1. The copper stuff it antisieze, it lubes the threads to get it tighter, and puts copper particles between the two metals to prevent them from “rust-welding” together in the event you have to remove it again. 2. You gotta have the o2 socket if you can’t get it with an open-end wrench. The new one needs to be snugged down as well, because if it leaks, the upstream sensor will read a lean condition and cause the car to adjust rich. The upstream sensor is the only one that matters in non-emissions controlled states. 3. The downstream sensor, which will be in, or after the cat, only tells you if the cat is working and does not affect vehicle performance at all.
@thomash.5 жыл бұрын
Man, thanks so much! The cheapest shop wanted to charge me like 200 bucks.
@ChrisEdwardsRestoration5 жыл бұрын
ouch!
@sauliuslt35534 жыл бұрын
Thank you from Lithuania , I have Dodge grand caravan 3.8 😉
@jesusisjewish96747 жыл бұрын
Did it just the way you said and it worked great, thanks for the video. By the way, the brown stuff is anti-seize.
@dr174211 ай бұрын
Thank you so much. I will be doing this very soon.
@Rachel40-x7d5 жыл бұрын
Thank u on this my friends van has this same problem and wanted to know more about it Awsome I'm now going to subscribe to :)
@joes31097 жыл бұрын
Thank you for sharing your experience. Can you please give on update on how the sensor performing, is the engine light still no longer lighting up? Can you also give more detail on the O2 sensor..i e did you have to use original equiptment manufacturer. It was mention in other youtuber that using other than OEM might not fix the problem.
@ChrisEdwardsRestoration7 жыл бұрын
everything been great , no more issues or lights or smells. there is a difference in the sensors read the numbers on the original,, Mopar makes several different ones, the aftermarkets can match these if you get the numbers, they are also available on the emissions stickers in the firewall or sometimes door jam. but thanks for the question, all is fine. I purchased the exact replacement on Ebay, it was a lot cheaper.
@josepagan178811 ай бұрын
Remove the air filter cover and your arm fits perfectly to remove the sensor.
@MikeTheGreatOne992 жыл бұрын
…got damm A for effort, Buddy 👍🏾 I watched the whole video
@SomeIsBest4 ай бұрын
2005 Dodge Grand Caravan is rough idling. I replaced all the spark plugs and wires. You reckon the 02 could be the issue?
@ChrisEdwardsRestoration4 ай бұрын
Or the coil packs
@letsthinkitover17 жыл бұрын
Im thinking of inventing a glove with a hard metal square on the thumb so when we reach to take of clips we can push it and releae the clip.
@ChrisEdwardsRestoration7 жыл бұрын
maybe you can get Anthony Sullivan to put it on one of those TV infomercials. I could use it definitely...
@MrFriendsfirst5 жыл бұрын
You unloosened?? you mean tightened?? ha ha just playin, thanx for the video
@ChrisEdwardsRestoration5 жыл бұрын
ahh, you are correct, , sometimes your mouth says things not as you think while trying to narrate your work for a video.
@justabrake7 жыл бұрын
I have an 03 Town&Country 3.8 started bucking while driving then the engine light went on and I smelled a bad odor from the exhaust Got a code P0303 I know it's a bunch of possibilities Do you think it's a sensor ?
@ChrisEdwardsRestoration7 жыл бұрын
P303 is a misfire Cylinder #3 probably a bum wire/plug or a worn out conducted contact in the distributer cap . all real inexpensive
@latonyaswan14416 жыл бұрын
Steven Randolph my car doing the same ,how to fix it.....
@theMekanik2 жыл бұрын
Kewl Thanx!!!!
@elfrescotv Жыл бұрын
Hola, tengo el mismo modelo y no encuentro la válvula EGR, sabes dónde está ubicada, saludos
@ChrisEdwardsRestoration Жыл бұрын
algunos están en la parte posterior de la admisión, algunos en el costado cerca de los cinturones
@ncdoc1006 жыл бұрын
Use a Mopar sensor. The after market ones won’t cause the “check engine” light to clear
@ChrisEdwardsRestoration6 жыл бұрын
i used a denso part which is the mopar replacement
@thurmondanthony93045 жыл бұрын
I changed mine car still runs the same need help
@lloydhlavac6807 Жыл бұрын
@@ChrisEdwardsRestoration Hmmm, in the video you said it was a Bosch sensor.
