How to clean the inside glass on an Epson Perfection V200 Photo Scanner.
Пікірлер: 91
@orpickaname53446 жыл бұрын
Epson V330 user here -- all the steps are the same. For those asking, in the last step of opening (the long, left hand side) you just need to slide or push the whole top to the left, it will come off the latches easily. All in all it's easier than I thought, thanks to this example. Thanks again!
@doddsnow47146 жыл бұрын
I tried the sliding deal with the V330, just didn't know which end to slide left, the top or bottom, what orientation is the scanner laying, etc. I continued to gently pop off the end where the buttons are and it finally came apart. Thank goodness.
@RussMcClay8 ай бұрын
Thanks a lot! Your nine-year-old video just helped me service my 10-year-old V200. Inside glass is squeaky clean now; it was all fogged up. Your newspaper tip is excellent.
@PaulNeedham-UK9 жыл бұрын
Just started a project to scan old prints and negatives, to find some really bad dirt marks on the underside of the glass. Was ready to throw out and invest in a new V550. But 30 mins later after watching your walkthrough have a clean scan bed and everything working great. Thanks you just saved me £200. On the negative side - got to come up with another justification for a new scanner ;-)
@johnsim3722Ай бұрын
V300 scanner. So easy to open once I seen your video. Thank you!
@ady-uk71505 жыл бұрын
V330 user, it's identical to this one. I had the same problem and just didn't know what to do. Googled it and found your fix. Fantastic, it's like new again, working fine!. Thank you so much for this steady calm step by step video. It's great to see others here have fixed theirs too.
@RosieBillPenguin2 жыл бұрын
Your video is really good and I managed to clean my Epson Perfection V300 under the glass with your instructions. However, it was very difficult to get the scanner re-assembled until I noticed that the scanner bar in your video was actually in middle and not on the end under the power button where it usually rests. I simply used a gentle push to move it forward and the scanner went back in place perfectly and easily.
@txcowboydancer6 жыл бұрын
Thank you so much for doing this video. I really appreciate it. :-) FYI, I have an Epson V30 scanner. The screws and latches were in the exact same place as the scanner in your video.
@Videomanjohn6 жыл бұрын
Thanks!
@toviro7 жыл бұрын
Thank you very much. I started to take my V33 apart but I remembered messing up many electronic assemblies with plastic snap tabs...so my scanner has sat for 9 months. Thanks to your instruction, it is working better than ever - with nothing broken during take apart and re-assembly. Thanks for this.
@kingofallchili2 жыл бұрын
Almost identical to my Epson V350. I was able to clean a band of dust in the glass that collected where the scan bar likes to stay in the center of the glass. Thank you!
@webgraf123 Жыл бұрын
This is an answer to my question. Thank you both.
@rnguyen31043 ай бұрын
Thank you for the info. I used the instruction to the V330 scanner!
@RonGee7 жыл бұрын
Thank you so much for this video. I was having to scan only using half the platen because I had so much grime on the other half. Now I can use the whole platen again. When taking it apart, I had problems separating the top right around where the buttons are located, but I just used a flat blade screwdriver to pry it apart there. For those of you having problems putting it back together, it helps if you fold the cover back on the top half so the thin cover flap by the hinge doesn't get in the way.
@Oleksa-Derevianchenko4 жыл бұрын
This video was really helpful. Epson Perfection V10 has a nearly identical structure. Separating upper and lower parts wasn't as flawless, though. I used two knives. Put them near each scaner's corner, the blade going to the upper side (in other words, not perpendicularly bot at approximately 50-60 degrees). And then carefully moved the blades down simultaneously. It worked, but some minor plastic details were damaged a little. Plus scratched on the side between which the blades were put. I cleaned the inner side of the glass, gathered dust from the bottom and reassembled the scanner. Hope it'll work again)
@poeltrans4 ай бұрын
THX!!! , i also cleaned my good old V330 scanner, just like you told in the video.
@asdf-un9gs5 жыл бұрын
Thank you very much! Thanks to your video I was able to clean the bottom of the glass. It was actually easier than I thought.
@mrhobs3 жыл бұрын
How did everyone do it? I removed the screws, but the end where the buttons are is still firmly clipped into place. Feels like its gonna crack when I try to pull the plastic up. EDIT: Never mind, I wrastled it around some more and showed it who was boss, and it popped open. :P (Large flathead screwdriver helps if anyone's struggling.)
