MAZDA b2600i, b2200i truck - NO POWER, BOGGING DOWN? Check This First! // 4K

  Рет қаралды 22,245

PistonShack

PistonShack

Күн бұрын

Пікірлер: 70
@plantmanstudios
@plantmanstudios 2 жыл бұрын
I had a problem with my 1991 Mazda b2200 it bogged down at low speeds. I tried to drive it up a hill and it couldn't do it. After a lot of gas wasted and time spent come to find out one or two of my fuel injectors had died. I replaced my fuel injectors and now it runs like a beast. My new complaint is that is stinks like hell. The exhaust is stinky asf. I too looked for a cat in my exhaust and found none. like wtf. I cannot drive this thing with the exhaust stinking like that so I guess I have to find a cat to install either by itself or have to repipe and refit the whole exhaust system.
@PistonShack
@PistonShack 2 жыл бұрын
Thanks a lot for feedback Shape Shift Inc. I will pin your comment up, make sure other viewers can see it.
@danbasta3677
@danbasta3677 2 жыл бұрын
This is why you need to replace your fuel filter every year to keep contaminated gasoline out of your injectors.
@PistonShack
@PistonShack 4 жыл бұрын
Mazda b2600i Diagnosis and Troubleshooting (ignition, fuel, vacuum and inputs) videos are coming .
@PistonShack
@PistonShack 4 жыл бұрын
Let me know if you have any questions about b2600i Mazda. Cheers!
@adal006
@adal006 4 жыл бұрын
I have the same problem please put the video
@PistonShack
@PistonShack 4 жыл бұрын
@@adal006 Hi Solis, What is your problem with 2600i. I might can help you. What video would you like me to publish first? Cheers.
@adal006
@adal006 4 жыл бұрын
PistonShack when it accelerated it did not exceed 3 thousand just like the video you put when I did not want to accelerate well
@PistonShack
@PistonShack 4 жыл бұрын
Most likely ECU module failed. I would recommend you to get used engine computer from the local junk yard (I found few for less than 50$). That fixed no power/bog down issue. I am working on rebuilding my old ECU - video is coming. Also, what is inline fuel pressure readings at idle and up 2000 rpm? Thanks)
@johnconnolly2377
@johnconnolly2377 2 жыл бұрын
I noticed a lot of hesitation what you trying to speak direct English with complicated words under the internet is Harsh but I'm proud of you for learning so greatly
@PistonShack
@PistonShack 2 жыл бұрын
Live and Learn! Thanks John:)
@user-xq2wr1mn3l
@user-xq2wr1mn3l 4 жыл бұрын
I have a 89 b2600i. Boggs down on full throttle. Idles fine. I've checked ECU, looks great, no problems. I've replaced plugs, cap, rotor, pcv, coil, TPS, cleaned MAF, cleaned intake/throttle body, new wires,, checked for vacuum leaks, I'm at a loss. Thinking possibly fuel regulator or clogged screen in tank. Just had new exhaust put on. 2", no convertor, standard muffler. Still same problem. Any ideas?
@PistonShack
@PistonShack 4 жыл бұрын
Hey B. You done a lot of Good Stuff! I will do next check ups: 1. Check prime fuel pressure, idle pressure and fuel pressure at 1,5-2.0K rpm. 2. Replace fuel filter under the hood, if you haven't done it yet. 3. Check TPS voltage at released accelerator pedal and fully depressed pedal as well. 4. Check ECM capacitors resistance and continuity. 4. Even Ecm circuit board could look okay it doesn't mean pads, traces and other components are in tact. Just get another ECU from junk yard 2200 or 2600i Mazda for 25$ and try it out. I seen it helped few times. BZW, is your Mazda carburettor old school set up or fuel injector? Let me know if you need any data oe specs for any test. Cheers Brotha!
@user-xq2wr1mn3l
@user-xq2wr1mn3l 4 жыл бұрын
@@PistonShack Thanks bro. Yeah, changed fuel filter too. I will try the ecu swap when I have a chance. I assume the ecu has to be the same as mine though? 5 spd, 4wd, same year? Thanks for your help bro!! Love your channel!
