Nissan/Infiniti Motor Mount Replacement! Infiniti G20,Sentra, Maxima,Altima Motor Mount Replacement!

Hey guys I finally made a video showing you how to replace the 3 motor mounts on a Infiniti G20 that comes with a sr20 engine. Now this process with apply to vehicles that are equipped with FWD sr20 engine such as the Nissan Sentras that were produce around this time. You will also find this information helpful if you have a Nissan Altima, Nissan Maxima or an Infinti i30 since Nissan used similar crossmember supports. I didnt do this but Its recommend that you replace your crossmember bushings if you are replacing your motor mounts. Also If you are attempting this repair please make safety your number one priority. If you found the information In this video helpful please make sure to give me a thumbs up! I hope everyone has an awesome day and I will see you all In the next video!
If you wish to contact me for any reason you may do so at my email
[e-mail].
Follow me on Instagram to get sneak peaks of upcoming videos!
www.instagram....
Check Rock Auto for parts used in this video
Front
BECK/ARNLEY 1041453 {#1030728, 1041334, 112702B010} Info
Rear
BECK/ARNLEY 1041333 {#1041177, 1041360, 113202B000}
PIONEER 607312
Front Right

[@freestyleskyline]

Fantastic video man!! I just bought my manual G20 and the motor is flopping around like upstream salmon by a grizzly bear. Definitely ordering mounts and getting this done asap. Very very clear and concise video. Will be checking out more of your channel!

[@BradPaul1863]

Not my car exactly, but EXCELLENT video. Very good so far.

[@ERICSDIYGARAGE]

thank you, Hope it helped!

[@gabrielsoria8935]

can u do a video changing out the transmission mounts? great video!!!

[@ERICSDIYGARAGE]

Gabriel Soria yes I can look into it since mine is going bad 👍

[@gabrielsoria8935]

ERICSDIYGARAGE thanks man!!!! you are the g20 doctor

[@66lwmorgan]

Hey Eric, how long did the job actually take to do? Also,how can I tell what my paint color is? There's nothing on the inside door jam. Thanks for sharing.

[@jialiblob]

Why is the pioneer front right mount on rock auto so expensive now 💀I'm guessing the parts from a p10 and p11 would be different.. Would it be terrible to buy a kit of an automatic transmission and swap the rubbers from the new parts to the old?

[@tonycervantes4816]

Is the same on 97 Nissan maxima gxe bro ??

[@cpd969]

Hi! I hear this a lot that aftermarket engine mount do not last a year. How’s the Beck Arnley engine mount so far?

[@ERICSDIYGARAGE]

how's it going! the mounts are still holding up, I used cheaper mounts that last less than 1 year so it is true but these seem like they are better quality

[@cpd969]

Thanks for a quick reply.

[@carolvaughn4578]

Question) I have a Nissan Sentra XL 1.6 auto trans, when I put it in reverse the whole engine jumps forward which motor mount should I replace I just replace the driver side axel (CV) the knucled part of it axel was out o fhte shaft, and jambed into the motor, (No damange to motor)

[@ERICSDIYGARAGE]

it would be a combination of both mounts since the other might be compensating for the bad causing both to fail

[@ov7960]

👍

[@hunterplays2662]

Hey man I just from ur channel and everything was explained crystal clear now I can replace it by myself u just earn urself a new subscriber

[@ERICSDIYGARAGE]

Hunter plays thank you!

[@tonycervantes4816]

Bro When you put the croosmember you move of jack of the oil pan. Isn't the engine supposed to be supported?

[@viclou7401]

At the 6:15 mark you were putting back the cross member, I didn't see the floor jack on the oil pan and I saw the engine shaking alot when you were reinstalling. Was everything being supported by the other two motor mounts on the sides? I plan on taking mine out, out of my Nissan.

[@ERICSDIYGARAGE]

yes the transmission mount and passenger mount were holding the engine. I had to use the jack to lift the engine from the crossmember to get everything lined up

[@Dmonieluv]

Great video, really need to do this on my 94 Maxima SE/VE. This inspired me to do it myself, thank you.

[@Craftin.Clever]

Thanks for this video 👍 doing this today on my Nissan Pulsar.