@WiDeIvan2 жыл бұрын
Thank you! Your video helped me and saved my time.
@jameshost63432 жыл бұрын
I always wonder why these manufacturers use breakable clips instead of putting more screw posts. Thanks for the video.
@CarylJeanStudio11 ай бұрын
Thank you for a helpful video.
@andrewwatson11718 жыл бұрын
Worked a treat thanks (mine's a V350, but the setup is identical).
@qoralstn15 жыл бұрын
perfection v37 clean the inside of the glass in the same way. Thanks your video
@starsk13 Жыл бұрын
Thank you so much !! It helped me to fix my Epson Perfection V370 Photo scanner !
@Wascal596 жыл бұрын
Grand merci ! Votre vidéo m' a permis de ne pas tout casser... Il faut juste de la dextérité pour désemboiter l' ensemble, attention !!!
@locduc63742 жыл бұрын
Thanks for your helpful Info
@erictenbensel65908 жыл бұрын
Thanks a lot for this video, I have a V330 which has the lid hinges on the other side, but your instructions helped me a lot to get it open.
@osmansokullu61376 жыл бұрын
Hi Eric, if appropriate for you, I would like to know more about opening top cover of V330. Can't open the button side and do not want to force plastic parts.
@orpickaname53446 жыл бұрын
I assume you already have the long, right hand side open, which you did by pulling upward, then maybe with a little help using a flat screw driver or a credit card, extend the opening to the short sides. Lastly, for the long left-hand side, don't pull it upward because that's where the latches are locking it, but instead push or slide the whole top to the left, it should come off more easily.
@dinacarruozzo48258 ай бұрын
Thank you very much from Italy!
@mayankmadhok3 жыл бұрын
Thanks so much this helped me get such a clear image!!!
@wallflower_es2 жыл бұрын
Really useful, works very well with my V100. Thank you so much.
@Hoooche4 жыл бұрын
Thank you very much. Cleaned up my V330. It has similar construction
@mutiur73962 жыл бұрын
I sort of get vertical bars or lines .... Can cleaning the glass remove these bars... These bars are very dim... Just the color is fade at the interfaces of these bars... Usually the bars are 5mm or less vertical fade colors of scan in appearance
@nexso3 жыл бұрын
It works with my V100. Thanks man!
@paulsheriff7 ай бұрын
i know its 9 years bacl lol but do you think there is a possability that the trasparty widow light on mine could be broken have not used it in years but just got sent some slides gave it a go on windows 11 no luck no scan button pressing alt key prings back the scan buttton but when i go to film it greys out ..then if a preview its just say remove mat or close lid ..so its software or light broken ..not sure .sofware does work better on older laptop on windos 10 ..but again go to film and greys out ..and same wiith previeuw close lid and or remove mat
@annapavlova65544 жыл бұрын
Thank you very much! I have same problem with Epson V100. This video is very useful!
@the75way7 жыл бұрын
Can't thank you enough!
@sanosody3 жыл бұрын
Thanks a lot for this video
@marlonjohnfreyburger62424 жыл бұрын
C’est un super scanner ce v200, increvable. Je vais nettoyer ma glace elle en a besoin après une bonne décennie. Thank.s bravo x 1000
@nadiajones5378 Жыл бұрын
Thanks so much you are a lifesaver ))
@eliseleonard14625 жыл бұрын
Many thanks!! No more stains on my scans :)
@richlovato7 жыл бұрын
Awesome, you saved my scanner!!!
@markreep78417 жыл бұрын
I've trashed scanners trying to get them open, this worked great. Thanks brother
@webgraf123 Жыл бұрын
Thank you for sharing.
@narglin5 жыл бұрын
Thank you, it worked for my v37 as well. However my problem is with lint accumulated where the glass is glued to the frame, I really don't know how to get rid of that. I figure since it's very close to the white calibration stripe, it's the reason why I get vertical streaks on my scans ._.
@mathispyt86034 жыл бұрын
ty man it helped a lot
@asdf-un9gs4 жыл бұрын
Thanks! I was able to clean the inside of my Epson Perfection V30!