@PistonShack
@PistonShack 4 жыл бұрын
@@user-xq2wr1mn3l You're welcome! I would say even ECU from the vehicle with automatic transmission should work but I'm not 100% sure. Automatic transmission on old mazda is not computer controlled by ECU. Happy New Year 2021 To You And Your Family!
@user-xq2wr1mn3l
@user-xq2wr1mn3l 4 жыл бұрын
@@PistonShack You too! Thanks again!
@annahannah5809
@annahannah5809 Жыл бұрын
Need help with my truck b2600i Mazda someone stole my ECU out of my truck and I need a replacement one which years would fit and which years could I use to make it work a 90
@PistonShack
@PistonShack Жыл бұрын
Hi Hannah. That's sad to hear! Based on my experience any ECU from b2200 or b2600i will work on b2600i Mazda. You can find used or even re-manufactured ECU on ebay or local scrap yard.
@sbmasson
@sbmasson 4 жыл бұрын
I used to have one of those 2600 Mazda's ....very reliable...loved that truck
@PistonShack
@PistonShack 4 жыл бұрын
What happened to your 2600i Mazda? Do you still have it or might have some part left over?
@sbmasson
@sbmasson 4 жыл бұрын
@@PistonShack no.sorry I sold it a long time ago. I tried to put a comment on that video twice but it did not record for some reason
@bernardross4136
@bernardross4136 3 жыл бұрын
where do you find the parking light relay
@PistonShack
@PistonShack 3 жыл бұрын
Hey Bernard! Sorry, What is parking light? Did you mean braking lights relay?
@beeg693
@beeg693 Жыл бұрын
You said you didn't have a Catalytic converter, but you didn't check near behind the differential in the back. My catalytic converter is just behind the differential in the very back. I have a Mazda B2600i and mine is a 2 wheel drive from California. I am looking at your channel to see if you can assist me. I see this video is a little over 2 years old. My truck was running fine and then with 30 seconds the engine died. It stalled basically. Mine has two mufflers on the tail pipe one is a muffler and a catalytic converter. Mine looked like it was made that way.
@sbmasson
@sbmasson 4 жыл бұрын
I used to have one of those 2600 Mazda's.....loved that truck
@PistonShack
@PistonShack 4 жыл бұрын
I like those old b2600i Mazda trucks. Basic, reliable small 4x4 pick up truck.
@joshuadavey6489
@joshuadavey6489 4 жыл бұрын
What exhaust does the red one have ?
@PistonShack
@PistonShack 4 жыл бұрын
Exhaust is stock no any mods. I hope it answered your question. Thanks for watching Joshua.
@adal006
@adal006 3 жыл бұрын
Hi how am check the ignition coit ?
@PistonShack
@PistonShack 3 жыл бұрын
Hi Solis. I would start with easiest test first: 1. Disconnect the ignition coil lead from the distributor, hold it with insulated pliers 5-10 mm from a ground, crank the engine and verify that a strong blue spark is visible. If there is no spark, check for voltage at the (+) terminal of the ignition coil with ignition switch in on position. If there is no voltage, check the main fuse, ignition switch, and wiring harness. 2. Primary coil test (read resistance at the small connector between two pins. (0.81-0.99 Ohms) 3. Secondary coil test. Check resistance between main terminal and two pin male connector. One of the pins should read 6-30 KOmhs) Let me know how everything is going!
@scottyhankemeier9380
@scottyhankemeier9380 Жыл бұрын
Mine loss power. Running extremely rich. Coolant temp sensor was bad. Lately my truck is a little low on power though and I can't figure it out. Has rebuilt ECU and new distributor. Guess I need to check injectors..
@PistonShack
@PistonShack Жыл бұрын
Thanks for sharing Scotty!