@ChrisEdwardsRestoration Жыл бұрын
I first used a bosch which was the wrong part then i got the mopar one and ifs been fine since
@Xavie90510 ай бұрын
What type of systems where you getting when you had a faulty 02 sensor ?
@danielguzman83463 жыл бұрын
I got a p0038 . i have a bad cat . Do you recommend to change the heater sensor or do you recommend to replace the cat?
@ChrisEdwardsRestoration3 жыл бұрын
You can try the sensor first as its cheaper
@Xavie90510 ай бұрын
I’m getting P 0135 and P 0134 isn’t that the same thing ? Bank 1 sensor
@ChrisEdwardsRestoration9 ай бұрын
Pretty much either upstream or downstream one
@Xavie9059 ай бұрын
@@ChrisEdwardsRestoration I changed the sensor back 1 , codes & engine lights went away but when I put my key on ignition I see a flashing engine light blinks 10 time and then stays at a solid light it goes away after cars fully started. On the scanner shows no misfires… b I never had it before it popped up after the 02 sensor was changed any help ?
@ChrisEdwardsRestoration9 ай бұрын
@Xavie905 sounds like you need to scan tool, not a code reader
@wheelenhill4 жыл бұрын
Thank you brother. Get you a go pro or a body cam.
@ChrisEdwardsRestoration4 жыл бұрын
That's the plan!
@jamalnasah16255 жыл бұрын
THANK YOU +10
@stbaldawi3 жыл бұрын
Have u see any improvement on gas mileage after your replacement o2 sensor?
@ChrisEdwardsRestoration3 жыл бұрын
Not really. Still 15 if I’m lucky city and maybe 22-25 highway
@CrimsonArchon2 жыл бұрын
My replacement didn't come with a spring, is this normal
@ChrisEdwardsRestoration2 жыл бұрын
Depends on manuf
@charlesh-bey5643 жыл бұрын
I have two codes U110C/U110C pd do it have anything to do with oxygen sensor
@ChrisEdwardsRestoration3 жыл бұрын
The U110C is a BUS Message and usually has to do with both PCM and BCM, because its a lose of BUS Signal between the PCM and the BCM. FIRST THING TO TRY: The first thing I would try is remove the negative battery cable for 20 seconds then replace it. NEXT: Start the engine several times then let idle for 10 to 20 minutes then start it several more times and if the code doesn't return and the check engine light stays out, simple drive it for awhile like you normally would. If the code come right back, below is some common problems. COMMON CAUSES of U110C: (1) Communication with BCM is lost / See if you can communicate with the BCM. (2) PCI Bus Circuit open between PCM and BCM / Check the positive and negative bus signal at both the PCM and BCM. (3) BCM (4) PCM (5) Fuel Level Bus Message is missing Obviously, all these issues must be tested to see which one is causing the problem. BUT first try the battery cable removal and see what happens. Let me know the out come and I'll try to help further. Hope this helps and have an awesome day!
@charlesh-bey5643 жыл бұрын
@@ChrisEdwardsRestoration thank you
@gregoryelmore17797 жыл бұрын
HI CHRIS. HAVE AN 01 CARAVAN. WILL NOT START WHEN CAMSHAFT SENSOR SWITCH IS CONNECTED. WILL START AND RUN WHEN DISCONNECTED. ANY SOLUTION?
@ChrisEdwardsRestoration7 жыл бұрын
run some codes on the ECU and see what it says, have you tried replacing the camshaft sensor?