[@Zeppelinlv2007]

10:49 , for those having getting the bolt in due to misalignment, use a long screw driver and go down through that left side hole and use leverage by pushing sideways so the holes align and you can now screw in the the bolt to the engine block.

[@roderickhanlon8939]

It is people like you that makes me believe in humanity again. Appreciate you fellow friend.

[@tonycervantes4816]

What year is that car and what model ??

[@budleyfranks9393]

My driver side shaft is falling out of the cup and the passenger side shaft is on an angle, my engine is slanted. What is the problem here? Could it be the subframe?

[@ssmith3494]

So the a Nissan Sentra & an Infiniti like the same under the car ? Same process excuse my incompetence new to the car stuff just learned how to change my oil today 😂

[@-iIIiiiiiIiiiiIIIiiIi-]

10:26 AKA "I gotta go to work and I don't got time for that shit right now."

[@robertmckee6314]

When you put the motor mounts back in, did you let jack dowb from under oil pan? And jack up the cross member in the rear? And then jacked up the front?

[@ERICSDIYGARAGE]

I only jacked up on the rear of the crossmember and then the front

[@ERICSDIYGARAGE]

Hey guys if you found this video help please make sure to give me a thumbs up! check out the original video kzbin.info/www/bejne/iKPNpmmVd6-XhNk

[@SkaterChris26]

What is the name of the part that bolts into the front of the crossmember?!

[@mrromero3871]

You recommend any websites to order new motor mounts?

[@jasonwaltman3566]

Thanks for listing the part #'s. Super helpful man :)

[@ERICSDIYGARAGE]

Glad they helped thank you for watching 👍

[@jpvalenz4699]

No entiendo ala verga el puto ingles

[@ERICSDIYGARAGE]

perdon 😕

[@mpmattson]

Got it done today. I recommend getting the back 17mm crossmember bolts in first - much easier. I really struggled to get the holes lined up but, unbelievably, they finally did. Thanks again Eric.

[@ERICSDIYGARAGE]

thank you, Glad the video helped 👍🏻

[@stetsonaidan3404]

i guess im asking the wrong place but does anyone know a way to get back into an instagram account..? I somehow lost the account password. I appreciate any tricks you can offer me!

[@lincolnjudson8172]

@Stetson Aidan Instablaster :)

[@stetsonaidan3404]

@Lincoln Judson I really appreciate your reply. I got to the site on google and I'm trying it out atm. Seems to take a while so I will get back to you later when my account password hopefully is recovered.

[@stetsonaidan3404]

@Lincoln Judson It did the trick and I actually got access to my account again. I am so happy! Thanks so much you saved my ass!

[@Ninoy2059]

Great Video. thank you for sharing.

[@ERICSDIYGARAGE]

Thank you for watching 👍

[@cgordon2525]

You do a great job in your videos. Thxs

[@srikarwarrior123]

Did you hear ratling noise on bumps when they were bad?

[@ERICSDIYGARAGE]

No

[@Maceboosted]

Thx brooo I have a g20

[@ERICSDIYGARAGE]

thank you for watching hope this video helped you out!

[@Dro_Espi]

Which Motor mounts did you buy? I need to change mine.

[@ERICSDIYGARAGE]

Front BECK/ARNLEY 1041453 {#1030728, 1041334, 112702B010} Info Rear BECK/ARNLEY 1041333 {#1041177, 1041360, 113202B000} PIONEER 607312 Front Right

[@joedurano7126]

How many motor mounts on the Infiniti g20?

[@ERICSDIYGARAGE]

Three motor mounts and one transmission mount

[@joedurano7126]

@@ERICSDIYGARAGE Thanks again, your vids are really helpful

[@ERICSDIYGARAGE]

@@joedurano7126 no problem, thank you for supporting my channel!

[@TanManFixes]

TIPS: when reinstalling the bracket, to put the bolts thru the rubber mounts, keep the jack OFF the engine/oil pan. The motor needs to be bottomed out, in order to line up the mounts enough to where the bolt will slide thru. to line up the rear of the bracket with the studs, I had to jack it up using the transmission case. this was on a 00 nissan altima.