@scottyhankemeier9380
@scottyhankemeier9380 Жыл бұрын
Coolant temp sensor can fail and cause loss of power idle hanging high. Will cause engine to run way rich. Hard no start, won't Rev up. Walker has sensor w/ connector that is good.
@PistonShack
@PistonShack Жыл бұрын
Yup, I saw the same symptoms on other vehicles. Good point. Thanks for your feedback.
@ecr125x
@ecr125x 2 жыл бұрын
thanks for the videos !! I got that same truck ! any info on why im getting poor MPG / fuel consumption. new cap rotor plugs wires distributor etc. all the basic tune up parts. truck runs very well but only gets 14mpg around town and used to get 20 mpg and above. best ever was 27 mpg on the highway. my b2200 with redline/weber carb gets better MPG .. apps 17mpg in the B2200
@PistonShack
@PistonShack 2 жыл бұрын
Thank a lot for your feedback and sharing the info. You know my 2600i is getting little bit better millage, almost as your b2200. Does truck goes into closed loop after O2 warmed up?
@ecr125x
@ecr125x 2 жыл бұрын
@@PistonShack I’m not sure.how can I tell if it’s in closed loop? I noticed an exhaust manifold gasket leak right after I made this comment and I’m thinking that could be effecting the O2 sensor and fuel delivery. Parts should be here this afternoon and maybe I’ll try to make a video for the Mazda b series community on KZbin (very small and even smaller for b2600i ! ) thanks for the videos!! I’m also considering getting manual locking hubs from an 87-88 but they are hard to find. I’m not a fan of the RFW option and I feel like it creates a lot of drag on the rolling. 👍🏻👍🏻 have a good day!
@TheSpilbillies
@TheSpilbillies Жыл бұрын
My 92 b2600i acts like it wants to start with a shot of starting fluid but won't run
@PistonShack
@PistonShack Жыл бұрын
I would check fuel pressure and engine ignition timing fist before doing any repairs. Any luck so far?
@BobBob-yu1nk
@BobBob-yu1nk 5 ай бұрын
Check compression
@shannanause5205
@shannanause5205 Жыл бұрын
I have a Mazda b2600i and another that is a parts truck I took the computer out opened it up and that's exactly what the problem was I swapped out computers truck runs better than it did before
@PistonShack
@PistonShack Жыл бұрын
Hi Shanna! I am glad this video helped you out. Thanks for your kind feedback.
@manieherbert5515
@manieherbert5515 Жыл бұрын
Engin overheat die and won't start what good be te problem
@jamesrivera4908
@jamesrivera4908 4 жыл бұрын
I’m having this same issue but will happen at random times while driving . I will shut the truck off and then back on and it will run fine until it does it again at random times. I will start to troubleshoot and hope to get To the bottom of it
@PistonShack
@PistonShack 4 жыл бұрын
Hi James! It started acting up occasionally the intermittent problem turned into permanent - No acceleration / bogging down issue. That's matter of time.
@jamesrivera4908
@jamesrivera4908 4 жыл бұрын
I went ahead and took the ecm cover off And right away I discovered a blown resistor on the circuit board . No current flow across it testing with an ohmmeter. Burned around the resistor. Think I have discovered issue. I will replace ecm and see what it does .
@PistonShack
@PistonShack 4 жыл бұрын
Thanks for sharing your experience.That is probably the fix. Let me know how everything is going.
@Mac58058
@Mac58058 4 жыл бұрын
Bro I can’t watch this with you making hand puppets 🤣🤣🤣
@PistonShack
@PistonShack 4 жыл бұрын
Oh, gosh) Interesting! Thanks for check It out.
@rickyelvis3215
@rickyelvis3215 3 жыл бұрын
PistonShack should have given this comment the bird
@donwarrington4916
@donwarrington4916 4 жыл бұрын
this was a common problem on these trucks , especially in hot climates
@PistonShack
@PistonShack 4 жыл бұрын
Seems like that's common ECU issue on them in Canada as well. Thanks Don!