@markc41665 жыл бұрын
Is this Ned Flanders working on his minivan? Gosh darn sensors
@garyhicks56302 жыл бұрын
I have a code p2097 on my dodge grand caravan and its coming up rich bank 1 so which 02 sensor should i replace
@ChrisEdwardsRestoration2 жыл бұрын
most likely upstream, the same one i did
@kengrunstra10127 жыл бұрын
What was the diagnostic code that indicated this unit?
@ChrisEdwardsRestoration7 жыл бұрын
P0132 and P0135, high voltage o2 sensor and heater wire problem, or something like that
@queenmulatto_63975 жыл бұрын
Was it is very easy to put back in
@ChrisEdwardsRestoration5 жыл бұрын
extremely.
@mcmaldek9 ай бұрын
Everyone usually calls it PB blaster.
@heathermoore26546 жыл бұрын
I have a p0135 code i have the same problem im trying to take it out i have the part and tools for it i have a 2003 dodge caravan
@robertswick44523 жыл бұрын
I need to know how to wire a o2 sensor female plug the wire diagram on a 2007 dodge grand caravan can someone help please do you have a picture of what color go where ?
@ChrisEdwardsRestoration3 жыл бұрын
like this ? www.chryslerminivan.net/attachments/o2-connector-gif.2337/
@hondaxl250k04 жыл бұрын
Just replaced this. Bank 1 sensor 1. Still says o2 heater is bad
@ChrisEdwardsRestoration4 жыл бұрын
Correct sensor.? Bad wire?
@hondaxl250k04 жыл бұрын
@@ChrisEdwardsRestoration not sure. But it’s throwing the o2 heater code. It’s brand new. And the van idles great in park or neutral. Put it in gear it surges and tries to stall. Give it a few rpm and it goes away. I’m stumped
@ChrisEdwardsRestoration4 жыл бұрын
Sounds like the wrong sensor. There are different models of it. A generic one is usually poo. Look at the numbers on the old one see if they match the new. Might be a different sensor. I went through two cheap ones before getting the correct egr coded one
@ChrisEdwardsRestoration4 жыл бұрын
These can also be found on the emission code of the engine or door stickers
@ShazadMohamed093 жыл бұрын
Is that bank 1 sensor 1
@ChrisEdwardsRestoration3 жыл бұрын
I think so
@CrimsonArchon2 жыл бұрын
Yes it definately is
@latonyaswan14416 жыл бұрын
I had a tune up done on my 2005 chrysler town and country and now my car is shaking......😒
@latonyaswan14416 жыл бұрын
i have a code P2097 and it says post catalyst fuel trim system too rich bank 1 , ?????
@ChrisEdwardsRestoration6 жыл бұрын
that means either the O2 sensor went bad, Or they used the WRONG o2 sensor when replacing., the same sensor location as in this video, but on the original there is a emissions code, usually can also be found under the hood or on the door sticker, if you use the incorrect one, your check engine light will come back on almost immediately or after up to temp and toss the codes. be sure they used the correct part
@garyhicks56302 жыл бұрын
@@ChrisEdwardsRestoration hey i got a code for the p2097 code and my code says to rich . which 02 sensor should i replace the upstream or downstream
@ChrisEdwardsRestoration2 жыл бұрын
Its usually the upstream
@garyhicks56302 жыл бұрын
@@ChrisEdwardsRestoration so i have a exhaust leak also it all kind of happended at once and out of no where my van started like sputtering in higher gear like shaking almost but if i let off the gas it stops a little and my check engine light came on and i got the p2097 code
@letsthinkitover17 жыл бұрын
I sure hate those clips
@JuanSandoval-vp9tq4 жыл бұрын
I have the code p0420 on 2005 dodge grand caravan
@ChrisEdwardsRestoration4 жыл бұрын
if you are lucky it is a o2 sensor, if you have my luck it is a upstream catalytic converter.
@JuanSandoval-vp9tq4 жыл бұрын
Now i have the code p0132
@tayloremade2 жыл бұрын
I have the p0420 also. Trying 02 sensor first. I bought downstream. should I have done upstream instead? Haven't put on yet. Juan, what did you end up doing after your p0420 code? Ever get it solved/fixed?