[@stevethomas7167]

Eric, this is a great video. You show early in the video that you are jacking the motor using a wood block under the oil pan. Later, when you are reinstalling the lower brace, you jack the brace to line up the mounting holes for the bolts. Did you use a second jack or had you determined by that point that the engine did not require constant support from underneath so you could move the jack?

[@SuspiciousBelievers]

Eric??? I'm looking for the same info... I saw you removed the jack but didn't show or mention it. 🤔 Makes me nervous I won't lie... recommendation?

[@ERICSDIYGARAGE]

The only reason that you are supporting the engine is so that you can remove the two bolts from the motor mounts that you're replacing if you don't do this there is going to be a lot of pressure on those bolts and you won't be able to slide them out easily you have to remember that you still have a engine mount on the left side and a transmission mount right so the engine won't fall. Once you remove the two motor mounts to Line everything back up you have to jack up the brace that holds the two motor mounts because the holes won't line up.if you have two jacks leave one on the oil pan and use the second one to help lift the center brace

[@ye_traveling_minstrel]

I've watched several videos for the motor mounts already, and this one is clearly the best one I have seen, thank you!

[@yvannovy]

dude, did you really put your jack stands on the oil pan?

[@ERICSDIYGARAGE]

no, I used a jack and wood to support it

[@MumbleVlogs]

Wow bro that’s crazy, I know when I changed mine they were a little better but not by much

[@ERICSDIYGARAGE]

Mumble yeah man these are the worst that I've seen, i changed my front mount a while back and its bad again they dont last long.

[@MumbleVlogs]

ERICSDIYGARAGE they don’t bro, mine started to jerk the motor once I’m going from drive to reverse. Sucks that I just replaced all of them like 3 months ago

[@mohdkhairimohdmushahar255]

@ericsdiygarage do you where I can get FSM for this car?

[@ERICSDIYGARAGE]

here you go web.archive.org/web/20171029164007/nicoclub.com/archives/infiniti-g20-factory-service-manuals.html Get them before they are gone

[@mohdkhairimohdmushahar255]

Thanks!

[@slvrserfr]

I have had an annoying clunking on what seems to be the rear subframe mount. Very helpful in helping to determine the problem I have with my 03 Sentra.

[@ERICSDIYGARAGE]

Glad it helped!

[@DavidHernandez-ue4fz]

I have the same sentra how long did you take to replace it?

[@mikemacdonald2094]

Thanks for the video. Those mounts are a bit of work but straight forward. It's the transmission mount that is most difficult. One of the 4 bolts I just can't remove.

[@ERICSDIYGARAGE]

Mike MacDonald i need to change the transmission mount on mine so maybe ill make one soon

[@Zeppelinlv2007]

When I did mine (twice now), you have to drop it low. 1.)You do this by removing the chassis bolts from the crossmember, then the cross member will disconnect and hang. 2.) Then, use your socket wrench and extensions. A crowfoot flare wrench will help.

[@ERICSDIYGARAGE]

ZeZeppelin2017 thanks for the hints!

[@King__Lord]

Does this apply to a 2001 Nissan Sentra?

[@ERICSDIYGARAGE]

if it has a sr20 yes but regardless it's the same for the 1.8

[@arvindominguez5743]

Great job man thank you 💯

[@elaineruiz938]

Would like it if you could replace mine on my 2002 G20.

[@ERICSDIYGARAGE]

are you in Phoenix

[@elaineruiz938]

No I'm far from Phoenix.. I live in Fresno California

[@yungblade7]

How high up do you have to jack it up for the engine mount? I have a block of wood and my 3 ton jack ready.

[@ERICSDIYGARAGE]

Like 3 inches

[@cheezblock4lllll]

Anyone who is woundering "Leve it for another day" means f it an yeet it lol

[@Khanage911]

Well done sir

[@ERICSDIYGARAGE]

thank you!

[@fermingarciaseoane8328]

How can i check if mines are bad?

[@ERICSDIYGARAGE]

Put the vehicle in Reverse with the brakes on and rev the engine if the engine moves a lot your motor mounts are probably bad you can also do the same thing if you put the vehicle and drive and put the brakes on and accelerate

[@bcotterman499]

Great video, filming and explanations!!

