that first chip caught my attention too it looks an awful lot like a ceramic GPS/GLONASS antenna
@TheJavaSync Жыл бұрын
Voltlog #225 ❤
@لاإلهإلااللهمحمدرسولالله-ث2ق8ث Жыл бұрын
The speaker is egytian
@sakabatanuki97446 ай бұрын
I cannot understand your explanation.
@JohanLouw683 ай бұрын
Had endless problems with these electronic crap they use on modern cars.And if there is a problem then the greediness of us humans come out.For the price of an ecu or even some sensors you can buy a new car.
@لاإلهإلااللهمحمدرسولالله-ث2ق8ث Жыл бұрын
مصري
@JohanLouw683 ай бұрын
Let's call it electric crap.
@f14v14n4 ай бұрын
What a ripoff, you've just taken Voltlog's video and narrated over it, but pretty much said exactly the same things, didn't even add anything new. I wonder if your channel is full of this kind of practices...