@anjorui23133 жыл бұрын
thank you!! you saved my life
@tbonky5 жыл бұрын
very helpful! I have a V100, and the disassembly was the same.
@charli48 ай бұрын
Muchas gracias. Mis escaneos estaban saliendo como con una niebla, y es que era el cristal que estaba muy sucio por dentro.
@snakeoil1155 жыл бұрын
Yep - classic how to video - Thanks - great video
@fascistalien Жыл бұрын
Que grande, muchisimas gracias
@MetaAF5 жыл бұрын
So I have the same model, but had issues when I reached the part at 1:58 when you say “push forward”. The area around the buttons did not want to budge no matter which way I pushed. I did manage to pry mine open but a small plastic piece fell off. Not really a big deal, was able to put back together and works just fine, but can anyone clarify what I was supposed to do at this step for if I need to do this again? Thanks for making this video I’d have been totally stumped otherwise!
@whosthere96666 жыл бұрын
Awesome! Thank you. It works also with the V330.
@Bipen24 жыл бұрын
It is better to spray on the paper than the glass to avoid it from flowing uncontrollably down the glass.
@shayanakadidal78952 жыл бұрын
Getting the hinge edge back on was harder than getting the non-hinge edge off! My hinge eventually busted but the case came together once the hinge was removed and now it works again.
@dmov2242 жыл бұрын
Thank you !
@mawebb886 жыл бұрын
Saved my bacon. Thanks.
@vadimkudakov76495 жыл бұрын
Спасибо, дядя Джон! :-)
@oleksiykumatrenko13727 жыл бұрын
Useful advice. Many thanks!
@peterschielen7 жыл бұрын
Thank you! Worked like a charm
@athenesnormande7368 Жыл бұрын
Thanks for sharing
@БоряБорисов-х1ы6 жыл бұрын
Большое спасибо! Теперь понятно как разобрать сканер и почистить стекло. В сервисе за это много просят.
@ТарасХвостенко3 ай бұрын
Thank you
@marie-francoisemelchior25744 жыл бұрын
Merci beaucoup 😀 Votre vidéo m'a bien aidée.
@sambatya9033 Жыл бұрын
Спасибо, дружище!
@daviddamerau32137 жыл бұрын
i did this like 18 months a go and my scanner scans blurry photos, no matter what setting i use. any idea why? i just grabbed it out from the back of the cupboard to try and fix it........
@Videomanjohn7 жыл бұрын
You may have changed the alignment of the scanner element.
@SamirIrfanUK6 жыл бұрын
Thanks for sharing, this is really useful :)
@LukeLu746567 жыл бұрын
really helpful info. thanks a lot!
@jaapvanhoewijk64887 жыл бұрын
thank you so much!
@ertopix6 жыл бұрын
GREAT! Thanks a lot :)
@galaxystar43253 жыл бұрын
Thanks
@crocellian29727 жыл бұрын
Try a heat gun or hair dryer around the edges. Just warm it to the touch. It comes right off.
@charleskafka9 жыл бұрын
thank you thank you thank you and did i say thank you?
@vasylgarnyk39075 жыл бұрын
Дякую!
@ОсСенний5 жыл бұрын
Спасибо! Помогло.
@MaximBelov-Pro4 жыл бұрын
А у меня не получилось разобрать. С одной стороны защелки не открываются, боюсь сломать.
@RomainBoidevezy6 жыл бұрын
Thank you, works the same on Epson v300
@ВасяПупкин-ы8ь3 жыл бұрын
Вот спасибо! Единственное, что нашел по разборке этого сканера.
@Emesash Жыл бұрын
God. how tight the latches are in it. I had to suffer
@snitzelll37103 жыл бұрын
MANIAC USING NEWSPAPER WTF. THAT'S WOOD FIBER BASED, SCRATCHING SHIT
@Mimizu6666 жыл бұрын
tl;dw - unscrew the two screws by the hinge, open, clean, close, screw.
@bruceblosser3847 жыл бұрын
I really wouldn't trust inked newspaper to clean the inside of a scanner. Too much gunk on the paper... and who knows what chemicals are used in newspaper ink these days!
@Videomanjohn7 жыл бұрын
Use it to clean glass because it is lint free.
@fudgeologyfive4 жыл бұрын
@@Videomanjohn Won't the paper scratch the glass though?