@jayheyliger2736
@jayheyliger2736 Жыл бұрын
Mazda starts but when i press gas nothing
@PistonShack
@PistonShack Жыл бұрын
Hey Jay! How did issue started originally?
@jayheyliger2736
@jayheyliger2736 Жыл бұрын
Thanks for answering. Im going trough it! Truck was running fine but i was noticing a rough idle at time. One of the wires from the distributor was broken. I replaced it with new wires. Was running fine. I added seafoam and since then still fine. Then in traffic im at a light i press down no acceleration. Eventually it caugh itself and started driving again. I changed distributor spark plug(black when i took out) maf spark plug wire. Now when i start it it starts really rough and then cuts of.
@jayheyliger2736
@jayheyliger2736 Жыл бұрын
Im about to change the fuel filter. Can it be the computer or fuel injectors?
@jayheyliger2736
@jayheyliger2736 Жыл бұрын
My truck is doing exactly the same thing the truck in the video is doing
@dljunior2852
@dljunior2852 4 жыл бұрын
I parked my 1990 B2600i up for about a month due to installing a Airbag Suspension. Note it ran fine before parking up but now very hard to start and keep running. Changed out plugs and eventually got it running but had to keep at a certain RPM and now backfires from time to time. Place a fuel pressure gage between fuel filter and I think regulator to see if pressure was constant. Pressure seemed steady. I'm not sure was the culprit is now. I have no check engine light and not familiar how to check code. Hopefully you can help. Looking forward to hearing from you.
@PistonShack
@PistonShack 4 жыл бұрын
Hey Don! Well, b2600i doesn't like to sit they build to ride and explore) Sounds like your Mazda is missing injectors timing impulse, ignition is off or engine control inputs acting up. Alright, I will do the next checks, starting with the basics: Some steps are very basics and simple but quite often get neglected. - check if the air cleaner element is clean; - check ignition timing after war up, BTDC - 6 degrees, green connector grounded; - check for cylinders distribution by disconnecting spark plugs one at a time, check if conditions change; - fill the tank with fresh gasoline, at least 1/2; - check the injectors operating sound at idle; - swap MAF sensor, sometimes it could cause a hard start; - check resistance at injectors harness: terminals B/Y - LG/B and B/Y- LG/R should read 6-8, Ohm; - check for air leaks by listening sucking noises (at idle, when the throttle is open); check fuel pressure when the ignition is ON, test connector yellow pin connected - 38-46 psi; - check fuel pump max pressure (64-85 psi) idle fuel pressure (31-38 psi) could be an issue with fuel pick or fuel strainer up inside the tank. Try to blow compressed air into the fuel outlet at the tank with filler cap off; -check the exhaust system for any flow restrictions; - substitute well-known ECU if the condition will change; - make sure you have fresh fuel in a tank, old fuel can cause loss of power; - check the engine for any vacuum leaks; -check TPS for resistance. Let me know have everything is going and what test results did you get or if you have any questions. Cheers!
IGNITION TIMING MAZDA b2600i, b2200i //4K
7:45
PistonShack
Рет қаралды 34 М.
B2600i Valve Noise Tick's and Rattles, Balancer Chain Adjustment
4:18
World Science TV
Рет қаралды 18 М.
How to treat Acne💉
00:31
ISSEI / いっせい
Рет қаралды 108 МЛН
1991 Mazda B2600i Pickup -- SOLD
7:30
MotoeXotica Classic Cars
Рет қаралды 31 М.
Five Things I Love About my Mazda B Series Truck!
7:06
shiftwrenchrepeat
Рет қаралды 14 М.
82 Ford F-100 speedometer and heater control fix?
13:21
VanGoGarage
Рет қаралды 19
1989 Mazda B2000 - Low & slow | Refuel.no
4:48
Refuel
Рет қаралды 50 М.
Trucker Takes an Imaginary Exit at 65mph
37:59
Casey LaDelle
Рет қаралды 159 М.
What Went Wrong?! Ford Lightning Engine Tear-Down
17:30
Dave's Auto Center
Рет қаралды 67 М.