[@ERICSDIYGARAGE]

thank you!

[@JoseChavez-xz4ny]

Nice video , I will be doing my 00 altima soon

[@ERICSDIYGARAGE]

Thank you for watching!

[@nickledimez4012]

Well done!

[@roderickhanlon8939]

Great informational video!!

[@ERICSDIYGARAGE]

thank you I'm glad your found it useful!

[@Iseevideo101]

What about torque (Kn) values?

[@yaquelincuevas3387]

How many motor mounts does a Nissan Sentra have? And where?

[@ERICSDIYGARAGE]

what year Nissan Sentra do you have? if it's a older vehicle like mines it will be in the same location as mines and will have 4

[@yaquelincuevas3387]

@@ERICSDIYGARAGE yes it's an older one it's a 2004

[@ERICSDIYGARAGE]

@@yaquelincuevas3387 it will be in the same location as shown in my video almost identical

[@yaquelincuevas3387]

@@ERICSDIYGARAGE okay thank you so much! I appreciate your help

[@ERICSDIYGARAGE]

@@yaquelincuevas3387 hope this video can help you also replace your motor mounts thank you for watching!

[@rw9036]

Does anyone notice that some of the aftermarket suppliers for these mounts have the bushing orientation screwed up? Sometimes they're off by about 45 degrees, other times they're almost upside down. I've had to press them out and reorient it. It's like they pay no attention, but the orientation is critical for longer life and better dampening characteristics.

[@ERICSDIYGARAGE]

I had issues with the mounting hold I had to make them bigger to fit the bolt through. OEM might be the way to go with these.

[@rw9036]

@@ERICSDIYGARAGE Availability of OE mounts for this application is getting spotty. I just get the Beck Arnley's. You never know what you'll get, but generally I've been happy with their products. Anchor is no go.

[@ERICSDIYGARAGE]

yeah I realized that the hard way, I have a transmission mount from anchor but I'm debating on using it, it has a different design compared to beck arnley

[@Thelegendking-yj4bm]

Driver side mount ?

[@dylangardener1580]

can someone please send me a link so I can purchase all mounts for this specific vehicle.

[@pancholopez1088]

Dylan Gardener just go to autozone and tell them your car info and they tell you how many you need in total and the prize simple bro...

[@ERICSDIYGARAGE]

links should be in my video description

[@DjSoundproofMH]

What is the bar the two mounts connected to called.

[@ERICSDIYGARAGE]

Crossmember

[@jpvalenz4699]

Ehhhhh

[@gentlemanj5443]

Why did you not show the drivers side mount? You only did 3 of the 4

[@ERICSDIYGARAGE]

I have another video showing the 4th one

[@gentlemanj5443]

@@ERICSDIYGARAGE great but I am not seeing it in your videos. I see this one that shows front rear and passenger and another video that shows front again. No drivers side mount under air box.

[@ERICSDIYGARAGE]

@@gentlemanj5443 here you go kzbin.info/www/bejne/l6arc2Wbhp2Ins0

[@kylermahoney3980]

I just broke one of the bolts in the front to the cross member. Any ideas on what to do?

[@ERICSDIYGARAGE]

if you broke it try to remove it with a flat head and a hammer if it broke clean off it should come off with some taps. go to the salvage yard and get another bolt or try your local Nissan dealership.

[@kylermahoney3980]

It's actually the big bolt that bolts the cross member to the frame. I don't think i will be able to get it out unless i drill it out, and even then i am unsure because of the amount of torque it would take to get it out. Any reason to not weld the whole thing to the fram?. I doubt I will replace the motor mounts on this car again.

[@ERICSDIYGARAGE]

@@kylermahoney3980 I would try to remove the cross member again and fix it the right way. these motor mount do not last long, its been one year and mine is broken again.

[@kylermahoney3980]

Thank you for your help

[@الجهني296]

good job but why your engine down oil sr20de 3 liter with oil filter no oil filter 2.8 liter no add more oil and plese show me cleen your engine ^_^